http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




Motorola Electronic Components Datasheet

MC54HC574A Datasheet

OCTAL 3-STARE NONINVERTING D FLIP-FLOP

No Preview Available !

MC54HC574A pdf
www.DataSheet4U.com
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Octal 3-State
Noninverting D Flip-Flop
High–Performance Silicon–Gate CMOS
The MC54/74HC574A is identical in pinout to the LS574. The device
inputs are compatible with standard CMOS outputs; with pullup resistors,
they are compatible with LSTTL outputs.
Data meeting the setup time is clocked to the outputs with the rising edge
of the Clock. The Output Enable input does not affect the states of the
flip–flops, but when Output Enable is high, all device outputs are forced to
the high–impedance state. Thus, data may be stored even when the outputs
are not enabled.
The HC574A is identical in function to the HCT374A but has the flip–flop
inputs on the opposite side of the package from the outputs to facilitate PC
board layout.
The HC574A is the noninverting version of the HC564.
Output Drive Capability: 15 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS and TTL
Operating Voltage Range: 2.0 to 6.0 V
Low Input Current: 1.0 µA
In Compliance with the Requirements Defined by JEDEC Standard
No. 7A
Chip Complexity: 266 FETs or 66.5 Equivalent Gates
LOGIC DIAGRAM
DATA
INPUTS
D0 2
D1 3
D2 4
D3 5
D4 6
D5 7
D6 8
D7 9
19 Q0
18 Q1
17 Q2
16 Q3
15 Q4
14 Q5
13 Q6
12 Q7
NON–
INVERTING
OUTPUTS
CLOCK 11
OUTPUT ENABLE 1
PIN 20 = VCC
PIN 10 = GND
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎDesign Criteria
Value Units
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎInternal Gate Count*
66.5 ea
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎInternal Gate Propagation Delay
1.5 ns
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎInternal Gate Power Dissipation
5.0 µW
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSpeed Power Product
0.0075
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ*Equivalent to a two–input NAND gate.
pJ
MC54/74HC574A
20
1
J SUFFIX
CERAMIC PACKAGE
CASE 732–03
20
1
20
1
N SUFFIX
PLASTIC PACKAGE
CASE 738–03
DW SUFFIX
SOIC PACKAGE
CASE 751D–04
ORDERING INFORMATION
MC54HCXXXAJ Ceramic
MC74HCXXXAN Plastic
MC74HCXXXADW SOIC
PIN ASSIGNMENT
OUTPUT
ENABLE
D0
D1
D2
D3
D4
D5
D6
D7
GND
1
2
3
4
5
6
7
8
9
10
20 VCC
19 Q0
18 Q1
17 Q2
16 Q3
15 Q4
14 Q5
13 Q6
12 Q7
11 CLOCK
FUNCTION TABLE
Inputs
Output
OE Clock D
Q
L
L
L L,H,
HX
HH
LL
X No Change
XZ
X = Don’t Care
Z = High Impedance
3/97
© Motorola, Inc. 1997
3–1
REV 7


Motorola Electronic Components Datasheet

MC54HC574A Datasheet

OCTAL 3-STARE NONINVERTING D FLIP-FLOP

No Preview Available !

MC54HC574A pdf
MC54/74HC574A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎMAXIMUM RATINGS*
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
Parameter
Value
Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVCC DC Supply Voltage (Referenced to GND)
– 0.5 to + 7.0
V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVin DC Input Voltage (Referenced to GND)
– 0.5 to VCC + 0.5 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVout DC Output Voltage (Referenced to GND)
– 0.5 to VCC + 0.5 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎIin DC Input Current, per Pin
± 20 mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎIout DC Output Current, per Pin
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎICC DC Supply Current, VCC and GND Pins
± 35 mA
± 75 mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎPD Power Dissipation in Still Air,Plastic or Ceramic DIP†
SOIC Package†
750
500
mW
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTstg StorageTemperature
– 65 to + 150
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTL Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP or SOIC Package)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ(Ceramic DIP)
260
300
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ* Maximum Ratings are those values beyond which damage to the device may occur.
_C
_C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high–impedance cir-
cuit. For proper operation, Vin and
v vVout should be constrained to the
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
Functional operation should be restricted to the Recommended Operating Conditions.
†Derating — Plastic DIP: – 10 mW/_ C from 65_ to 125_ C
Ceramic DIP: – 10 mW/_ C from 100_ to 125_ C
SOIC Package: – 7 mW/_ C from 65_ to 125_ C
For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).
RECOMMENDED OPERATING CONDITIONS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
Parameter
Min Max Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVCC DC Supply Voltage (Referenced to GND)
2.0 6.0 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVin, Vout DC Input Voltage, Output Voltage (Referenced to GND) 0 VCC V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTA Operating Temperature, All Package Types
– 55 + 125 _ C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtr, tf Input Rise and Fall Time
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ(Figure 1)
VCC = 2.0 V 0 1000 ns
VCC = 4.5 V 0
500
VCC = 6.0 V 0
400
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎDC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVIH
Parameter
Minimum High–Level Input
Voltage
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVIL MaximumLow–LevelInput
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVoltage
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVOH
Minimum High–Level Output
Voltage
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVOL
Maximum Low–Level Output
Voltage
Test Conditions
vVout = VCC – 0.1 V
|Iout| 20 µA
vVout = 0.1 V
|Iout| 20 µA
vVin = VIH
|Iout| 20 µA
Vin = VIH
vVin = VIL
|Iout| 20 µA
Vin = VIL
v|Iout|
v|Iout|
v|Iout|
2.4 mA
6.0 mA
7.8 mA
v|Iout|
v|Iout|
v|Iout|
2.4 mA
6.0 mA
7.8 mA
VCC
V
2.0
3.0
4.5
6.0
2.0
3.0
4.5
6.0
2.0
4.5
6.0
3.0
4.5
6.0
2.0
4.5
6.0
3.0
4.5
6.0
Guaranteed Limit
– 55 to
25_ C
v 85_C v 125_C
1.5 1.5 1.5
2.1 2.1 2.1
3.15 3.15 3.15
4.2 4.2 4.2
0.5 0.5 0.5
0.9 0.9 0.9
1.35 1.35 1.35
1.8 1.8 1.8
1.9 1.9 1.9
4.4 4.4 4.4
5.9 5.9 5.9
2.48 2.34
3.98 3.84
5.48 5.34
2.2
3.7
5.2
0.1 0.1 0.1
0.1 0.1 0.1
0.1 0.1 0.1
0.26 0.33
0.26 0.33
0.26 0.33
0.4
0.4
0.4
Unit
V
V
V
V
MOTOROLA
3–2 High–Speed CMOS Logic Data
DL129 — Rev 6


Part Number MC54HC574A
Description OCTAL 3-STARE NONINVERTING D FLIP-FLOP
Maker Motorola
Total Page 7 Pages
PDF Download
MC54HC574A pdf
Download PDF File
[partsNo] view html
View PDF for Mobile






Related Datasheet

1 MC54HC574A OCTAL 3-STARE NONINVERTING D FLIP-FLOP Motorola
Motorola
MC54HC574A pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components