900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf




Cypress Semiconductor Electronic Components Datasheet

PLDC20RA10 Datasheet

Reprogrammable Asynchronous CMOS Logic Device

No Preview Available !

PLDC20RA10
Reprogrammable Asynchronous
CMOS Logic Device
1PLDC20RA10
Features
• Advanced-user programmable macrocell
CMOS EPROM technology for reprogrammability
Up to 20 input terms
10 programmable I/O macrocells
Output macrocell programmable as combinatorial or
asynchronous D-type registered output
Product-term control of register clock, reset and set and
output enable
Register preload and power-up reset
Four data product terms per output macrocell
Fast
Commercial
tPD = 15 ns
tCO = 15 ns
tSU = 7 ns
Military
tPD = 20 ns
tCO = 20 ns
tSU = 10 ns
Low power
ICC max - 80 mA (Commercial)
ICC max = 85 mA (Military)
High reliability
Proven EPROM technology
>2001V input protection
100% programming and functional testing
Windowed DIP, windowed LCC, DIP, LCC, PLCC avail-
able
Functional Description
The Cypress PLDC20RA10 is a high-performance, sec-
ond-generation programmable logic device employing a flexi-
ble macrocell structure that allows any individual output to be
configured independently as a combinatorial output or as a
fully asynchronous D-type registered output.
The Cypress PLDC20RA10 provides lower-power operation
with superior speed performance than functionally equivalent
bipolar devices through the use of high-performance 0.8-mi-
cron CMOS manufacturing technology.
The PLDC20RA10 is packaged in a 24 pin 300-mil molded
DIP, a 300-mil windowed cerDIP, and a 28-lead square lead-
less chip carrier, providing up to 20 inputs and 10 outputs.
When the windowed device is exposed to UV light, the 20RA10
is erased and can then be reprogrammed.
www.DataSheet.net/
Logic Block Diagram
VSS I9
12 11
I8 I7
10 9
I 6 I5
87
I 4 I 3 I2 I1
65
43
I 0 PL
21
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
MACROCELL MACROCELL MACROCELL MACROCELL MACROCELL MACROCELL MACROCELL MACROCELL MACROCELL MACROCELL
13 14 15 16 17 18 19 20 21 22 23 24
OE I/O9 I/O8 I/O7 I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 I/O0 VCC
RA101
Cypress Semiconductor Corporation • 3901 North First Street • San Jose • CA 95134 • 408-943-2600
Document #: 38-03012 Rev. **
Revised March 26, 1997
Datasheet pdf - http://www.DataSheet4U.co.kr/


Cypress Semiconductor Electronic Components Datasheet

PLDC20RA10 Datasheet

Reprogrammable Asynchronous CMOS Logic Device

No Preview Available !

PLDC20RA10
Selection Guide
Generic Part
Number
20RA10-15
20RA10-20
20RA10-25
20RA10-35
tPD ns
Coml
Mil
15
20 20
25
35
Pin Configurations
LCC
Top View
tSU ns
Coml
Mil
7
10 10
15
20
STD PLCC/HLCC
Top View
tCO ns
Coml
Mil
15
20 20
25
35
tCC ns
Coml
Mil
80
80 85
85
85
[1]
JEDEC PLCC/HLCC
Top View
4 3 2 1 282726
I2 5
25
I3 6
24
I4 7
23
I5 8 PLDC20RA10 22
II67
9
10
NC 11
21
20
19
12131415161718
NC
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
4 3 2 1 2827 26
NC 5
25
I3 6
24
I4
NC
7 23
8 PLDC20RA10 22
I5 9
I6 10
21
20
NC 11 121314 1516 1718 19
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
NC
4 3 2 1 2827 26
I2 5
25
I3 6
24
I4
NC
7 23
8 PLDC20RA10 22
I5 9 CG7C324 21
I6 10
20
I7
11
121314
1516 1718 19
I/O 2
I/O 3
I/O 4
NC
I/O 5
I/O 6
I/O 7
RA102
RA103
RA104
Macrocell Architecture
Figure 1 illustrates the architecture of the 20RA10 macrocell.
The cell dedicates three product terms for fully asynchronous
control of the register set, reset, and clock functions, as well
as, one term for control of the output enable function.
The output enable product term output is ANDed with the input
from pin 13 to allow either product term or hardwired external
control of the output or a combination of control from both
sources. If product-term-only control is selected, it is automat-
ically chosen for all outputs since, for this case, the external
output enable pin must be tied LOW. The active polarity of
each output may be programmed independently for each out-
put cell and is subsequently fixed. Figure 2 illustrates the out-
put enable options available.
When an I/O cell is configured as an output, combinatorial-only
capability may be selected by forcing the set and reset product
term outputs to be HIGH under all input conditions. This is
achieved by programming all input term programming cells for
these two product terms. Figure 3 illustrates the available out-
put configuration options.
An additional four uncommitted product terms are provided in
each output macrocell as resources for creation of user-de-
fined logic functions.
Programmable I/O
Because any of the ten I/O pins may be selected as an input,
the device input configuration programmed by the user may
vary from a total of nine programmable plus ten dedicated in-
puts (a total of nineteen inputs) and one output down to a
ten-input, ten-output configuration with all ten programmable
I/O cells configured as outputs. Each input pin available in a
given configuration is available as an input to the four control
product terms and four uncommitted product terms of each
programmable I/O macrocell that has been configured as an
output.
An I/O cell is programmed as an input by tying the output en-
able pin (pin 13) HIGH or by programming the output enable
productwww.DataSheet.net/ term to provide a LOW, thereby disabling the output
buffer, for all possible input combinations.
When utilizing the I/O macrocell as an output, the input path
functions as a feedback path allowing the output signal to be
fed back as an input to the product term array. When the output
cell is configured as a registered output, this feedback path
may be used to feed back the current output state to the device
inputs to provide current state control of the next output state
as required for state machine implementation.
Preload and Power-Up Reset
Functional testability of programmed devices is enhanced by
inclusion of register preload capability, which allows the state
of each register to be set by loading each register from an
external source prior to exercising the device. Testing of com-
plex state machine designs is simplified by the ability to load
an arbitrary state without cycling through long test vector se-
quences to reach the desired state. Recovery from illegal
states can be verified by loading illegal states and observing
recovery. Preload of a particular register is accomplished by
impressing the desired state on the register output pin and
lowering the signal level on the preload control pin (pin1) to a
logic LOW level. If the specified preload set-up, hold and pulse
width minimums have been observed, the desired state is
loaded into the register. To insure predictable system initializa-
tion, all registers are preset to a logic LOW state upon pow-
er-up, thereby setting the active LOW outputs to a logic HIGH.
Note:
1. The CG7C324 is the PLDC20RA10 packaged in the JEDEC-compatible 28-pin PLCC pinout. Pin function and pin order is identical for both PLCC pinouts. The
principal difference is in the location of the no connect(NC) pins
Document #: 38-03012 Rev. **
Page 2 of 14
Datasheet pdf - http://www.DataSheet4U.co.kr/


Part Number PLDC20RA10
Description Reprogrammable Asynchronous CMOS Logic Device
Maker Cypress
PDF Download

PLDC20RA10 Datasheet PDF






Similar Datasheet

1 PLDC20RA10 Reprogrammable Asynchronous CMOS Logic Device
Cypress





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z



Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy