Schottky Barrier Diode

This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. DATE S P E C I F I C AT I O N ： Schottky Barrier Diode DWG.NO. CHECKED SEP.-05-‘03 DRAWN SEP.-05-‘03 SEP.-05-‘03 NAME www.DataSheet4U.com Device Name Spec. No. Type Name Model Name APPROVED ： SILICON DIODE ： MS5D1917 ： YA846C04B Fuji Electric Co.,Ltd. MS5D1917 Fuji Electric Co.,Ltd. Matsumoto Factory 1/12 H04-004-07 This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. SEP.-05 -2003 Date Classification Enactment Ind. ― DWG.NO. Fuji Electric Co.,Ltd. Content ―――――― Issued date ――― Applied date Drawn Checked Approved Revised Records MS5D1917 2/12 H04-004-06 1. SCOPE This specification provides the ratings and the test requirement for FUJI SILICON DIODE YA846C04B 2. OUT VIEW, MARKING, MOLDING RESIN, CHARACTERISTICS (1)Out view is shown (2)Marking is shown (3)Molding resin Epoxy resin UL : V-0 (4)Characteristics is shown MS5D1917 10/12～12/12 3. RATINGS 3.1 MAXIMUM RATINGS (at Tc=25℃ unless otherwise specified.) ITEM SYMBOL CONDITIONS RATINGS Repetitive peak surge reverse voltage VRSM tw=500ns,duty=1/40 45 Repetitive peak reverse voltage VRRM 45 Square wave duty =1/2 Average output current Io 30* Tc= 98 ℃ Non-repetitive surge current ** IFSM Sine wave, 10ms 1shot 200 Operating junction temperature Tj 150 Storage temperature Tstg -40～+150 * Out put current of center tap full wave connection. ** MS5D1917 MS5D1917 9/12 9/12 It is marked to type name or abbreviated type name, polarity and Lot No. UNITS V V A A ℃ ℃ This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. Rating per element UNITS V mA ℃/W 3.2 ELECTRICAL CHARACTERISTICS (at Tc=25℃ unless otherwise specified.) ITEM SYMBOL CONDITIONS MAXIMUM *** Forward voltage VF IF= 12.5A 0.55 Reverse current *** IR VR=VRRM 1.0 Thermal resistance Rth(j-c) Junction to case 2.0 *** Rating per element 3.3 MECHANICAL CHARACTERISTICS Mounting torque Approximate mass Recommended torque 0.3～0.5 2.0 N・m g Fuji Electric Co.,Ltd. DWG.NO. MS5D1917 3/12 H04-004-03 4. TEST AND INSPECTION 4.1 STANDARD TEST CONDITION Standard test condition is Ta=25℃、RH=65%. If judgment is no doubt, the test condition is possible to test in normal condition Ta=5～35℃、RH=48～85% 4.2 STRUCTURE INSPECTION It inspect with eye and measure,Item2 shall be satisfied. 4.3 FORWARD AND REVERSE CHARACTERISTICS It inspect on the standard condition,Item3.2 shall be satisfied. 4.4 TEST Test No. Test Items Testing methods and Conditions Pull force : 10N Force maintaining duration :10±1s Load force : 5N Number of times : 2times(90deg./time) Screwing torque value:(M3) : 40±10N・cm Reference Standard EIAJ ED4701 A-111A method 1 A-111A method 3 A-112 method 2 Sampling number Acceptance number This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. 1 Terminal Strength (Tensile) 2 Terminal Strength (Bending) 3 Mounting Strength 4 Vibration Mechanical test 5 5 5 5 Shock 6 Solder ability 7 Resistance to Soldering Heat Frequency : 100Hz to 2kHz Acceleration : 100m/s2 A-121 Sweeping time : 4min./1 cycle 4times for each X, Y&Z directions. Peak amplitude : 15km/s2 A-122 Duration time : 0.5ms test code D 3times for each X, Y&Z directions. Solder temp. : 235±5℃ Immersion time : 5±0.5s A-131A Each terminal shall be immersed in the test code A solder bath within 1to3.0mm from the body. Solder temp. : 260±5°C A-132 Immersion time : 10±1s Number of times : 1times 5 (0 : 1) 5 5 5 Fuji Electric Co.,Ltd. DWG.NO. MS5D1917 4/12 H04-004-03 Test No. Test Items Testing methods and Conditions Temperature :Ｔstg max Test duration : 1000h Temperature :Ｔstg min Test duration : 1000h Temperature : 85±2°C Relative humidity : 85±5% Test duration : 1000h Temperature : 85±2°C Relative humidity : 85±5% Bias Voltage : VRRM× 0.8 Test duration : 1000h Temperature : 130±2°C Relative humidity : 85±5% Vapor pressure : 230kPa Test duration : 48h High temp. side : Tstg max Room temp. : 5～35℃ Low temp. side : Tstg min Duration time : HT 30min,RT 5min LT 30min Number of cycles : 100 cycles Fluid : pure water(running water) High temp. side : 100+0/-5°C Low temp. side : 0+5/-0°C Duration time : HT 5min,LT 5min Number of cycles : 100 cycles Ta=25±5°C Rated load Test duration : 1000h Tj=Tjmax ～50℃ 3min ON, 3min OFF Test duration : 10000cy Temperature : Ta=100 °C Bias Voltage : VR=VRRM duty=1/2 Test duration : 1000h Reference Standard EIAJ ED4701 B-111A B-112A B-121A test code C B-122A test code C Samplin g number 22 22 22 Acceptance number 1 High Temp. Storage 2 Low Temp. Storage 3 Temperature Humidity Storage 4 Temperature Humidity Bias 5 Unsaturated Pressurized Vapor Endurance test 6 Temperature Cycle 22 B-123A test code B 22 This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. B-131A 22 (0 : 1) 7 Thermal Shock B-141A test code A 22 8 Steady state Operating life 9 Intermittent Operating life 10 High Temp. Reverse Bias D-402 22 D-403 22 D-404 22 Failure Criteria IR ≦USL x 2 VF≦USL x 1.1 USL : Upper specification Limit Fuji Electric Co.,Ltd. DWG.NO. MS5D1917 5/12 H04-004-03 5.Cautions ・Although Fuji Electric is continually improving product quality and reliability, a small percentage of semiconductor products may become faulty. When using Fuji Electric semiconductor products in your equipment, you are requested to take adequate safety measures to prevent the equipment from causing physical injury, fire, or other problem in case any of the products fail. It is recommended to make your design fail-safe, flame retardant, and free of malfunction. ・The products described in this specification are intended for use in the following electronic and electrical equipment which has normal reliability requirements. ・Computers ・OA equipment ・Measurement equipment ・Electrical home appliances ・Communications equipment (Terminal devices) ・Machine tools ・Personal equipment ・AV equipment ・Industrial robots etc. ・The products described in this Specification are not designed or manufactured to be used in equipment or systems used under life-threatening situations. If you are considering using these products in the equipment listed below, first check the system construction and required reliability, and take adequate safety measures such as a backup system to prevent the equipment from malfunctioning. ・Transportation equipment (automobiles, trains, ships, etc.) ・Backbone network equipment This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. ・Traffic-signal control equipment ・Submarine repeater equipment ・Medical equipment ・Gas alarms, leakage gas auto breakers ・Burglar alarms, fire alarms, emergency equipment ・Nuclear control equipment etc. ・Do not use the products in this Specification for equipment requiring strict reliability such as (but not limited to): ・Aerospace equipment ・Aeronautical equipment 6.Warnings ・ The Diodes should be used in products within their absolute maximum rating (voltage, current, temperature, etc. ). The diodes may be destroyed if used beyond the rating. ・The equipment containing Diodes should have adequate fuses or circuit breakers to prevent the equipment from causing secondary destruction (ex. fire, explosion etc…). ・Use the Diodes within their reliability and lifetime under certain environments or conditions. The Diodes may fail before the target lifetime of your products if used under certain reliability conditions. ・You must design the Diodes to be operated within the specified maximum ratings (voltage, current, temperature, etc. ) to prevent possible failure or destruction of devices. ・Consider the possible temperature rise not only for the junction and case, but also for the outer leads. ・Do not directly touch the leads or package of the Diodes while power is supplied or during operation, to avoid electric shock and burns. ・The Diodes are made of incombustible material. However, if a diode fails, it may emit smoke of flame. Also, operating the Diodes near any flammable place or material may cause the diodes to emit smoke or flame in case the Diodes become even hotter during operation. Design the arrangement to prevent the spread of fire. ・The Diodes should not used in an environment in the presence of acid, organic matter, or corrosive gas. (hydrogen sulfide, sulfurous acid