900,000+ datasheet pdf search and download

Datasheet4U offers most rated semiconductors data sheet pdf






3Peak

TP1562A Datasheet Preview

TP1562A Datasheet

Op Amps

No Preview Available !

3PEAK
Features
TP1561A/ TP1561NA/TP1562A/TP1564A
Stable 6MHz, 500μA, RRIO, Precision, Op Amps
Description
Stable 6 MHz GBWP in VCM from 0V to VS
Excellent EMI Suppress Performance
Offset Voltage: ±400 μV Maximum
Offset Voltage Temperature Drift: 1 μV/°C
Input Bias Current: 1 pA Typical
THD+Noise: -115 dB at 1kHz, -99 dB at 10kHz
High CMRR/PSRR: 110/95 dB
Beyond the Rails Input Common-Mode Range
Outputs Swing to within 3 mV of Each Rail
No Phase Reversal for Overdriven Inputs
High Output Capability: 100mA
Shutdown Current: 0.2 μA (TP1561NA)
Supply Voltage Range:
- Single +2.1 V to +6.0 V Supply
- Or Dual ±1.05 V to ±3.0 V Supplies
40°C to 125°C Operation Temperature Range
ESD Rating: 8KV HBM, 2KVCDM and 500VMM
Green, Popular Type Package
Applications
The TP156xA series are CMOS single, dual, and
quad RRIO op-amps with low offset, low power and
stable high frequency response. They incorporate
3PEAKs proprietary and patented design
techniques to achieve very good AC performance
with 6MHz bandwidth, 4.5V/μs slew rate and low
distortion while drawing only 500μA of quiescent
current per amplifier. The input common-mode
voltage range extends 300mV beyond Vand V+,
and the outputs swing rail-to-rail. The TP156xA
family can be used as plug-in replacements for
many commercially available op-amps to reduce
power and improve input/output range and
performance.
The TP156xA Op-amps are unity gain stable with
any capacitive load. They operate from either single
+2.1V to +6.0V supply or dual ±1.05V to ±3.0V
supplies. Analog trim and calibration routine reduce
input offset voltage to below 400μV, and proprietary
precision temperature compensation technique
makes offset voltage temperature drift at 1μV/°C.
Adaptive biasing and dynamic compensation
enables the TP156xA to achieve „THD +Noisefor
1kHz/10kHz 2VPP signal at -115dB/ -99dB. Beyond
the rails input and rail-to-rail output characteristics
allow the full power-supply voltage to be used for
signal range.
Multimedia Audio
Headphone Drivers
LCD Drivers
Photo Diode Pre-amp
Medical Equipments
Portable Devices
ASIC Input or Output
Sensor Interfaces
The combination of features makes the TP156xA
ideal choices for audio amplification of computers,
sound ports, and other consumer Audio. The
TP156xA Op-amp is very stable, and it is capable of
driving heavy capacitive loads such as those found
in LCDs. The ability to swing rail-to-rail at the inputs
and outputs enables designers to buffer CMOS
DACs, ASICs, or other wide output swing devices in
single-supply systems.
3PEAK and the 3PEAK logo are registered trademarks of
3PEAK INCORPORATED. All other trademarks are the property
of their respective owners.
Pin Configuration (Top View)
TP1561A
5-Pin SOT23/SC70
-T and -C Suffixes
Out
Vs
1
2
5 Vs
TP1562A
8-Pin SOIC/TSSOP/MSOP
-S, -T and -V Suffixes
+In 3
4 -In
Out A 1
8 Vs
TP1561NA
6-Pin SOT23
(-T Suffix)
In A 2
In A 3
Vs 4
A
B
7 Out B
6 In B
5 In B
Out 1
Vs 2
+In 3
6 Vs
5 SHDN
4 -In
TP1564A
14-Pin SOIC/TSSOP
-S and -T Suffixes
Out A 1
In A 2
In A 3
Vs 4
In B 5
In B 6
Out B 7
A
B
14 Out D
13 In D
D
12 In D
11 Vs
10 In C
C
9 In C
8 Out C
www.3peakic.com.cn
Rev. B.03
1




3Peak

TP1562A Datasheet Preview

TP1562A Datasheet

Op Amps

No Preview Available !

TP1561A/ TP1561NA/TP1562A/TP1564A
Stable 6MHz, 500μA, RRIO, Precision Op Amps
Absolute Maximum Ratings Note 1
Supply Voltage: V+ V.......................................7V
Input Voltage............................. V0.3 to V+ + 0.3
Differential Input Voltage................................ ...±7V
Input Current: +IN, IN, SHDN Note 2.............. ±20mA
SHDN Pin Voltage……………………………Vto V+
Output Short-Circuit Duration Note 3............ Infinite
Operating Temperature Range.......40°C to 125°C
Maximum Junction Temperature................... 150°C
Storage Temperature Range.......... 65°C to 150°C
Lead Temperature (Soldering, 10 sec) ......... 260°C
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any
Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.
Note 2: The inputs are protected by ESD protection diodes to each power supply. If the input extends more than 300mV beyond the power
supply, the input current should be limited to less than 10mA.
Note 3: A heat sink may be required to keep the junction temperature below the absolute maximum. This depends on the power supply
voltage and how many amplifiers are shorted. Thermal resistance varies with the amount of PC board metal connected to the package. The
specified values are for short traces connected to the leads.
ESD, Electrostatic Discharge Protection
Symbol
HBM
MM
CDM
Parameter
Human Body Model ESD
Machine Model ESD
Charged Device Model ESD
Condition
MIL-STD-883H Method 3015.8
JEDEC-EIA/JESD22-A115
JEDEC-EIA/JESD22-C101E
Minimum Level
8
500
2
Unit
kV
V
kV
Order Information
Model Name
TP1561A
TP1561NA
TP1562A
TP1564A
Order Number
TP1561A-TR
TP1561A-CR
TP1561NA-TR
TP1562A-SR
TP1562A-VR
TP1562A-TR
TP1564A-SR
TP1564A-TR
Package
5-Pin SOT23
5-Pin SC70
6-Pin SOT23
8-Pin SOIC
8-Pin MSOP
8-Pin TSSOP
14-Pin SOIC
14-Pin TSSOP
Transport Media, Quantity
Tape and Reel, 3000
Tape and Reel, 3000
Tape and Reel, 3000
Tape and Reel, 4000
Tape and Reel, 3000
Tape and Reel, 3000
Tape and Reel, 2500
Tape and Reel, 3000
Marking
Information
561
561
56N
1562A
1562A
1562A
1564A
1564A
2 Rev. B.03
www.3peakic.com.cn


Part Number TP1562A
Description Op Amps
Maker 3Peak
Total Page 19 Pages
PDF Download

TP1562A Datasheet PDF

View PDF for Mobile








Similar Datasheet

1 TP1562 Op Amps
3Peak
2 TP1562A Op Amps
3Peak
3 TP1562AL1 Op Amps
3Peak





Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

Site map

Webmaste! click here

Contact us

Buy Components

Privacy Policy