900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Pericom Semiconductor

PI3USB10 Datasheet Preview

PI3USB10 Datasheet

2:1 Mux/DeMux USB 2.0 Switch w/ Single Enable

No Preview Available !

Features
RON is 4Ω typical
• Low bit-to-bit skew: 200ps
• Low Crosstalk: –22dB @ 250MHz
• Near-Zero propagation delay: 250ps
• Switching speed: 9ns
• Channel On Capacitance: 6pF (typical)
• VCC Operating Range: +3.0V to +3.6V
• ESD>2000V . . . Human Body Model
• >500 MHz bandwidth (or data frequency)
• Packaging:
- Pb-free & Green,12-contact TDFN (ZE)
Application
• Routes signals for USB 2.0
Block Diagram
PI3USB10
3.3V, Wide Bandwidth, 2-Channel,
2:1 Mux/DeMux USB 2.0 Switch w/ Single Enable
Description
Pericom Semiconductor’s PI3USB series of logic circuits are
produced using the Company’s advanced sub-micron CMOS
technology, achieving industry leading performance.
The PI3USB10 is a 4- to 2-Channel multiplexer/demultiplexer
USB 2.0 Switch with Hi-Z outputs. Industry leading advantages
include a propagation delay of less than 250ps, resulting from its
low channel resistance and I/O capacitance. The device multi-
plexes differential outputs from a USB Host device to one of two
corresponding outputs. The switch is bidirectional and offers little
or no attenuation of the high-speed signals at the outputs. It is
designed for low bit-to-bit skew, high channel-to-channel noise
isolation and is compatible with various standards, such as High
Speed USB 2.0 (480 Mb/s).
Pin Description
Y0
Y1
SEL
GND 1
12 0l0
0I0
1I0
VDD
2
11 1I0
0I1
Y0 3
10 0I1
1I1
Y1 4
9 1I1
GND 5
8 VDD
SEL 6
7 GND
Truth Table
Function
Yn to nIo
Yn to nI1
SEL
L
H
1
PS8718
07/23/04




Pericom Semiconductor

PI3USB10 Datasheet Preview

PI3USB10 Datasheet

2:1 Mux/DeMux USB 2.0 Switch w/ Single Enable

No Preview Available !

PI3USB10
3.3V, Wide Bandwidth, 2-Channel,
2:1 Mux/DeMux USB 2.0 Switch
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ......................................... –65°C to +150°C
Supply Voltage to Ground Potential .................... –0.5V to +4.0V
DC Input Voltage ................................................. –0.5V to +5.5V
DC Output Current ........................................................... 120mA
Power Dissipation ................................................................ 0.5W
Note: Stresses greater than those listed under MAXIMUM RAT-
INGS may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
DC Electrical Characteristics for USB 2.0 Switching over Operating Range
(TA = –40°C to +85°C, VCC = 3.3V ±10%)
Paramenter
Description
Test
Conditions
Min.
VIH Input HIGH Voltage
Guaranteed HIGH level
2.0
VIL Input LOW Voltage
Guaranteed HIGH level
-5.0
VIK Clamp Diode Voltage
IIH Input HIGH Current
IIL Input LOW Current
VCC = Max., IIN = –18mA
VCC = Max., VIN = VCC
VCC = Max., VIN = GND
-
-
-
RON Switch On-Resistance(3)
VCC = Min., 1.25V ≤ VIN ≤ VCC,
IIN = –40mA
-
RFLAT(ON) On-Resistance Flatness(4)
VCC = Min., VIN @ 1.5V and
VCC IIN = -40mA
-
ΔRON
On-Resistance match from cen- VCC = Min., 1.5V ≤ VIN ≤ VCC,
ter ports to any other port(4)
IIN = -40mA
-
Type(2) Max.
--
- 0.8
-0.7 -1.2
- ±5
- ±5
48
Units
V
μA
1.0 -
0.9 2
Capacitance (TA = 25°C, f = 1MHz)
Parameters(4)
Description
Test Conditions Type
Max.
Units
CIN Input Capacitance
2.0 3.0
COFF
Port I Capacitance, Switch OFF
VIN = 0V
4.0 6.0
pF
CON Switch Capacitance, Switch ON
6.0 10.0
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading.
3. Measured by the voltage drop between A and B pins at indicated current through the switch. ON-resistance is determined by the lower of the
voltages on the two (A & B) pins.
4. This parameter is determined by device characterization but is not production tested.
2
PS8718
07/23/04


Part Number PI3USB10
Description 2:1 Mux/DeMux USB 2.0 Switch w/ Single Enable
Maker Pericom Semiconductor
PDF Download

PI3USB10 Datasheet PDF






Similar Datasheet

1 PI3USB10 3.3V/ Wide Bandwidth/ 2-Channel/ 2:1 Mux/DeMux USB 2.0 Switch w/ Single Enable
ETC
2 PI3USB10 2:1 Mux/DeMux USB 2.0 Switch w/ Single Enable
Pericom Semiconductor
3 PI3USB102 USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted
Pericom Semiconductor
4 PI3USB102E USB 2.0 High-Speed (480 Mbps) Switch
Pericom Semiconductor
5 PI3USB102G USB 2.0 High-Speed (480 Mbps) Switch
Pericom Semiconductor
6 PI3USB103 USB 2.0 High-Speed (480 Mbps) Signal Switch
Pericom Semiconductor Corporation
7 PI3USB10ZEE 3.3V/ Wide Bandwidth/ 2-Channel/ 2:1 Mux/DeMux USB 2.0 Switch w/ Single Enable
ETC
8 PI3USB14 Low Voltage High Bandwidth / USB 2.0 4:1 Mux/DeMux
Pericom Semiconductor
9 PI3USB14-A 4:1 Mux/DeMux
Pericom Semiconductor Corporation





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy