900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




NXP Semiconductors Electronic Components Datasheet

PCA9306 Datasheet

Dual bidirectional I2C-bus and SMBus voltage-level translator

No Preview Available !

PCA9306
Dual bidirectional I2C-bus and SMBus voltage-level translator
Rev. 8 — 22 January 2014
Product data sheet
1. General description
The PCA9306 is a dual bidirectional I2C-bus and SMBus voltage-level translator with an
enable (EN) input, and is operational from 1.0 V to 3.6 V (Vref(1)) and 1.8 V to 5.5 V
(Vbias(ref)(2)).
The PCA9306 allows bidirectional voltage translations between 1.0 V and 5 V without the
use of a direction pin. The low ON-state resistance (Ron) of the switch allows connections
to be made with minimal propagation delay. When EN is HIGH, the translator switch is on,
and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively,
allowing bidirectional data flow between ports. When EN is LOW, the translator switch is
off, and a high-impedance state exists between ports.
The PCA9306 is not a bus buffer like the PCA9509 or PCA9517A that provide both level
translation and physically isolates the capacitance to either side of the bus when both
sides are connected. The PCA9306 only isolates both sides when the device is disabled
and provides voltage level translation when active.
The PCA9306 can also be used to run two buses, one at 400 kHz operating frequency
and the other at 100 kHz operating frequency. If the two buses are operating at different
frequencies, the 100 kHz bus must be isolated when the 400 kHz operation of the other
bus is required. If the master is running at 400 kHz, the maximum system operating
frequency may be less than 400 kHz because of the delays added by the translator.
As with the standard I2C-bus system, pull-up resistors are required to provide the logic
HIGH levels on the translator’s bus. The PCA9306 has a standard open-collector
configuration of the I2C-bus. The size of these pull-up resistors depends on the system,
but each side of the translator must have a pull-up resistor. The device is designed to work
with Standard-mode, Fast-mode and Fast-mode Plus I2C-bus devices in addition to
SMBus devices. The maximum frequency is dependent on the RC time constant, but
generally supports > 2 MHz.
When the SDA1 or SDA2 port is LOW, the clamp is in the ON-state and a low resistance
connection exists between the SDA1 and SDA2 ports. Assuming the higher voltage is on
the SDA2 port when the SDA2 port is HIGH, the voltage on the SDA1 port is limited to the
voltage set by VREF1. When the SDA1 port is HIGH, the SDA2 port is pulled to the drain
pull-up supply voltage (Vpu(D)) by the pull-up resistors. This functionality allows a
seamless translation between higher and lower voltages selected by the user without the
need for directional control. The SCL1/SCL2 channel also functions as the SDA1/SDA2
channel.


NXP Semiconductors Electronic Components Datasheet

PCA9306 Datasheet

Dual bidirectional I2C-bus and SMBus voltage-level translator

No Preview Available !

NXP Semiconductors
PCA9306
Dual bidirectional I2C-bus and SMBus voltage-level translator
All channels have the same electrical characteristics and there is minimal deviation from
one output to another in voltage or propagation delay. This is a benefit over discrete
transistor voltage translation solutions, since the fabrication of the switch is symmetrical.
The translator provides excellent ESD protection to lower voltage devices, and at the
same time protects less ESD-resistant devices.
2. Features and benefits
2-bit bidirectional translator for SDA and SCL lines in mixed-mode I2C-bus applications
Standard-mode, Fast-mode, and Fast-mode Plus I2C-bus and SMBus compatible
Less than 1.5 ns maximum propagation delay to accommodate Standard-mode and
Fast-mode I2C-bus devices and multiple masters
Allows voltage level translation between:
1.0 V Vref(1) and 1.8 V, 2.5 V, 3.3 V or 5 V Vbias(ref)(2)
1.2 V Vref(1) and 1.8 V, 2.5 V, 3.3 V or 5 V Vbias(ref)(2)
1.8 V Vref(1) and 3.3 V or 5 V Vbias(ref)(2)
2.5 V Vref(1) and 5 V Vbias(ref)(2)
3.3 V Vref(1) and 5 V Vbias(ref)(2)
Provides bidirectional voltage translation with no direction pin
Low 3.5 ON-state connection between input and output ports provides less signal
distortion
Open-drain I2C-bus I/O ports (SCL1, SDA1, SCL2 and SDA2)
5 V tolerant I2C-bus I/O ports to support mixed-mode signal operation
High-impedance SCL1, SDA1, SCL2 and SDA2 pins for EN = LOW
Lock-up free operation
Flow through pinout for ease of printed-circuit board trace routing
ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per
JESD22-C101
Packages offered: SO8, TSSOP8, VSSOP8, XQFN8, XSON8, XSON8U
PCA9306
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 22 January 2014
© NXP B.V. 2014. All rights reserved.
2 of 35


Part Number PCA9306
Description Dual bidirectional I2C-bus and SMBus voltage-level translator
Maker NXP Semiconductors
PDF Download

PCA9306 Datasheet PDF






Similar Datasheet

1 PCA9306 SMBus Voltage-Level Translator
etcTI
2 PCA9306 Dual bidirectional I2C-bus and SMBus voltage-level translator
NXP Semiconductors
3 PCA9306 Dual Bidirectional I2C-bus and SMBus Voltage-Level Translator
ON Semiconductor
4 PCA9306-Q1 SMBus Voltage-Level Translator
etcTI





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy