900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






Agere Systems

L9313 Datasheet Preview

L9313 Datasheet

Line Interface and Line Access Circuit Full-Feature SLIC and Ringing

No Preview Available !

Data Sheet
September 2001
L9313 Line Interface and Line Access Circuit
Full-Feature SLIC and Ringing Relay for TR-57 Applications
Introduction
The Agere Systems Inc. L9313 is a combination full-
feature, ultralow-power SLIC, solid-state ringing
access relay, and line test matrix. It is part of a pin-
for-pin compatible family of devices designed to
serve a wide variety of applications. The L9313 is
optimized for TR-57 applications where forward and
reverse battery and ground start are required.
Features
SLIC
s 5 V and battery operation
s Optional automatic battery switch
s Seven operational modes
s Appropriate for 58 dB longitudinal balance applica-
tions
s Minimal external components required at all inter-
faces
s Ultralow power dissipation
s Software/hardware adjustable dc parameters and
supervision thresholds
s Ground start compatible
Description
The L9313 electronic line interface and line access
circuit (LILAC) provides all the functions that are nec-
essary to interface a codec to the tip and ring of a
subscriber loop, integrating the battery feed and ring-
ing access relay in one low-power, low-cost package.
The L9313 requires a 5 V and battery supply to oper-
ate. Included is an automatic battery switch. The bat-
tery feed offers forward and reverse battery, on-hook
transmission, and ground start operational modes. It
also has a low-power scan and a disconnect mode.
In all operating states, this IC is designed for minimal
power dissipation. This device is designed to mini-
mize the number of external components required at
all interfaces.
The dc template, current limit, and overhead voltage
and loop supervision threshold are programmable via
an applied voltage source. The voltage source may
be an external programmable voltage source or
derived from the VREF SLIC output.
The integrated solid-state switch offers power ringing
access. Impulse noise is minimized, thus eliminating
the need for external zero-cross switching circuitry.
Solid-State Ring Relay
s Low impulse noise
s Current-limited switches/thermal protection
Applications
s Pair Gain
s Digital Loop Carrier (DLC)
s Central Office (CO)
s Fiber-in-the-Loop (FITL)




Agere Systems

L9313 Datasheet Preview

L9313 Datasheet

Line Interface and Line Access Circuit Full-Feature SLIC and Ringing

No Preview Available !

L9313 Line Interface and Line Access Circuit
Full-Feature SLIC and Ringing Relay for TR-57 Applications
Data Sheet
September 2001
Table of Contents
Contents
Page Contents
Page
Introduction ..................................................................1
Features ....................................................................1
SLIC .......................................................................1
Solid-State Ring Relay ...........................................1
Applications...............................................................1
Description ................................................................1
Features ......................................................................4
Description...................................................................4
Architecture .................................................................7
Pin Information ............................................................8
Operating States........................................................10
Input State Coding ..................................................10
State Definitions ........................................................11
Primary Control Modes ...........................................11
Powerup, Forward Battery....................................11
Powerup, Reverse Battery ...................................11
Scan .....................................................................11
Ground Start.........................................................12
Ringing .................................................................12
Disconnect—Break Before Make .........................12
Tip Amp ................................................................12
Ring Amp .............................................................12
Reset ....................................................................12
Special States .........................................................12
Thermal Shutdown ...............................................12
Battery Out of Range ...........................................12
Absolute Maximum Ratings ......................................13
Electrical Characteristics ...........................................14
Ring Trip Detector ...................................................15
SLIC Two-Wire Port ................................................16
Analog Pin Characteristics ......................................17
ac Feed Characteristics ..........................................18
Logic Inputs and Outputs, VCC = 5.0 V ...................19
Timing Requirements ..............................................19
Switch Characteristics.............................................20
On-State Switch I-V Characteristics........................21
Test Configurations ...................................................22
Applications ...............................................................24
dc Characteristics ...................................................24
Power Control.......................................................24
Power Derating.....................................................24
Automatic Battery Switch .................................... 25
Power Control Resistor ....................................... 25
Overhead Voltage ............................................... 26
dc Loop Current Limit .......................................... 27
Loop Range......................................................... 27
Battery Feed........................................................ 27
Battery Reversal Rate ......................................... 28
Longitudinal to Metallic Balance.......................... 28
Supervision............................................................... 29
Loop Closure.......................................................... 29
Ring Trip ................................................................ 29
Ring Ground Detector ............................................ 29
Switching Behavior................................................. 29
Make-Before-Break Operation ............................... 29
Break-Before-Make Operation ............................... 30
Protection ................................................................. 30
External Protection................................................. 30
Active Mode Response at PT/PR........................... 31
Ring Mode Response at PT/PR ............................. 31
Internal Tertiary Protection..................................... 32
Diode Bridge........................................................ 32
Battery Out of Range Detector: High
(Magnitude) ................................................. 32
Battery Out of Range Detector: Low
(Magnitude) ................................................. 32
ac Applications ......................................................... 32
ac Parameters........................................................ 32
Codec Types .......................................................... 32
First-Generation Codecs ..................................... 33
Third-Generation Codecs .................................... 33
ac Interface Network .............................................. 33
Design Tools .......................................................... 34
First-Generation Codec ac Interface Network........ 34
First-Generation Codec ac Interface
Network: Resistive Termination ................... 35
Example 1, Real Termination .............................. 35
Third-Generation Codec ac Interface
Network: Complex Termination ................... 38
Outline Diagram........................................................ 40
Ordering Information................................................. 40
2 Agere Systems Inc.


Part Number L9313
Description Line Interface and Line Access Circuit Full-Feature SLIC and Ringing
Maker Agere Systems
Total Page 30 Pages
PDF Download

L9313 Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 L9310 Line Interface and Line Access Circuit Full-Feature SLIC/Ringing Relay and Test Access Device
Agere Systems
2 L9311 Line Interface and Line Access Circuit Full-Feature SLIC
Agere Systems
3 L9312 Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay
Agere Systems
4 L9313 Line Interface and Line Access Circuit Full-Feature SLIC and Ringing
Agere Systems





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy