900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






MA-COM

MASWSS0192 Datasheet Preview

MASWSS0192 Datasheet

GaAs SPDT Switch

No Preview Available !

MASWSS0192
GaAs SPDT Switch
DC - 3.0 GHz
Features
Test and Measurement and Low/Medium Power
Telecommunication Applications
Low Insertion Loss: 0.18 dB @ 1 GHz
Moderate Isolation: 25 dB @ 1 GHz
Low Power Consumption: < 2 μA @ 2.5 V
Fast Settling for Low Gate Lag Requirements
Lead-Free SC-70 (SOT-363) Package
100% Matte Tin Plating over Copper
Halogen-Free ―Green‖ Mold Compound
RoHS* Compliant and 260°C Reflow Compatible
Description
M/A-COM’s MASWSS0192 is a GaAs PHEMT
MMIC SPDT switch in a lead-free SC-70 (SOT-363)
surface mount plastic package. The MASWSS0192
is ideally suited for applications where very small
size and low cost are required.
The MASWSS0192 can be used for low / medium
power, low loss requirements in all systems
operating up to 3 GHz, including PCS, GSM, DCS,
Blue Tooth, T&M, and other receive chain applica-
tions.
The MASWSS0192 is fabricated using a 0.5 micron
gate length GaAs PHEMT process. The process
features full passivation for performance and
reliability.
Ordering Information 1
Part Number
Package
MASWSS0192
Bulk Packaging
MASWSS0192TR-3000
3000 piece reel
MASWSS0192SMB
Sample Board
1. Reference Application Note M513 for reel size information.
Functional Schematic
C=39pF
V1
RFC
V2
Rev. V1
RF1
PIN 1
GND
C=39pF
RF2
C=39pF
Pin Configuration
Pin No.
1
2
3
4
5
6
Pin Name
RF1
GND
RF2
V2
RFC
V1
Description
RF Port 1
Ground
RF Port 2
Control 2
RF Input
Control 1
Absolute Maximum Ratings 2,3
Parameter
Absolute Maximum
Input Power (0.5 - 3.0 GHz)
2.5 V Control
5.0 V Control
Operating Voltage
+25 dBm
+34 dBm
+8.5 volts
Operating Temperature
-40 °C to +85 °C
Storage Temperature
-65 °C to +150 °C
2. Exceeding any one or combination of these limits may
cause permanent damage to this device.
3. M/A-COM does not recommend sustained operation near
these survivability limits.
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
1
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support




MA-COM

MASWSS0192 Datasheet Preview

MASWSS0192 Datasheet

GaAs SPDT Switch

No Preview Available !

MASWSS0192
GaAs SPDT Switch
DC - 3.0 GHz
Rev. V1
Electrical Specifications: TA = 25°C, VC = 0 V / 2.5 V 4, PIN = +10 dBm, Z0 = 50 5
Parameter
Insertion Loss 6
Isolation
VSWR
IP2
Test Conditions
DC - 1.0 GHz
DC - 3.0 GHz
DC - 1.0 GHz
DC - 3.0 GHz
DC - 1.0 GHz
DC - 3.0 GHz
1 GHz, Two Tone, +7 dBm / tone, 20 MHz Spacing, 3 V
Units
dB
dB
dB
dB
Ratio
Ratio
dBm
Min.
20.0
9.5
Typ.
0.18
0.35
24.0
13.5
1.1:1
1.2:1
93
Max.
0.40
0.60
IP3
1 GHz, Two Tone, +7 dBm / tone, 20 MHz Spacing, 3 V
dBm 53
P1dB
Trise, Tfall
VC = 0.2 V / 2.7 V
VC = 0.2 V / 3.0 V
10% to 90% RF and 90% to 10% RF
dBm
dBm
nS
27.5
28.5
22
Ton, Toff
50% control to 90% RF, 50% control to 10% RF
nS 5
Transients
In-band
mV 36
Control Current
— µA — 0.20 5
RON
Gate Lag
t > 90 mS after OFF to ON Switching (settled)
|ΔRon| between 15 µS and 90 mS after OFF to ON Switching
Ω
Ω
2.50 4.7
0.15 0.7
4. Alternate voltage operation of VC = 0 V / 5 V or -5 V / 0 V will yield similar insertion loss, isolation, VSWR, switching, RON, and gate lag
results.
5. For positive voltage control, external DC blocking capacitors are required on all RF ports.
6. Insertion loss can be optimized by varying the DC blocking capacitor value, e.g. 1000 pF for 100 MHz - 1 GHz, 39 pF for 0.5 - 3 GHz.
Truth Table 7,8
Control
V1
Control
V2
RFC-RF1 RFC-RF2
1 0 On Off
0 1 Off On
7. Differential voltage, V (state 1) - V (state 0), must be 2.5 V
minimum, but must not exceed 8.5 V.
8. 0 = 0 V to 0.5 V; 1 = 2.5 V to 5 V or
0 = -5 V to -2.5 V, 1 = -0.5 to 0 V.
Qualification
Qualified to M/A-COM specification REL-201,
Process Flow 2.
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
2
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support


Part Number MASWSS0192
Description GaAs SPDT Switch
Maker MA-COM
PDF Download

MASWSS0192 Datasheet PDF






Similar Datasheet

1 MASWSS0190 GaAs Broadband DPDT Diversity Switch
Tyco Electronics
2 MASWSS0191 GaAs SP3T 2.6 V CDMA-GPS Switch
Tyco Electronics
3 MASWSS0192 GaAs SPDT Switch
Tyco Electronics
4 MASWSS0192 GaAs SPDT Switch
MA-COM
5 MASWSS0199 GaAs SP3T 2.6 V CDMA-GPS Switch
Tyco Electronics





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy