http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf





Micrel Semiconductor
Micrel Semiconductor

MIC2525 Datasheet Preview

MIC2525 Datasheet

USB Power Control Switch Not Recommended for New Designs

No Preview Available !

MIC2525 pdf
MIC2525
Micrel
MIC2525
USB Power Control Switch
Not Recommended for New Designs
Refer to MIC2025
General Description
The MIC2525 is an integrated high-side power switch, opti-
mized for self-powered and bus-powered Universal Serial
Bus (USB) applications. Few external components are nec-
essary to satisfy USB requirements.
The MIC2525 satisfies the following USB requirements: each
switch channel supplies up to 500mA as required by USB
downstream devices; the switch’s low on-resistance meets
USB voltage drop requirements; fault current is limited to
typically 750mA, well below the UL 25VA safety require-
ments; and a flag output is available to indicate fault condi-
tions to the local USB controller. Soft start eliminates the
momentary voltage drop on the upstream port that may occur
when the switch is enabled in bus-powered applications.
Additional features include thermal shutdown to prevent
catastrophic switch failure from high-current loads,
undervoltage lockout (UVLO) to ensure that the device re-
mains off unless there is a valid input voltage present, and
3.3V and 5V logic compatible enable inputs.
The MIC2525 is a UL recognized component and is available
in active-high and active-low versions in 8-pin DIP and SOIC
packages.
For new designs, please see the MIC2025/2075.
Features
Compliant to USB specifications
UL Recognized Component
3V to 5.5V input
500mA minimum continuous load current per port
140mmaximum on-resistance
1.25A maximum short circuit current limit
Open-drain fault flag pins
110µA typical on-state supply current
1µA typical off-state supply current
Output can be forced higher than input (off-state)
Thermal shutdown
2.4V typical undervoltage lockout (UVLO)
1ms turn-on (soft-start) and fast turnoff
Active-high or active-low enable versions
8-pin SOIC and DIP packages
Applications
USB hosts and self-powered hubs
USB bus-powered hubs
Hot plug-in power supplies
Battery-charger circuits
Typical Application
4.50V to 5.25V
Upstream VBUS
100mA max.
VBUS
D+
D
GND
MIC5207-3.3
IN OUT
1µF
GND
3.3V 10k
3.3V USB Controller
VIN ON/OFF
1µF OVERCURRENT
GND
100k
VCC
5.0V
MIC2525-2
EN
FLG
GND
NC
OUT
IN
OUT
NC
150µF
Ferrite
Beads
VBUS
D+
D
GND
0.1µF
USB
Port
Data
Data
Single-Port USB Self-Powered Hub
UL Recognized Component
Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com
January 2000
1
MIC2525



Micrel Semiconductor
Micrel Semiconductor

MIC2525 Datasheet Preview

MIC2525 Datasheet

USB Power Control Switch Not Recommended for New Designs

No Preview Available !

MIC2525 pdf
MIC2525
Ordering Information
Part Number
MIC2525-1BM
MIC2525-2BM
MIC2525-1BN
MIC2525-2BN
Enable
Active High
Active Low
Active High
Active Low
Temperature Range
40°C to +85°C
40°C to +85°C
40°C to +85°C
40°C to +85°C
Package
8-Pin SOIC
8-Pin SOIC
8-pin DIP
8-pin DIP
Pin Configuration
EN 1
FLG 2
GND 3
NC 4
MIC2525
8 OUT
7 IN
6 OUT
5 NC
8-Pin SOIC (M)
8-Pin DIP (N)
(EN) 1
(FLG) 2
MIC2525
LOGIC,
CHARGE
PUMP
3 (GND)
6, 8 (OUT)
7 (IN)
Micrel
Pin Description
Pin Number
1
2
3
4, 5
7
6, 8
Pin Name
EN
FLG
GND
NC
IN
OUT
Pin Function
Enable (Input): Logic-compatible enable input. High input > 2.1V typical.
Low input <1.9V typical (-1 active high, -2 active low).
Fault Flag (Output): Active-low, open-drain output. Indicates overcurrent,
UVLO and thermal shutdown.
Ground: Supply return.
Not internally connected. (For pin compatibility with the MIC2505, connect
pin 7 to pin 5 and leave pin 4 unconnected.)
Supply Input: Output MOSFET drain. Also supplies ICs internal circuitry.
Connect to positive supply.
Switch Output: Output MOSFET source. Typically connect to switched side
of load.
MIC2525
2 January 2000


Part Number MIC2525
Description USB Power Control Switch Not Recommended for New Designs
Maker Micrel Semiconductor
Total Page 12 Pages
PDF Download
MIC2525 pdf
Download PDF File
[partsNo] view html
View PDF for Mobile






Related Datasheet

1 MIC2524 Quad USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2524 pdf
2 MIC2524-1BN Quad USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2524-1BN pdf
3 MIC2524-1BWM Quad USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2524-1BWM pdf
4 MIC2524-2BN Quad USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2524-2BN pdf
5 MIC2524-2BWM Quad USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2524-2BWM pdf
6 MIC2525 USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2525 pdf
7 MIC2525-1BM USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2525-1BM pdf
8 MIC2525-1BN USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2525-1BN pdf
9 MIC2525-2BM USB Power Control Switch Not Recommended for New Designs Micrel Semiconductor
Micrel Semiconductor
MIC2525-2BM pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components