Description
www.DataSheet4U.com TPS65050, TPS65051, TPS65052 TPS65054, TPS65056 www.ti.com SLVS710 – JANUARY 2007 6-CHANNEL POWER MGMT IC WITH TWO STEP-DOWN CONVERTERS AND 4 LOW-INPUT VOLTAGE LDOs FEATURES • • Up To 95% Efficiency Output Current for DC/DC Converters: – TPS65050: 2 x 0.6 A – TPS65051: DCDC1 = 1 A; DCDC2 = 0.6 A – TPS65052: DCDC1 = 1 A; DCDC2 = 0.6 A – TPS65054: 2 x 0.6 A – TPS65056: DCDC1 = 1 A; DCDC2 = 0.6 A Output Voltages for DC/DC Converters – TPS65050: Externally Adjustable – TPS65051: Externally Adjustable – TPS65052: DCDC1 = Fixed at 3.3 V; DCDC2 = 1 V / 1.3 V for Samsung Application Processors – TPS65054: DCDC1 = Externally Adjustable; DCDC2 = 1.3 V / 1.05 V for OMAP™1710 Processor – TPS65056: DCDC1 = Fixed at 3.3 V; DCDC2 = 1 V / 1.3 V for Samsung Application Processors VI Range for DC/DC Converters From 2.5 V to 6 V 2.25-MHz Fixed Frequency Operation Power Save Mode at Light Load Current 180° Out-of-Phase Operation Output Voltage Accuracy in PWM mode ±1% Low Ripple PFM Mode Total Typical 32-µA Quiescent Current for Both DC/DC Converters 100% Duty Cycle for Lowest Dropout Two General-Purpose 400-mA, High PSRR LDOs Two General-Purpose 200-mA, High PSRR LDOs VI range for LDOs from 1.5 V to 6.5 V Digital Voltage Selection for the LDOs Available in a 4 mm x 4 mm 32-Pin QFN Package APPLICATIONS • • • • • • Cell Phones, Smart-Phones WLAN PDAs, Pocket PCs OMAP™ and Low-Power TMS320™ DSP Supply Samsung S3C24xx application processor Supply Portable Media Players • DESCRIPTION The TPS6505x are integrated Power Management ICs for applications powered by one Li-Ion or Li-Polymer cell, which require multiple power rails. The TPS6505x provides two efficient, 2.25-MHz step-down converters targeted at providing the core voltage and I/O voltage in a processor based system. Both step-down converters enter a low power mode at light load for maximum efficiency across the widest possible range of load currents. For low noise applications, the devices can be forced into fixed frequency PWM mode by pulling the MODE pin high. In the shutdown mode, the current consumption is reduced to less than 1 µA. The devices allow the use of small inductors and capacitors to achieve a small solution size. TPS6505x provides an output current of up to 1 A on each DC/DC converter. The TPS6505x also integrate two 400-mA LDO and two 200-mA LDO voltage regulators, which can be turned on/off using separate enable pins on each LDO. Each LDO operates with an input voltage range between 1.5 V and 6.5 V allowing them to be supplied from one of the step-down converters or directly from the main battery. Four digital input pins are used to set the output voltage of the LDOs from a set of 16 different combinations for LDO1 to LDO4 on TPS65050 and TPS65052. In TPS65051, TPS65054 and TPS65056, the LDO voltages are adjustable using external resistor dividers. The TPS6505x come in a small 32-pin leadless package (4 mm x 4 mm QFN) with a 0.4 mm pitch. • • • • • • • • • • • • • Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. OMAP, TMS320, PowerPAD are trademarks of Texas Instruments. UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007, Texas Instruments Incorporated TPS65050, TPS65051, TPS65052 TPS65054, TPS65056 www.ti.com SLVS710 – JANUARY 2007 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION TA PART NUMBER TPS65050 TPS65051 TPS65052 -40°C to 85°C TPS65054 OPTION LDO voltages according to Table 1 DC/DC converters externally adjustable LDO voltages externally adjustable DC/DC converters externally adjustable LDO voltages according to Table 1 DCDC1 = 3.3 V; DCDC2 = 1 V / 1.3 V LDO voltages externally adjustable DCDC1 = externally adjustable DCDC2 = 1.3 V / 1.05 V LDO voltages externally adjustable DCDC1 = 3.3 V DCDC2 = 1.0 V / 1.3 V OUTPUT CURRENT for DC/DC CONVERTERS 2 x 600 mA DCDC1 = 1 A DCDC2 = 600 mA DCDC1 = 1 A DCDC2 = 600 mA 2 x 600 mA QFN (1) PACKAGE (2) PACKAGE MARKING 65050 65051 65052 RSM 65054 TPS65056 DCDC1 = 1A DCDC2 = 600 mA 65056 (1) (2) The RSM package is available in tape and reel. Add the R suffix (TPS65050RSMR) to order quantities per reel. Add the T suffix (TPS65050RSMT) to order quantities of 250 parts per reel. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI Web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) UNITS VI Input voltage range on all pins except AGND, PGND, and EN_LDO1 pins with respect to AGND Input voltage range on EN_LDO1 pins with respect to AGND II Current at VINDCDC1/2, L1, PGND1, L2, PGND2 Current at all other pins Continuous total power dissipation TA TJ Tstg (1) Operating free-air temperature Maximum junction temperature Storage temperature range -0.3 V to 7 V -0.3 V to VCC + 0.5 V 1800 mA 1000 mA See the dissipation rating table –40°C to 85°C 125°C –65°C to 150°C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATINGS PACKAGE RSM (1) RθJA (1) 58 K/W POWER RATING TA ≤ 25°C 1.7 W DERATING FACTOR ABOVE TA = 25°C 17 mW/K POWER RATING TA = 70°C 0.95 W POWER RATING TA = 85°C 0.68 W The thermal resistance junction to case of the RSM package is 4 K/W measured on a high K board RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN VI VO VI Input voltage range for step-down converters, VINDCDC1/2 Output voltage range for step-down converter, VDCDC1 Output voltage range for step-down converter, VDCDC2 Input voltage range for LDOs, VINLDO1, VINLDO2, VINLDO3/4 2.5 0.6 0.6 1.5 NOM MAX 6 VINDCDC1/2 VINDCDC1/2 6.5 UNIT V V V V 2 Submit Documentation Feedback TPS65050, TPS65051, TPS65052 TPS65054, TPS65056 www.ti.com SLVS710 – JANUARY 2007 RECOMMENDED OPERATING CONDITIONS (continued) over operating free-air temperature range (unless otherwise noted) MIN VO Output voltage range for LDO1 and LDO2 Output voltage range for LDO3 and LDO4 Output current at L1 (DCDC1) for TPS65051, TPS65052 Output current at L1 (DCDC1) for TPS65050, TPS65054 IO Output current at L1 (DCDC2) Output current at VLDO1, VLDO2 Output current at VLDO3, VLDO4 Inductor at L1, L2 (1) CO Output capacitor at VDCDC1, VDCDC2 (2) Output capacitor at VLDO1, VLDO2, VLDO3, Input capacitor at VCC (2) CI TA TJ Input capacitor at VINLDO1/2 (2) Input capacitor at VINLDO3/4 (2) Operating ambient temperature range Operating junction temperature range Resistor from battery voltage to VCC used for (1) (2) (3) filtering (3) VLDO4 (2) 1.5 10 2.2 1 2.2 2.2 -40 -40 1 85 125 10 2.2 22 1 1 NOM MAX VINLDO1, VINLDO2 VINLDO3/4 1000 600 600 400 200 UNIT V V mA mA mA mA mA µH µF µF µF µF µF °C °C Ω See the Application Information section of this data sheet for more details. See the Application Information section of this data sheet for more details. Up to 2 mA can flow into VCC when both converters are running in PWM, this resistor causes the UVLO threshold to be shifted accordingly. ELECTRICAL CHARACTERISTICS VCC = VINDCDC1/2 = 3.6 V, EN = VCC, MODE = GND, L = 2.2 µH, CO = 10 µF. TA = -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted). PARAMETER SUPPLY CURRENT VI Input voltage range at VINDCDC1/2 One converter, IO = 0 mA. PFM mode enabled (Mode = GND) device not switching, EN_DCDC1 = VI OR EN_DCDC2 = VI; EN_LDO1= EN_LDO2 = EN_LDO3/4 = GND Operating quiescent current Total current into VCC, VINDCDC1/2, VINLDO1, VINLDO2, VINLDO3/4 Two converters, IO = 0 mA PFM mode enabled (Mode = 0) device not switching, EN_DCDC1 = VI AND EN_DCDC2 = VI; EN_LDO1 = EN_LDO2 = EN_LDO3/4 = GND One converter, IO = 0 mA. PFM mode enabled (Mode = GND) device not switching, EN_DCDC1 = VI OR EN_DCDC2 = VI; EN_LDO1 = EN_LDO2 = EN_LDO3 = EN_LDO4 = VI One converter, IO = 0 mA. Switching with no load (Mode = VI), PWM operation EN_DCDC1 = VI OR EN_DCDC2 = VI; EN_LDO1 = EN_LDO2 = EN_LDO3/4 = GND Two converters, IO = 0 mA Switching with no load (Mode = VI), PWM operation EN_DCDC1 = VI AND EN_DCDC2 = VI; EN_LDO1 = EN_LDO2 = EN_LDO3/4 = GND EN_DCDC1 = EN_DCDC2 = GND EN_LDO1 = EN_LDO2 = EN_LDO3 = EN_LDO4 = GND Voltage at VCC 2.5 6 V µA TEST CONDITIONS MIN TYP MAX UNIT 20 30 IQ 32 40 µA 180 250 µA 0.85 mA IQ Operating quiescent current into VCC 1.25 mA I(SD) V(UVLO) Shutdown current Undervoltage lockout threshold for DCDC converters and LDOs 9 1.8 12 2 µA V Submit Documentation Feedback 3 TPS65050, TPS65051, TPS65052 TPS65054, TPS65056 www.ti.com SLVS710 – JANUARY 2007 ELECTRICAL CHARACTERISTICS (continued) VCC = VINDCDC1/2 = 3.6 V, EN = VCC, MODE = GND, L = 2.2 µH, CO = 10 µF. TA = -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT EN_DCDC1, EN_DCDC2, DEFDCDC2, DEFLDO1, DEFLDO2, DEFLDO3, DEFLDO4, EN_LDO1, EN_LDO2, EN_LDO3, EN_LDO4 MODE/DATA, EN_DCDC1, EN_DCDC2, DEFDCDC2, DEFLDO1, DEFLDO2, DEFLDO3, DEFLDO4, EN_LDO1, EN_LDO2, EN_LDO3, EN_LDO4 MODE/D

Part Number
TPS65056

Free Sample / Buy Component / Product Information
Locate Part TPS65056

Datasheet
Locate DataSheet

TPS65056 Cross Reference : Jump New Window
Get Cross-Reference Datasheet