http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




ETC
ETC


G219R-D3

Ultra320 Multi-mode LVD/SE SCSI Terminator


No Preview Available !

G219R-D3 pdf
Global Mixed-mode Technology Inc.
G219
Ultra320 Multi-mode LVD/SE SCSI Terminator
Features
„Auto-selectable multi-mode Single-Ended
or LVD Termination
„Meets SCSI-1, SCSI-2, SCSI-3 SPI Ultra
(Fast-20), Ultra 2(SPI-2 LVD), Ultra160 (SPI-3
LVD), and Ultra320 (SPI-4 LVD) standards
„Supports active negation
„3pF channel capacitance
„2.9V to 5.5V operation
„Thermal protection
„Hot-Swap compatible
„5% tolerance on SE and LVD termination
resistance
„28 pin TSSOP package
„28 Pin TSSOP: Pin Compatible with DS2119
Applications
„Server and workstation
„High-end PC
„Industrial PC
„Disk Array (RAID)
„SCSI cable
General Description
The G219 Multi-mode LVD/SE SCSI terminator pro-
vides a smooth transition into the next generation of
the SCSI Parallel Interface (SPI-4). It automatically
senses the bus, via DIFFSENS, and switches the ter-
mination to either single-ended (SE) or low voltage
differential (LVD) SCSI, dependent on which type of
devices are connected to the bus. If the G219 detects
a HVD SCSI device, it switches to a high impedance
state. For a 16-bit Wide SCSI bus to be operational,
three G219 terminators are needed.
The Multi-mode terminator contains all functions re-
quired to terminate and auto detect and switch modes
for SCSI Parallel Interface (SPI) bus architectures. For
the SE termination, one regulator and nine precision
110ohm resistors are used. For the LVD termination,
the G219 integrates 18 regulated supplies with nine
precision resistor strings.
Pin Configuration
VREF 1
R1+ 2
R1- 3
R2+ 4
R2- 5
NC/ HS GND
R3+
R3-
R4+
6
7
8
9
R4- 10
R5+ 11
R5- 12
DISCNCT 13
GND 14
G219
28 TPWR
27 TPWR
26 R9-
25 R9+
24 R8-
23 R8+
22 NC/ HS GND
21 R7-
20 R7+
19 R6-
18 R6+
17 DIFFB
16 DIFFSENSE
15 M/S
28Pin TSSOP
Ver 1.2
Feb 08, 2002
TEL: 886-3-5788833
http://www.gmt.com.tw
1



No Preview Available !

G219R-D3 pdf
Global Mixed-mode Technology Inc.
Ordering Information
G219
PART NUMBER
G219T-D3
G219R-D3
TEMP. RANGE
0ºC-70ºC
0ºC-70ºC
PIN-PACKAGE
TSSOP-28 pin / Tube
TSSOP-28 pin / Tape & Reel
Note:
DIFFSENSRefers to the SCSI bus signal.
DIFFSENSERefers to the G219 pin name and internal circuitry relating to differential sensing.
DIFFBRefers to the G219 pin name and internal circuitry relating to monitoring the DIFFSENS line.
Functional Description
The G219 is used in multi-mode active termination
applications, where single ended (SE) and low voltage
differential (LVD) devices might coexist. The LVD ter-
mination section consists of 18 source/sink amplifiers
(VTOP, VBOT), biasing circuitry and nine precision
resistor strings (RTOP, RMID, RBOT). The SE termi-
nation section consists of a 2.85V source/sink regula-
tor with 9 precision 110ohm resistor. The DIFFSENSE
section consists of a 1.3V, 5mA driver and a sensing
circuit (Figure 1)
DIFFSENS is used to identify which types of SCSI
devices are present on the bus. If the voltage on
DIFFSENS is between 0-0.5V the bus is single-ended;
if it is between 0.7-1.9V the bus is LVD; and if it is
greater than 2.4V, the bus is HVD.
The G219 DIFFB pin monitors the DIFFSENS line to
determine the proper operating mode of the device.
HVD Isolation Mode The G219 identifies that there is
an HVD (high voltage differential) device on the SCSI
bus and isolates the termination pins from the bus.
When DISCNCT is pulled high, the termination pins
are isolated from the SCSI bus, and VREF is
grounded. During thermal shutdown, the termination
pins are isolated from the SCSI bus and VREF is
grounded. The DIFFSENSE driver is shut down during
either of these two events.
To ensure proper operation, the TPWR pin should be
connected to the SCSI bus TERMPWR line. As with all
analog circuitry, the TERMPWR lines should be by-
passed locally. A 2.2µF capacitor and a 0.01µF high
frequency capacitor is recommended between TPWR
and ground and placed as close as possible to the
G219. The G219 should be placed as close as possi-
ble to the SCSI connector to minimize signal and
power trace length, thereby resulting in less input ca-
pacitance and reflections which can degrade the bus
signals.
The DIFFSENSE pin can drive the SCSI DIFFSENS
line (when M/S is pulled high) to determine the SCSI
bus operating mode. The G219 switches to the termi-
nation mode that is appropriate for the bus based on
the value of the DIFFSENS voltage. These modes are:
LVD mode LVD termination is provided by a precision
resistor string with two amplifiers. This configuration
yields a 105differential and 150common mode
impedance. A fail safe bias of 112mV is maintained
when no drivers are connected to the SCSI bus.
SE mode When the external driver for a given signal
line turns off, the active terminator will pull that signal
line to 2.85 volts (quiescent state). When used with an
active negation driver, the power amp can sink 22mA
per line while keeping the voltage reference in regula-
tion. The terminating resistors maintain their 110
value.
To maintain the specified regulation, a 4.7µF capacitor
is required between the VREF pin and ground of each
G219. A high frequency cap (0.1µF ceramic recom-
mended) can also be placed on the VREF pin in ap-
plications that use fast rise/fall time drivers. A typical
SCSI bus configuration is shown in Figure2.
An internal pull down resistor assures that the G219
will be terminating the bus if the DISCNCT pin is left
floating.
DIFFSENS noise filtering
The G219 incorporates a internal digital filter to re-
move the noise signal on the DIFFSENS control line,
thereby eliminating erroneous switching between
modes. The external filter may be used in addition to
the internal digital filter.
Ver 1.2
Feb 08, 2002
TEL: 886-3-5788833
http://www.gmt.com.tw
2



Part Number G219R-D3
Description Ultra320 Multi-mode LVD/SE SCSI Terminator
Maker ETC - ETC
Total Page 9 Pages
PDF Download
G219R-D3 pdf
Download PDF File
G219R-D3 pdf
View for Mobile




Featured Datasheets

Part Number Description Manufacturers PDF
G219R-D3 Ultra320 Multi-mode LVD/SE SCSI Terminator G219R-D3
ETC
PDF


Part Number Start With

0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z

site map

webmaste! click here

contact us

Buy Components