900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf

Clare  Inc.
Clare Inc.


DTMF Transceiver

No Preview Available !

M-8888-01SM pdf
· Advanced CMOS technology for low power con-
sumption and increased noise immunity
· Complete DTMF transmitter/receiver in a single
Standard 8051, 8086/8 microprocessor port
· Central office quality and performance
· Adjustable guard time
· Automatic tone burst mode
· Call progress mode
· Single +5 Volt power supply
· 20-pin DIP and SOIC packages
· 2 MHz microprocessor port operation
·· Inexpensive 3.58 MHz crystal
Paging systems
· Repeater systems/mobile radio
· Interconnect dialers
· PBX systems
· Computer systems
· Fax machines
· Pay telephone
·· Credit card verification
DTMF Transceiver
The M-8888 is a complete DTMF Transmitter
Receiver that features adjustable guard time, auto-
matic tone burst mode, call progress mode, and a fully
compatible 8051, 8086/8 microprocessor interface.
The receiver portion is based on the industry standard
M-8870 DTMF Receiver, while the transmitter uses a
switched-capacitor digital-to-analog converter for low-
distortion, highly accurate DTMF signaling. Tone
bursts can be transmitted with precise timing by mak-
ing use of the automatic tone burst mode. To analyze
call progress tones, a call progress filter can be select-
ed by an external microprocessor.
Ordering Information
Part #
20-pin plastic DIP
M-8888-01SM 20-pin plastic SOIC
20-pin plastic SOIC,Tape and Reel
Pin Connections
Block Diagram

No Preview Available !

M-8888-01SM pdf
Single-Ended Input Configuration
Differential Input Configuration
Functional Description
M-8888 functions consist of a high-performance
DTMF receiver with an internal gain setting amplifier
and a DTMF generator that contains a tone burst
counter for generating precise tone bursts and paus-
es. The call progress mode, when selected, allows the
detection of call progress tones. A standard 8051,
8086/8 series microprocessor interface allows access
to an internal status register, two control registers, and
two data registers.
ing the amplifier inputs at VDD/2. Provisions are made
for the connection of a feedback resistor to the op-amp
output (GS) for gain adjustment. In a single-ended
configuration, the input pins should be connected as
shown in the Single-Ended Input Configuration above.
Differential Input Configuration above shows the nec-
essary connections for a differential input configura-
Input Configuration
The input arrangement consists of a differential input
operational amplifier and bias sources (VREF) for bias-
Receiver Section
The low and high group tones are separated by apply-
ing the DTMF signal to the inputs of two sixth-order
Pin Functions
Noninverting op-amp input.
Inverting op-amp input.
Gain select. Gives access to output of front end differential amplifier for connection of feedback resistor.
Reference voltage output. Nominally VDD/2 is used to bias inputs at mid-rail.
Negative power supply input.
DTMF clock/oscillator input.
Clock output. A 3.5795 MHz crystal connected between OSC1 and OSC2 completes the internal oscillator circuit.
Dual tone multifrequency (DTMF) output.
Write input. A low on this pin when CS is low enables data transfer from the microprocessor. TTL compatible.
Chip select. TTL input (CS = 0 to select the chip).
Register select input. See Internal Register Functions on page 7. TTL compatible.
Read input. A low on this pin when CS is low enables data transfer to the microprocessor. TTL compatible..
Interrupt request to microprocessor (open-drain output). Also, when call progress (CP) mode has been selected and
interrupt enabled, the IRQ/CP pin will output a rectangular wave signal representative of the input signal applied at the
input op-amp. The input signal must be within the bandwidth limits of the call progress filter. See Timing Diagrams on
page 11.
Microprocessor data bus. TTL compatible.
Early steering output. Presents a logic high once the digital algorithm has detected a valid tone pair (signal condition).
Any momentary loss of signal condition will cause ESt to return to a logic low.
Steering input/guard time output (bidirectional). A voltage greater than VTSt detected at St causes the device to register
the detected tone pair and update the output latch. A voltage less than VTSt frees the device to accept a new tone pair. The
GT output acts to reset the external steering time-constant; its state is a function of ESt and the voltage on St.
Positive power supply input.
Rev. 1

Part Number M-8888-01SM
Description DTMF Transceiver
Maker Clare  Inc. - Clare Inc.
Total Page 14 Pages
PDF Download
M-8888-01SM pdf
Download PDF File
M-8888-01SM pdf
View for Mobile

Featured Datasheets

Part Number Description Manufacturers PDF
M-8888-01 DTMF Transceiver M-8888-01
Clare Inc.
M-8888-01P DTMF Transceiver M-8888-01P
Clare Inc.
M-8888-01SM DTMF Transceiver M-8888-01SM
Clare Inc.
M-8888-01T DTMF Transceiver M-8888-01T
Clare Inc.

Part Number Start With

0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z

site map

webmaste! click here

contact us

Buy Components