900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Nichicon

PLE0G821MDO1 Datasheet Preview

PLE0G821MDO1 Datasheet

ALUMINUM ELECTROLYTIC CAPACITORS

No Preview Available !

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LE Radial Lead Type, Ultra-low ESR
series
Ultra-low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence
Compliant to the RoHS directive (2002/95/EC).
LF Low ESR
LE
Specifications
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 6.3V
Rated Capacitance Range 470 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions prescribed
here as preheat at 150 to 200°C for 60 to 180 seconds and peak
temperature at 265°C for 10 seconds or less, the capacitor shall meet
the specifications listed at right, provided that its temperature profile is
measured at both of terminal ends facing the soldering side.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Resin coated Case
Voltage(g:4V)
Silvered lead Wire
Type numbering system (Example : 4V 560µF)
1 2 3 4 5 6 7 8 9 10 11 12
P L E 0G 5 6 1 MCO 1
Series
Lot. No.
L+0.5MAX.
φd
15MIN
4MIN
Size φ8 × 9L
φD 8.0
L 8.5
P 3.5
φd 0.6
φ8 × 12L
8.0
11.5
3.5
0.6
(mm)
φ10 × 13L
10.0
12.5
5.0
0.6
Please refer to page 20 about the end seal configulation.
Voltage
V 2.5 4 6.3
Code
e
g
j
Size code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (560µF)
Rated voltage (4V)
Series name
Type
Dimension table in next page.
CAT.8100Z




Nichicon

PLE0G821MDO1 Datasheet Preview

PLE0G821MDO1 Datasheet

ALUMINUM ELECTROLYTIC CAPACITORS

No Preview Available !

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LE series
Standard Ratings
Rated Voltage
(V)
Code
Surge Voltage
(V)
Rated Capacitance
(µF)
560
2.5
(0E) 2.8
820
820
1000
1500
560
4
(0G)
4.6
680
820
1200
6.3
(0J) 7.2
470
680
820
Case Size
φD × L (mm)
8×9
8×9
8 × 12
10 × 13
10 × 13
8×9
8 × 12
10 × 13
10 × 13
8 × 12
10 × 13
10 × 13
tan δ
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
Leakage Current
(µA)
ESR (m)
(at 100kHz 20°C)
Rated Ripple
(mArms)
Part Number
280
410
410
500
750
448
544
656
960
592
857
1033
5
6100
PLE0E561MCO1
5
6300
PLE0E821MCO6
5
6600
PLE0E821MDO1
5
7100
PLE0E102MDO1
5
7300
PLE0E152MDO1
5
6000
PLE0G561MCO1
5
6500
PLE0G681MDO1
5
7000
PLE0G821MDO1
5
7200
PLE0G122MDO1
5
6400
PLE0J471MDO1
5
6700
PLE0J681MDO1
5
6800
PLE0J821MDO1
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
: In this case, 6 will be put at 12th digit of type numbering system.
Taping specifications are given in page 20, 21, 22.
Please refer to page 3 for the minimum order quantity.
CAT.8100Z


Part Number PLE0G821MDO1
Description ALUMINUM ELECTROLYTIC CAPACITORS
Maker Nichicon
PDF Download

PLE0G821MDO1 Datasheet PDF






Similar Datasheet

1 PLE0G821MDO1 ALUMINUM ELECTROLYTIC CAPACITORS
Nichicon





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy