Pl tronics, Inc.
.19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
PVB, PVM PECL VCXO Series
Differential PECL Output with Enable/Disable
6 Pad Leadless Surface Mount or
4 Lead Thru-Hole PECL Voltage Controlled Xtal Oscillator
1.00 MHz – 650.00 MHz
Consult factory for higher frequencies
Standard Specifications
Overall Frequency Stability
Operating Temperature Range
Storage Temperature Range
Supply Voltage (Vcc)
Supply Current (Icc)
Output High Level
Output Low Level
± 50 PPM, ± 25 PPM, ± 20 PPM over Operating Temperature Range
0 to +70°C is standard, but can be extended to - 40 to +85°C
- 55 to +125°C
3.3 volts ± 5% standard, but 5.0 volts or 2.5 volts also available. See Test Cirucit 5.
< 250 MHz = 90 mA maximum, 250 MHz and above = 100 mA maximum
2.275 V minimum referenced to Ground, Vcc = 3.300V,
0.975 V minimum referenced to termination voltage,
- 1.025 V minimum referenced to Vcc
1.680 V maximum referenced to Ground, Vcc = 3.300V,
0.380 V maximum referenced to termination voltage,
- 1.620 V maximum referenced to Vcc
Output Symmetry
Output Rise & Fall (Tr & Tf)
Jitter
E/D Internal Pullup
V disable
V enable
Linerarity
Slope
Control Voltage Range (CVR)
Pullability
PVB Output Enable/Disable (E/D)
Output Enable Time
Output Disable Time
When Disabled
45/55% referenced to 50% of amplitude
1.0 nS maximum when Vth is 10% and 90% of waveform
6 pS RMS maximum measured from 12 kHz to 20 MHz from output frequency
50 kohm minimum to Vcc
0.3 Vcc maximum referenced to Ground
0.7 Vcc minumum referenced to Ground
± 10% typical
Positive and montonic
For 5.0 Vcc, CVR = 0.5 to 4.5 V, For 3.3 Vcc, CVR = 0.0 to 3.3 V, For 2.5 Vcc, CVR = 0.0 to 2.5 V
Pull range is defined as absolute pull range. This is the pull range about the specified oscillator frequency,
independent of supply, temperature range and load. Typical values are ± 25, ± 50 and ± 100 PPM.
100 nS maximum
100 nS maximum
Q Output = Logic Low, QN Output = Logic High. Both Outputs are active
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
Packaging
PVM = Tube
PVB = Tube or
24mm tape
16mm pitch
PVB 5 V
Model
PVB = B Pkg
PVM = Metal
Frequency Stability
5 = ± 50 PPM
4 = ± 25 PPM
2 = ± 20 PPM
Supply Voltage
Y = 5.0 volts ±10%
V = 3.3 volts ±5%
W = 2.5 volts ±5%
B V - 100.0M - XXX (Internal Code or blank)
Frequency in MHz
Frequency Deviation (Pullability) Absolute Pull Range
V: ± 50 PPM
W = ± 100 PPM
Operating Temperature Range
B: 0 to +70°C
F: - 40 to +85°C
Mar 2004
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Pl tronics, Inc. (425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
20
