BIPOLAR ANALOG INTEGRATED CIRCUIT

www.DataSheet4U.com BIPOLAR ANALOG INTEGRATED CIRCUIT UPC3224TB 5 V, SILICON MMIC WIDEBAND AMPLIFIER DESCRIPTION The µPC3224TB is a silicon monolithic IC designed as IF amplifier for DBS tuners. This IC is manufactured using our 30 GHz fmax UHS0 (Ultra High Speed Process) silicon bipolar process. FEATURES • Wideband response : fu = 3.2 GHz TYP. @ 3 dB bandwidth • Low current • Power gain • Supply voltage • Port impedance : ICC = 9.0 mA TYP. : GP = 21.5 dB TYP. @ f = 1.0 GHz : GP = 21.5 dB TYP. @ f = 2.2 GHz : VCC = 4.5 to 5.5 V : input/output 50 Ω APPLICATION • IF amplifiers in DBS converters etc. ORDERING INFORMATION (Solder Contains Lead) Part Number Package 6-pin super minimold Marking C3K Supplying Form • Embossed tape 8 mm wide • 1, 2, 3 pins face the perforation side of tape • Qty 3 kpcs/reel µPC3224TB-E3 ORDERING INFORMATION (Pb-Free) Part Number Package 6-pin super minimold Marking C3K Supplying Form • Embossed tape 8 mm wide • 1, 2, 3 pins face the perforation side of tape • Qty 3 kpcs/reel µPC3224TB-E3-A Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: µPC3224TB Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. Document No. PU10490EJ01V0DS (1st edition) Date Published May 2004 CP(K) © NEC Compound Semiconductor Devices 2004 UPC3224TB PIN CONNECTIONS Pin No. Pin Name INPUT GND GND OUTPUT GND VCC (Top View) (Bottom View) 1 C3K 3 2 1 4 5 6 4 5 6 3 2 1 2 3 4 5 6 PRODUCT LINE-UP OF 5 V-BIAS SILICON MMIC MEDIUM WIDEBAND AMPLIFIER (TA = +25°C, f = 1 GHz, VCC = Vout = 5.0 V, ZS = ZL = 50 Ω) fu (GHz) 2.9 2.6 Note Part No. PO (sat) (dBm) +1.0 +3.0 +3.5 +4.0 GP (dB) 13 20 20.5 21.5 NF (dB) 5.0 4.5 2.3 4.3 ICC (mA) 12 12 14 9.0 Package 6-pin super minimold Marking C1G C1H C3H C3K µPC2711TB µPC2712TB µPC3215TB µPC3224TB 2.9 3.2 Note µPC3215TB is f = 1.5 GHz Remark Typical performance. Please refer to ELECTRICAL CHARACTERISTICS in detail. 2 Data Sheet PU10490EJ01V0DS UPC3224TB PIN EXPLANATIONS PIN No. 1 Pin Name INPUT Applied Voltage (V) – Pin Voltage Note (V) 0.91 Signal input pin. A internal matching circuit, configured with resistors, enables 50 Ω connection over a wide band. A multi-feedback circuits is designed to cancel the deviations of hFE and resistance. This pin must be coupled to signal source with capacitor for DC cut. 4 OUTPUT – 4.42 Signal output pin. A internal matching circuit, configured with resistors, enables 50 Ω connection over a wide band. This pin must be coupled to next stage with capacitor for DC cut. 6 VCC 4.5 to 5.5 – Power suplly pin. This pin should be externally equipped with bypass capacitor to minimize its impedance. 2 3 5 GND 0 – Ground pin. This pin should be connected to system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. All the ground pins must be connected together with wide ground pattern to decrease impedance difference. Function and Applications Note Pin Voltage is measured at VCC = 5.0 V Data Sheet PU10490EJ01V0DS 3 UPC3224TB ABSOLUTE MAXIMUM RATINGS Parameter Supply Voltage Total Circuit Current Power Dissipation Operating Ambient Temperature Storage Temperature Input Power Symbol VCC ICC PD TA Tstg Pin TA = +25°C TA = +25°C TA = +25°C TA = +85°C Note Conditions Ratings 6.0 25 270 −40 to +85 −55 to +150 +10 Unit V mA mW °C °C dBm Note Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB RECOMMENDED OPERATING RANGE Parameter Supply Voltage Operating Ambient Temperature Symbol VCC TA Conditions MIN. 4.5 −40 TYP. 5.0 +25 MAX. 5.5 +85 Unit V °C ELECTRICAL CHARACTERISTICS (TA = +25°C, VCC = 5.0 V, ZS = ZL = 50 Ω) Parameter Circuit Current Power Gain Symbol ICC GP Test Conditions No input signal f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Saturated Output Power PO (sat) f = 1.0 GHz, Pin = −5 dBm f = 2.2 GHz, Pin = −5 dBm Gain 1 dB Compression Output Power Noise Figure NF PO (1 dB) f = 1.0 GHz f = 2.2 GHz f = 1.0 GHz f = 2.2 GHz Upper Limit Operating Frequency Isolation fu ISL 3 dB down below flat gain at f = 0.1 GHz f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Input Return Loss RLin f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Output Return Loss RLout f = 1.0 GHz, Pin = −30 dBm f = 2.2 GHz, Pin = −30 dBm Gain Flatness MIN. 7.0 19.0 18.5 +1.5 −1.5 −6.5 −8.5 − − 2.8 35.0 37.0 9.0 10.0 11.0 8.0 − TYP. 9.0 21.5 21.5 +4.0 +1.5 −3.5 −5.5 4.3 4.3 3.2 40.0 42.0 12.0 14.0 17.0 12.0 ±0.8 MAX. 12.0 24.0 24.5 − − − − 5.8 5.8 − − − − − − − − dB dB dB GHz dB dB dBm dBm Unit mA dB ∆GP f = 0.1 to 2.2 GHz 4 Data Sheet PU10490EJ01V0DS UPC3224TB OTHER CHARACTERISTICS, FOR REFERENCE PURPOSES ONLY (TA = +25°C, VCC = 5.0 V, ZS = ZL = 50 Ω) Parameter Output Intercept Point Symbol OIP3 Test Conditions f = 1.0 GHz f = 2.2 GHz Reference Value +7.0 +5.5 Unit dBm Data Sheet PU10490EJ01V0DS 5 UPC3224TB TEST CIRCUIT VCC C4 1 000 pF 1 000 pF C3 6 50 Ω IN 100 pF C1 1 4 C2 100 pF 50 Ω OUT 2, 3, 5 The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. COMPONENTS OF TEST CIRCUIT FOR MEASURING ELECTRICAL CHARACTERISTICS Type C1, C2 C3 C4 Chip Capacitor Chip Capacitor Feed-through Capacitor Value 100 pF 1 000 pF 1 000 pF CAPACITORS FOR THE VCC, INPUT AND OUTPUT PINS Capacitors of 1000 pF are recommendable as the bypass capacitor for the VCC pin and the coupling capacitors for the input and output pins. The bypass capacitor connected to the VCC pin is used to minimize ground impedance of VCC pin. So, stable bias can be supplied against VCC fluctuation. The coupling capacitors, connected to the input and output pins, are used to cut the DC and minimize RF serial impedance. Their capacitances are therefore selected as lower impedance against a 50 Ω load. The capacitors thus perform as high pass filters, suppressing low frequencies to DC. To obtain a flat gain from 100 MHz upwards, 1 000 pF capacitors are used in the test circuit. In the case of under 10 MHz operation, increase the value of coupling capacitor such as 10 000 pF. Because the coupling capacitors are determined by equation, C = 1/(2 πRfc). 6 Data Sheet PU10490EJ01V0DS UPC3224TB ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD AMP-2 IN C1 C2 OUT C3 VCC C4 COMPONENT LIST Value C1, C2 C3, C4 100 pF 1 000 pF Notes 1. 2. 3. 4. 30 × 30 × 0.4 mm double sided copper clad polyimide board. Back side: GND pattern Solder plated on pattern : Through holes Data Sheet PU10490EJ01V0DS 7 UPC3224TB TYPICAL CHARACTERISTICS (TA = +25°C , unless otherwise specified) CIRCUIT CURRENT vs. OPERATING AMBIENT TEMPERATURE 12 11 Circuit Current ICC (mA) CIRCUIT CURRENT vs. SUPPLY VOLTAGE 16 14 Circuit Current ICC (mA) No input signal No input signal VCC = 5.0 V 12 10 8 6 4 2 0 0 1 2 3 4 TA = − 40˚C 5 6 TA = +25˚C TA = +85˚C 10 9 8 7 6 − 60 − 40 − 20 0 +20 +40 +60 +80 +100 Supply Voltage VCC (V) Operating Ambient Temperature TA (°C) POWER GAIN vs. FREQUENCY 25 TA = +25˚C Input Return Loss RLin (dB) INPUT RETURN LOSS vs. FREQUENCY 10 TA = +25˚C 23 Power Gain GP (dB) VCC = 5.5 V 21 VCC = 5.0 V 19 VCC = 4.5 V 17 0 − 10 − 20 − 30 VCC = 5.0 V VCC = 5.5 V VCC = 4.5 V 1.1 2.1 3.1 4.1 5.1 15 0.1 1.1 2.1 3.1 4.1 5.1 0.1 Frequency f (GHz) Frequency f (GHz) ISOLATION vs. FREQUENCY 0 − 20 Isolation ISL (dB) OUTPUT RETURN LOSS vs. FREQUENCY 10 TA = +25˚C TA = +25˚C Output Return Loss RLout (dB) 0 − 10 VCC = 4.5 V − 20 − 30 0.1 1.1 VCC = 5.0 to 5.5 V 2.1 3.1 4.1 5.1 − 40 − 60 VCC = 4.5 to 5.5 V − 80 − 100 0.1 1.1 2.1 3.1 4.1 5.1 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. 8 Data Sheet PU10490EJ01V0DS UPC3224TB POWER GAIN vs. FREQUENCY 25 VCC = 5.0 V 23 10 VCC = 5.0 V INPUT RETURN LOSS vs. FREQUENCY Input Return Loss RLin (dB) Power Gain GP (dB) 21 TA = − 40˚C 0 TA = +25 to +85˚C − 10 − 20 − 30 19 TA = +85˚C TA = − 40˚C 17 TA = +25˚C 1.1 2.1 3.1 4.1 5.1 15 0.1 0.1 1.1 2.1 3.1 4.1 5.1 Frequency f (GHz) Frequency f (GHz) ISOLATION vs. FREQUENCY 0 − 20 VCC = 5.0 V OUTPUT RETURN LOSS vs. FREQUENCY 10 VCC = 5.0 V Output Return Loss RLout (dB) Isolation ISL (dB) 0 − 10 − 20 TA = +25˚C − 30 0.1 1.1 2.1 TA = − 40˚C 3.1 4.1 5.1 − 40 − 60 − 80 TA = +85˚C TA = − 40 to +85˚C − 100 0.1 1.1 2.1 3.1 4.1 5.1 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. Data Sheet PU10490EJ01V0DS 9 UPC3224TB OUTPUT POWER vs. INPUT POWER 10 5 0 −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) f = 1.0 GHz TA = +25˚C VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V Output Power Pout (dBm) OUTPUT POWER vs. INPUT POWER 10 5 0 TA = − 40˚C −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) f = 1.0 GHz VCC = 5.0 V TA = +25 to +85˚C Output Power Pout (dBm) 0 5 10 0 5 10 OUTPUT POWER vs. INPUT POWER 10 5 0 −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) f = 2.2 GHz TA = +25˚C Output Power Pout (dBm) OUTPUT POWER vs. INPUT POWER 10 5 0 −5 − 10 − 15 − 20 − 40 − 35 − 30 − 25 − 20 − 15 − 10 − 5 Input Power Pin (dBm) TA = − 40˚C f = 2.2 GHz VCC = 5.0 V TA = +25 to +85˚C Output Power Pout (dBm) VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V 0 5 10 0 5 10 Output Power (2 tones) Pout (dBm) 3rd Order Intermodulation Distortion IM3 (dBm) 10 Output Power (2 tones) Pout (dBm) 3rd Order Intermodulation Distortion IM3 (dBm) OUTPUT POWER (2 tones), IM3 vs. INPUT POWER f1 = 1 000 MHz 0 f2 = 1 001 MHz Pout 5.5 V VCC = 5.5 V 5.0 V 4.5 V 5.0