900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




NXP Semiconductors Electronic Components Datasheet

P89LPC9408 Datasheet

8-bit microcontroller

No Preview Available !

www.DataSheet4U.com
P89LPC9408
8-bit microcontroller with two-clock 80C51 core 8 kB 3 V
byte-erasable flash, 32 segment × 4 LCD driver, 10-bit ADC
Rev. 01 — 16 December 2005
Product data sheet
1. General description
The P89LPC9408 is a multi-chip module consisting of a P89LPC938 single-chip
microcontroller combined with a PCF8576D universal LCD controller in a low-cost 64-pin
package. The LCD controller provides 32 segments and supports from 1 to 4 backplanes.
Display overhead is minimized by an on-chip display RAM with auto-increment
addressing.
2. Features
2.1 Principal features
s 8 kB byte-erasable flash code memory organized into 1 kB sectors and 64-byte pages.
Single-byte erasing allows any byte(s) to be used as non-volatile data storage.
s 256-byte RAM data memory.
s 512-byte customer Data EEPROM on chip allows serialization of devices, storage of
set-up parameters, etc.
s 32 segment × 4 backplane LCD controller supports from 1 to 4 backplanes.
s 8-input multiplexed 10-bit ADC. Two analog comparators with selectable inputs and
reference source.
s Two 16-bit counter/timers (each may be configured to toggle a port output upon timer
overflow or to become a PWM output) and a 23-bit system timer that can also be used
as a Real-Time Clock (RTC).
s Enhanced UART with fractional baud rate generator, break detect, framing error
detection, and automatic address detection; 400 kHz byte-wide I2C-bus
communication port and SPI communication port.
s CCU provides PWM, input capture, and output compare functions.
s High-accuracy internal RC oscillator option allows operation without external oscillator
components. The RC oscillator option is selectable and fine tunable.
s 64-pin LQFP package with 20 microcontroller I/O pins minimum and up to 23
microcontroller I/O pins while using on-chip oscillator and reset options.
2.2 Additional features
s 2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or
driven to 5.5 V).
s Serial flash In-Circuit Programming (ICP) allows simple production coding with
commercial EPROM programmers. Flash security bits prevent reading of sensitive
application programs.


NXP Semiconductors Electronic Components Datasheet

P89LPC9408 Datasheet

8-bit microcontroller

No Preview Available !

Philips Semiconductors
P89LPC9408
8-bit two-clock 80C51 core with 32 segment × 4 LCD driver, 10-bit ADC
s A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns
for all instructions except multiply and divide when executing at 18 MHz. This is six
times the performance of the standard 80C51 running at the same clock frequency. A
lower clock frequency for the same performance results in power savings and reduced
EMI.
s Serial flash In-System Programming (ISP) allows coding while the device is mounted
in the end application.
s In-Application Programming (IAP) of the flash code memory. This allows changing the
code in a running application.
s Watchdog timer with separate on-chip oscillator, requiring no external components.
The watchdog prescaler is selectable from eight values.
s Low voltage detect (brownout) allows a graceful system shutdown when power fails.
May optionally be configured as an interrupt.
s Idle and two different power-down reduced power modes. Improved wake-up from
Power-down mode (a LOW interrupt input starts execution). Typical power-down
current is 9 µA typical (total power-down with voltage comparators disabled).
s Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A reset counter and reset glitch suppression circuitry prevent spurious
and incomplete resets. A software reset function is also available.
s Configurable on-chip oscillator with frequency range options selected by user
programmed flash configuration bits. Oscillator options support frequencies from
20 kHz to the maximum operating frequency of 18 MHz.
s Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator
allowing it to perform an oscillator fail detect function.
s Programmable port output configuration options: quasi-bidirectional, open drain,
push-pull, input-only.
s Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of
the pins match or do not match a programmable pattern.
s LED drive capability (20 mA) on all port pins. A maximum limit is specified for the
entire chip.
s Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns
minimum ramp times.
s Only power and ground connections are required to operate the P89LPC9408 when
internal reset option is selected.
s Four interrupt priority levels.
s Eight keypad interrupt inputs, plus two additional external interrupt inputs.
s Schmitt trigger port inputs.
s Second data pointer.
P89LPC9408_1
Product data sheet
Rev. 01 — 16 December 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
2 of 69


Part Number P89LPC9408
Description 8-bit microcontroller
Maker NXP
PDF Download

P89LPC9408 Datasheet PDF






Similar Datasheet

1 P89LPC9401 8-bit microcontroller
NXP
2 P89LPC9402 8-bit Microcontroller
NXP
3 P89LPC9408 8-bit microcontroller
NXP





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy