Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
Surface Mount Type
Series: ZK Type: V
High temperature lead-free reflow
UPGRADE
Features
● High capacitance and High ripple current compared with ZC series
● Endurance : 4000 h at 125 °C (High temperature / Long life)
● Low ESR (85 % over, Lower ESR than Current V-TP), Low LC (0.01 CV or 3 μA)
● Equivalent to conductive polymer type Aluminum Electrolytic Capacitor
(There are little characteristics change by temperature and frequency)
● Vibration-proof product is available upon request. New lineup of φ6.3 product.（φ6.3、φ8、φ10）
● AEC-Q200 compliant
● RoHS compliant
Specifications
Size code
C
D D8 F
G
Category temp. range
–55 ℃ to +125 ℃
Rated voltage range
25 V.DC to 35 V.DC
Nominal cap.range 33 μF to 47 μF 56 μF to 82 μF 100 μF to 150 μF 180 μF to 270 μF 330 μF to 470 μF
Capacitance tolerance
±20 % (120 Hz / +20 ℃)
DC leakage current
I ≦ 0.01 CV or 3 (μA) After 2 minutes (whichever is greater)
Dissipation factor (tan δ)
Please see the attached characteristics list
+125 °C ± 2 °C, 4000 h, apply the rated ripple current without exceeding the rated voltage.
Capacitance change Within ±30% of the initial value
Dissipation factor (tan δ) ≦ 200 % of the initial limit
Endurance
ESR
DC leakage current
≦ 200 % of the initial limit
Within the initial limit
ESR after Endurance
(Ω / 100 kHz)(-40 ℃）
C
2.0
Size code
D D8 F
1.4 0.8 0.4
G
0.3
After storage for 1000 hours at +125 °C ± 2 °C with no voltage applied and then being
Shelf life
stabilized at +20 °C, capacitors shall meet the limits specified in Endurance.
(With voltage treatment)
+85 °C ± 2 °C, 85 % to 90 %, 2000 h, rated voltage applied
Capacitance change Within ±30% of the initial value
Damp heat (Load) Dissipation factor (tan δ) ≦ 200 % of the initial limit
ESR ≦ 200 % of the initial limit
DC leakage current Within the initial limit
After reflow soldering and then being stabilized at +20 °C, capacitors shall meet the
Resistance to
soldering heat
following limits.
Capacitance change Within ±10% of the initial value
Dissipation factor (tan δ) Within the initial limit
DC leakage current Within the initial limit
Marking
Dimensions (not to scale)
Example : 25 V.DC 47 μF
Marking color : BLACK
Negative polarity marking (–)
0.3 max.
– A±0.2
47
E ZK
Capacitance (μF)
Series identification
Rated voltage mark
Lot number
Rated vol. mark
E
V
Unit：V.DC
25
35
L +W
Pressure relief (φ10 and larger)
( )Reference size
Unit：ｍｍ
Size code φD
C 5.0
D 6.3
D8 6.3
F 8.0
L A、B H
I
5.8±0.3 5.3 6.5 max. 2.2
5.8±0.3 6.6 7.8 max. 2.6
7.7±0.3 6.6 7.8 max. 2.6
10.2±0.3 8.3 10.0 max. 3.4
W
0.65±0.1
0.65±0.1
0.65±0.1
0.90±0.2
PK
1.5
0.35
+0.15
-0.20
1.8
0.35
+0.15
-0.20
1.8
0.35
+0.15
-0.20
3.1 0.70±0.2
G 10.0 10.2±0.3 10.3 12.0 max. 3.5 0.90±0.2 4.6 0.70±0.2
·The dimensions of the vibration-proof products, please refer to the page oft
he mounting specification.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
31-May-19
