900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Murata Manufacturing Electronic Components Datasheet

SF2380E Datasheet

SAW Filter

No Preview Available !

SF2380E
• Low-loss RF SAW Filter
• Miniature 3 x 3 mm SWD Package
• Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operable Temperature Range
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 2 cycles/10 seconds minimum
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 863 to 876 MHz
Amplitude Ripple, 863 to 876 MHz MHz
VSWR, 863 to 876 MHz
Attenuation, Referenced to 0 dB
10 to 820 MHz
820 to 835 MHz
912 to 927 MHz
927 to 972 MHz
972 to 1300 MHz
Source Impedance
Load Impedance
Temperature Coefficient of Frequency
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Electrical Connections
Connection
Terminals
Input
2
Output
5
Case Ground
All others
Value
+10
3
-45 to +125
-30 to +85
-40 to +85
260
Units
dBm
V
°C
°C
°C
°C
869.5 MHz
SAW Filter
SM3030-6
Sym
fC
IL
Notes
Min
Typ
869.5
2.5
0.8
1.6
Max
3.5
1.5
2.0
40 53
35 49
25 34
35 41
40 55
ZS 50
ZL 50
-36
SM3030-6 3.0 x 3.0 mm Nominal Footprint
6H, YWWS
500 Pieces/Reel
3000 Pieces/Reel
Units
MHz
dB
dBP-P
dB
ppm/k
SF2380E
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
NOTES:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd.
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. February 2015
SF2380E (R) 4/26/17
Page 1 of 5
www.murata.com


Murata Manufacturing Electronic Components Datasheet

SF2380E Datasheet

SAW Filter

No Preview Available !

Transfer Function
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. February 2015
SF2380E (R) 4/26/17
Page 2 of 5
www.murata.com


Part Number SF2380E
Description SAW Filter
Maker muRata
PDF Download

SF2380E Datasheet PDF






Similar Datasheet

1 SF2380E SAW Filter
muRata





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy