900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Murata Manufacturing Electronic Components Datasheet

SF2215E Datasheet

SAW Filter

No Preview Available !

• Low-loss 1960 MHz Filter
• Complies with Directive 2002/95/EC (RoHS)
Pb
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operable Temperature Range
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 5 cycles/10 seconds maximum
Value
+10
3
-45 to +125
-20 to +75
-40 to +85
265
Units
dBm
V
°C
°C
°C
°C
SF2215E
1960 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 1927.5 to 1992.5 MHz
Peak-to-Peak Amplitude Ripple, 1927.5 to 1992.5 MHz
Input/Output Return Loss, 1927.5 to 1992.5 MHz
Group Delay, 1927.5 to 1992.5 MHz
Attenuation, Referenced to 0 dB:
DC to 1740 MHz
1740 to 1801 MHz
1801 to 1880 MHz
2040 to 2120 MHz
2120 to 2500 MHz
3700 to 4000 MHz
Source Impedance
Load Impedance
Sym
fC
IL
Notes
Min
7.4
20
30
20
25
31
25
ZS
ZL
Typ
1960.0
2.7
1.3
2.5
25
31
36
41
40
38
32
50
50
SM3030-6
Max
4.0
2.5
Units
MHz
dB
dB
ns
dB
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 inch
Reel Size 13 inch
Electrical Connections
Connection
Terminals
Input
2
Output
5
Case Ground
All others
SM3030-6 3.0 x 3.0 mm Nominal Footprint
951, YWWS
500 Pieces/Reel
3000 Pieces/Reel
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
NOTES:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd.
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. March 2015
SF2215E (R) 6/7/17
Page 1 of 5
www.murata.com


Murata Manufacturing Electronic Components Datasheet

SF2215E Datasheet

SAW Filter

No Preview Available !

Filter Passband Response
Filter Broadband Response
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. March 2015
SF2215E (R) 6/7/17
Page 2 of 5
www.murata.com


Part Number SF2215E
Description SAW Filter
Maker muRata
PDF Download

SF2215E Datasheet PDF






Similar Datasheet

1 SF2215E SAW Filter
muRata





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy