900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




NXP Semiconductors Electronic Components Datasheet

P89LPC908 Datasheet

8-bit microcontrollers

No Preview Available !

P89LPC906/907/908 www.DataSheet4U.com
8-bit microcontrollers with two-clock 80C51 core
1 kB 3 V Flash with 128-byte RAM
Rev. 05 — 17 December 2004
Product data
1. General description
The P89LPC906/907/908 are single-chip microcontrollers in low-cost 8-pin packages,
based on a high performance processor architecture that executes instructions in two
to four clocks, six times the rate of standard 80C51 devices. Many system-level
functions have been incorporated into the P89LPC906/907/908 in order to reduce
component count, board space, and system cost.
2. Features
2.1 Principal features
s 1 kB byte-erasable Flash code memory organized into 256-byte sectors and
16-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile
data storage.
s 128-byte RAM data memory.
s Two 16-bit counter/timers. (Timer 0 may be configured to toggle a port output
upon timer overflow or to become a PWM output on the P89LPC907 device).
s 23-bit system timer that can also be used as a Real-Time clock.
s A single analog comparator with selectable reference source.
s Enhanced UART with fractional baudrate generator, break detect, framing error
detection, automatic address detection and versatile interrupt capabilities
(P89LPC908, transmit only on P89LPC907).
s Internal RC oscillator option (factory calibrated to ±1 %) allows operation without
external oscillator components. The RC oscillator option is selectable and fine
tunable.
s 2.4 V to 3.6 V VDD operating range with 5 V tolerant I/O pins (may be pulled up or
driven to 5.5 V). Supply pins located at package centers for improved supply
decoupling and reduced EMI.
s Up to six I/O pins when using internal oscillator and reset options.
s 8-pin SO-8 package.
2.2 Additional features
s A high performance 80C51 CPU provides instruction cycle times of 111 ns to
222 ns for all instructions except multiply and divide when executing at 18 MHz
(P89LPC906) (167 ns to 333 ns at 12 MHz). This is six times the performance of
the standard 80C51 running at the same clock frequency. A lower clock frequency
for the same performance results in power savings and reduced EMI.
s In-Application Programming (IAP-Lite) and byte erase allows code memory to be
used for non-volatile data storage.


NXP Semiconductors Electronic Components Datasheet

P89LPC908 Datasheet

8-bit microcontrollers

No Preview Available !

Philips Semiconductors
P89LPC906/907/908
8-bit microcontrollers with twwow-cwlo.Dcakta8S0hCee5t14Uc.coorem
s Serial Flash In-Circuit Programming (ICP) allows simple production coding with
commercial EPROM programmers. Flash security bits prevent reading of sensitive
application programs.
s Watchdog timer with separate on-chip oscillator, requiring no external
components. The watchdog prescaler is selectable from 8 values.
s Low voltage reset (Brownout detect) allows a graceful system shutdown when
power fails. May optionally be configured as an interrupt.
s Idle and two different Power-down reduced power modes. Improved wake-up from
Power-down mode (a low interrupt input starts execution). Typical Power-down
current is 1 µA (total Power-down with voltage comparators disabled).
s Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A reset counter and reset glitch suppression circuitry prevent
spurious and incomplete resets. A software reset function is also available.
s Configurable on-chip oscillator with frequency range options selected by user
programmed Flash configuration bits. Oscillator options support frequencies from
20 kHz to the maximum operating frequency of 18 MHz (P89LPC906).
s Programmable port output configuration options: quasi-bidirectional, open drain,
push-pull, input-only.
s Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value
of the pins match or do not match a programmable pattern.
s LED drive capability (20 mA) on all port pins. A maximum limit is specified for the
entire chip.
s Controlled slew rate port outputs to reduce EMI. Outputs have approximately
10 ns minimum ramp times.
s Only power and ground connections are required to operate the
P89LPC906/907/908 when internal reset option is selected.
s Four interrupt priority levels.
s Three keypad interrupt inputs.
s Second data pointer.
s Schmitt trigger port inputs.
s Emulation support.
9397 750 14467
Product data
Rev. 05 — 17 December 2004
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
2 of 51


Part Number P89LPC908
Description 8-bit microcontrollers
Maker NXP Semiconductors
PDF Download

P89LPC908 Datasheet PDF






Similar Datasheet

1 P89LPC901 8-bit microcontrollers
NXP
2 P89LPC902 8-bit microcontrollers
NXP
3 P89LPC903 8-bit microcontrollers
NXP
4 P89LPC904 8-bit microcontrollers
NXP Semiconductors
5 P89LPC906 8-bit microcontrollers
NXP Semiconductors
6 P89LPC907 8-bit microcontrollers
NXP Semiconductors
7 P89LPC908 8-bit microcontrollers
NXP Semiconductors





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy