http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




TEMIC Semiconductors
TEMIC Semiconductors


U208

Open Loop Phase Control Circuit



No Preview Available !

U208 pdf
Open Loop Phase Control Circuit
U208B
Description
The integrated circuit, U208B, is designed as a phase con-
trol circuit in bipolar technology with internal
supply-voltage monitoring. As the voltage is built up, un-
controlled output pulses are avoided by internal
monitoring. Furthermore, it has internal-current and volt-
age synchronisation. It is recommended as a low cost
open-loop control.
Features
D Automatic retriggering
D Triggering pulse typ. 125 mA
D Voltage and current synchronisation
D Internal supply voltage monitoring
D Current requirement 2.5 mA
Package: DIP8
Block Diagram
R3
220 kW/
0.5 W
7
R4
470 kW/
0.5 W
8
Voltage Current
detector detector
Automatic
retriggering
BYT77
18 kW/
2W
D1
M
R1
L
95 11224
Output
pulse
3
R7
180 W
TIC
236N
VM =
230 V ~
R2
180 kW
R6
18 kW
100 kW
R5
120 kW
4
6
Phase
control unit
ö = f (V6)
Supply
voltage
limitation
Voltage
monitoring
10 nF
5
C2
2
–VS
1
C1
GND
22 mF/
25 V
N
Figure 1. Block diagram for simple phase control system
TELEFUNKEN Semiconductors
Rev. A1, 28-May-96
1 (7)



No Preview Available !

U208 pdf
U208B
Description
Mains Supply
The U208B is fitted with voltage limiting and can there-
ăfore be supplied directly from the mains. The supply
voltage between Pin 1 (+ pol/ ) and Pin 2 builds up
across D1 and R1 and is smoothed by C1. The value of the
series resistance can be approximated using figure 1:
+R1
VM–VS
2 IS
Further information regarding the design of the mains
supply can be found in the data sheets in the appendix.
Operation using an externally stabilized DC voltage is not
recommended.
If the supply cannot be taken directly from the mains
because the power dissipation in R1 would be too large,
then the circuit shown in the following figure 2 should be
employed.
~
24 V~
12345
R1 C1
95 10362
Figure 2. Supply voltage for high current requirements
Phase Control
The function of the phase control is largely identical to
that of the well known component TEA1007. The phase
angle of the trigger pulse is derived by comparing the
ramp voltage, which is mains synchronized by the voltage
detector, with the nominal value predetermined at the
control input Pin 6. The slope of the ramp is determined
by C2 and its charging current. The charging current can
be varied using R2 on Pin 4. The maximum phase angle
amax can also be adjusted using R2.
When the potential on Pin 5 reaches the given value of
Pin 6, then a trigger pulse is generated whose width tp is
determined by the value of C2 (the value of C2 and hence
the pulse width can be evaluated by assuming 8 ms/nF).
The current sensor on Pin 8 ensures that, for operation
with inductive loads, no pulse will be generated in a new
half cycle as long as the current from the previous half
cycle is still flowing in the opposite direction to the sup-
ply voltage at that instant. This makes sure that ”Gaps” in
the load current are prevented. The control signal on Pin
6 can be in the range 0 V to –7 V (reference point Pin 1).
If Vpin6 = –7 V then the phase angle is at maximum = amax
i.e., the current flow angle is a minimum. The minimum
phase angle amin is when Vpin6 = Vpin1.
Voltage Monitoring
As the voltage is built up, uncontrolled output pulses are
avoided by internal voltage surveillance. At the same
time, all of the latches in the circuit are reset. Used with
a switching hysteresis of 300 mV, this system guarantees
defined start–up behavior each time the supply voltage is
switched on ,or after short interruptions of the mains
supply.
Pulse Output Stage
The pulse output stage is short circuit protected and can
typically deliver currents of 125 mA. For the design of
smaller triggering currents, the function IGT = f (RGT) has
been given in the data sheets in the appendix. In contrast
to the TEA1007, the pulse output stage of the U 208 B has
no gate bypass resistor.
Automatic Retriggering
The automatic retriggering prevents half cycles without
current flow, even if the triacs is turned off earlier e.g. due
to a collector which is not exactly centered (brush lifter)
or in the event of unsuccessful triggering. If it is neces-
sary, another triggering pulse is generated after a time
lapse of tpp = 4.5 tp and this is repeated until either the
triac fires or the half cycle finishes.
2 (7) TELEFUNKEN Semiconductors
Rev. A1, 28-May-96



Part Number U208
Description Open Loop Phase Control Circuit
Maker TEMIC Semiconductors - TEMIC Semiconductors
Total Page 7 Pages
PDF Download
U208 pdf
Download PDF File
U208 pdf
View for Mobile




Featured Datasheets

Part Number Description Manufacturers PDF
U2000 USB Power Sensors U2000
Agilent
PDF
U2008B Low Cost Current Feedback Phase Control Circuit U2008B
TEMIC Semiconductors
PDF
U2008B Low-Cost Phase-Control IC with Soft Start U2008B
ATMEL Corporation
PDF
U2008B-M Low-Cost Phase-Control IC with Soft Start U2008B-M
ATMEL Corporation
PDF
U2008B-MFP Low-Cost Phase-Control IC with Soft Start U2008B-MFP
ATMEL Corporation
PDF
U2008B-MFPG3 Low-Cost Phase-Control IC with Soft Start U2008B-MFPG3
ATMEL Corporation
PDF


Part Number Start With

0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z

site map

webmaste! click here

contact us

Buy Components