900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Murata Manufacturing Electronic Components Datasheet

SF2201E Datasheet

SAW Filter

No Preview Available !

• Low-loss SAW Filter
• Surface Mount 3.0 x 3.0 x 1.3 mm Package
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operable Temperature Range
Specification Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 5 cycles/10 seconds maximum
Value
+17
5
-45 to +125
-30 to +85
-40 to +85
265
Units
dBm
V
°C
°C
°C
°C
RoHS Compliance
This component is compliant
with RoHS directive.
This component was always
RoHS compliant from the first
date of manufacture.
SF2201E
916.45 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 914.45 to 918.45 MHz
Amplitude Ripple, 914.45 to 918.45 MHz
VSWR, 914.45 to 918.45 MHz
Attenuation Referenced to 0 dB
DC to 600 MHz
600 to 840 MHz
869 to 894 MHz
970 to 1500 MHz
1500 to 3000 MHz
Source Impedance
Load Impedance
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Electrical Connections
Connection
Terminals
Input
2
Output
5
Ground
All Others
SM3030-6
Sym
FC
IL
Notes
Min
Typ
916.45
2.7
0.3
1.5:1
Max
3.5
1.0
2.0:1
50 57
40 51
35 46
40 47
25 32
ZS 50
ZL 50
SM3030-6 3.0 x 3.0 mm Nominal Footprint
931, YWWS
500 Pieces/Reel
3000 Pieces/Reel
Units
MHz
dB
dBP-P
dB
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
NOTES:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd.
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. February 2015
SF2201E (R) 7/10/18
Page 1 of 6
www.murata.com


Murata Manufacturing Electronic Components Datasheet

SF2201E Datasheet

SAW Filter

No Preview Available !

Filter Passband Response
Filter Test Circuit
50 ohm
5 SF2201E 2
1,3,4,6
50 ohm
©2010-2015 by Murata Electronics N.A., Inc.
SF2201E (R) 7/10/18
Page 2 of 6
www.murata.com


Part Number SF2201E
Description SAW Filter
Maker muRata
PDF Download

SF2201E Datasheet PDF






Similar Datasheet

1 SF2201E SAW Filter
muRata





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy