900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf

Clare  Inc.
Clare Inc.


M-8880 DTMF Transceiver

No Preview Available !

M-8880 pdf
M-8880 DTMF Transceiver
· Advanced CMOS technology for low power consump-
tion and increased noise immunity
· Complete DTMF transmitter/receiver in a single chip
· Standard 6500/6800 series microprocessor port
· Central office quality and performance
· Adjustable guard time
· Automatic tone burst mode
· Call progress mode
· Single +5 Volt power supply
· 20-pin DIP and SOIC packages
· 2 MHz microprocessor port operation
· Inexpensive 3.58 MHz crystal
· No continuous f2 clock required, only strobe
· Applications include: paging systems, repeater sys-
tems/mobile radio, interconnect dialers, PBX systems,
computer systems, fax machines, pay telephones,
credit card verification
The M-8880 is a complete DTMF Transmitter/Receiver that fea-
tures adjustable guard time, automatic tone burst mode, call
progress mode, and a fully compatible 6500/6800 microproces-
sor interface. The receiver portion is based on the industry stan-
dard M-8870 DTMF Receiver, while the transmitter uses a
switched-capacitor digital-to-analog converter for
low-distortion, highly accurate DTMF signaling. Tone bursts can
be transmitted with precise timing by making use of the auto-
matic tone burst mode. To analyze call progress tones, a call
progress filter can be selected by an external microprocessor.
Figure 1 Pin Diagram
Functional Description
M-8880 functions consist of a high-performance DTMF receiver
with an internal gain setting amplifier and a DTMF generator that
contains a tone burst counter for generating precise tone bursts
and pauses. The call progress mode, when selected, allows the
detection of call progress tones. A standard 6500/6800 series
microprocessor interface allows access to an internal status
register, two control registers, and two data registers.
Input Configuration
The input arrangement consists of a differential input opera-
tional amplifier and bias sources (VREF) for biasing the amplifier
inputs at VDD/2. Provisions are made for the connection of a
feedback resistor to the op-amp output (GS) for gain adjust-
40-406-00012, Rev. G
Figure 2 Block Diagram
Page 1

No Preview Available !

M-8880 pdf
Figure 3 Single-Ended Input Configuration
Figure 4 Differential Input Configuration
ment. In a single-ended configuration, the input pins should be
connected as shown in Figure 3. Figure 4 shows the necessary
connections for a differential input configuration.
Receiver Section
The low and high group tones are separated by applying the
DTMF signal to the inputs of two sixth-order switched capacitor
bandpass filters with bandwidths that correspond to the low and
high group frequencies listed in Table 2. The low group filter in-
corporates notches at 350 and 440 Hz, providing excellent dial
tone rejection. Each filter output is followed by a single-order
switched capacitor filter that smooths the signals prior to limiting.
Limiting is performed by high-gain comparators with hysteresis
to prevent detection of unwanted low-level signals. The com-
parator outputs provide full-rail logic swings at the incoming
DTMF signal frequencies.
A decoder employs digital counting techniques to determine the
frequencies of the incoming tones, and to verify that they corre-
spond to standard DTMF frequencies. A complex averaging al-
gorithm protects against tone simulation by extraneous signals
(such as voice), while tolerating small deviations in frequency.
The algorithm provides an optimum combination of immunity to
talkoff with tolerance to interfering frequencies (third tones) and
noise. When the detector recognizes the presence of two valid
tones (referred to as “signal condition”), the early steering (ESt)
output goes to an active state. Any subsequent loss of signal
condition will cause ESt to assume an inactive state.
Steering Circuit: Before a decoded tone pair is registered, the
receiver checks for a valid signal duration (referred to as “char-
acter recognition condition”). This check is performed by an ex-
ternal RC time constant driven by ESt. A logic high on ESt
Table 1 Pin Functions
D0 - D3
Noninverting op-amp input.
Inverting op-amp input.
Gain select. Gives access to output of front end differential amplifier for connection of feedback resistor.
Reference voltage output. Nominally VDD/2 is used to bias inputs at mid-rail.
Negative power supply input.
DTMF clock/oscillator input.
Clock output. A 3.5795 MHz crystal connected between OSC1 and OSC2 completes the internal oscillator circuit.
Dual tone multifrequency (DTMF) output.
Read/write input. Controls the direction of data transfer to and from the microprocessor and the receiver/transmitter. TTL
Chip select. TTL input (CS = 0 to select the chip).
Register select input. See Table 6. TTL compatible.
System clock input. May be continuous or strobed only during read or write. TTL compatible.
Interrupt request to microprocessor (open-drain output). Also, when call progress (CP) mode has been selected and inter-
rupt enabled, the IRQ/CP pin will output a rectangular wave signal representative of the input signal applied at the input
op-amp. The input signal must be within the bandwidth limits of the call progress filter. See Figure 11
Microprocessor data bus. TTL compatible.
Early steering output. Presents a logic high once the digital algorithm has detected a valid tone pair (signal condition). Any
momentary loss of signal condition will cause ESt to return to a logic low.
Steering input/guard time output (bidirectional). A voltage greater than VTSt detected at St causes the device to register the
detected tone pair and update the output latch. A voltage less than VTSt frees the device to accept a new tone pair. The
GT output acts to reset the external steering time-constant; its state is a funciton of ESt and the voltage on St.
Positive power supply input.
40-406-00012, Rev. G
Page 2

Part Number M-8880
Description M-8880 DTMF Transceiver
Maker Clare  Inc. - Clare Inc.
Total Page 13 Pages
PDF Download
M-8880 pdf
Download PDF File
M-8880 pdf
View for Mobile

Featured Datasheets

Part Number Description Manufacturers PDF
M-8870 DTMF Receiver M-8870
Clare Inc.
M-8870 DTMF Receiver M-8870
M-8870-01 DTMF Receiver M-8870-01
Clare Inc.
M-8870-01SM DTMF Receiver M-8870-01SM
Clare Inc.
M-8870-01SMTR DTMF Receiver M-8870-01SMTR
Clare Inc.
M-8870-02 DTMF Receiver M-8870-02
Clare Inc.

Part Number Start With

0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z

site map

webmaste! click here

contact us

Buy Components