Charge Pump Voltage Converters

Charge Pump Voltage Converters FEATURES • • • • • • Simple Conversion of +5V Logic Supply to ±5V Supplies Simple Voltage Multiplication (VOUT = (-) nVIN) Typical Open Circuit Voltage Conversion Efficiency 99.9% Typical Power Efficiency 98% Wide Operating Voltage Range- TJ7660 1.5V to 10.0V Easy to Use - Requires Only 2 External Non-Critical Passive Components • No External Diode Over Full Temp. and Voltage Range TJ7660 SOP-8 PKG DIP-8 PKG APPLICATION • • • • On Board Negative Supply for Dynamic RAMs Localized µProcessor (8080 Type) Negative Supplies Inexpensive Negative Supplies Data Acquisition Systems < Pin Configuration ORDERING INFORMATION Device www.DataSheet4U.com Package SOP-8 D I P-8 TJ7660D TJ7660N DESCRIPTION The HTC TJ7660 is a monolithic CMOS power supply circuit which offers unique performance advantages over previously available devices. The TJ7660 performs supply voltage conversions from positive to negative for an input range of +1.5V to +10.0V resulting in complementary output voltages of -1.5V to -10.0V. Only 2 noncritical external capacitors are needed for the charge pump and charge reservoir functions. The TJ7660 can also be connected to function as voltage doublers and will generate output voltages up to +18.6V with a +10V input. Contained on the chip are a series DC supply regulator, RC oscillator, voltage level translator, and four output power MOS switches. A unique logic element senses the most negative voltage in the device and ensures that the output N-Channel switch source-substrate junctions are not forward biased. This assures latchup free operation. The oscillator, when unloaded, oscillates at a nominal frequency of 10kHz for an input supply voltage of 5.0V. This frequency can be lowered by the addition of an external capacitor to the “OSC” terminal, or the oscillator may be overdriven by an external clock. The “LV” terminal may be tied to GROUND to bypass the internal series regulator and improve ( ) ( ) Jan. 2007-Rev 1.0 1 HTC Charge Pump Voltage Converters Absolute Maximum Ratings Supply Voltage TJ7660 LV and OSC Input Voltage (Note2) Current into LV (Note 2) Output Short Duration (VSUPPLY ≤ 5.5V) Operating Ambient Temperature +10.5V -0.3V to [(V+ +0.3V) for V+] < 5.5V (V+ -5.5V) to [(V+ +0.3V) for V+] > 5.5V 20µA for V+ > 3.5V Continuous 0℃ to 70℃ TJ7660 V V uA ℃ Thermal Information Thermal Resistance (Typical, Note 1) PDIP Package SOIC Package Metal Can Package (TJ7660 Only) Maximum Storage Temperature Range Maximum Lead Temperature (Soldering, 10s) (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. θJA (℃/W) 150 165 160 -65oC to 150℃ 300℃ θJC (℃/W) N/A N/A 70 ELECTRICAL CHARACTERISTIC (TJ7660, V+ = 5V, TA = 25oC, COSC = 0, unless Otherwise Specified TJ7660 PARAMETER Supply Current Supply Voltage Range -Lo Supply Voltage Range -Hi Output Source Resistance SYMBOL I+ VL+ VH+ ROUT TEST CONDITIONS RL = ∞ MIN ≤ TA ≤ MAX, RL =10kΩ, LV to GND UNITS MIN 2.0 3 - TYP 100 60 - MAX 180 3.5 100 300 400 µA V V Ω Ω Ω Ω kHz % % MIN ≤ TA ≤ MAX, RL =10kΩ,LVto Open IOUT =20mA, TA =25℃ IOUT =20mA, -40℃ ≤ TA ≤ 85℃ V+ = 2V, IOUT = 3mA, LV to GND 0℃≤ TA ≤ 70℃ V+ = 2V, IOUT = 3mA, LV to GND, -55℃ ≤ TA ≤ 125℃ Oscillator Frequency Power Efficiency NOTES fOSC PEF RL =5kΩ RL = ∞ 95 98 10 98 99.9 - Voltage Conversion Efficie VOUT EF 1. θJA is measured with the component mounted on an evaluation PC board in free air. 2. Connecting any input terminal to voltages greater than V+ or less than GND may cause destructive latchup. It is recommended that no inputs from sources operating from external supplies be applied prior to “power up” of the TJ7660. Jan. 2007-Rev 1.0 2 HTC Charge Pump Voltage Converters Test Circuit TJ7660 TJ7660 NOTE: For large values of COSC (>1000pF) the values of C1 and C2 should be increased to 100µF. BLOCK DIAGRAM Jan. 2007-Rev 1.0 3 HTC Charge Pump Voltage Converters Typical Performance Curves Output Resistance vs. Supply Voltage TJ7660 10000 Output Resistance(Ohm) 1000 100 10 1 2 3 4 5 Supply Voltage(v) 6 7 8 Output Load vs. Load Current(V +=+5) 130 Output Load(Ohm) 120 110 100 90 80 0 1 5 10 Load Current(mA) 15 20 25 Power Convension Efficiency vs.Load Current(V+=+5V) 100 90 80 70 60 50 40 30 20 10 0 5 10 15 Load Current(mA) 20 25 30 Power Convention Efficiency(%) NOTE: 6. These curves include in the supply current that current fed directly into the load RL from the V+ (See Figure 11). Thus, approximately half the supply current goes directly to the positive side of the load, and the other half, through the TJ7660, to the negative side of the load. Ideally, VOUT = 2VIN, IS = 2IL, so VIN x IS = VOUT x IL. Jan. 2007-Rev 1.0 4 HTC Charge Pump Voltage Converters TJ7660 Detailed Description The TJ7660 contains all the necessary circuitry to complete a negative voltage converter, with the exception of 2 external capacitors which may be inexpensive 10µF polarized electrolytic types. The mode of operation of the device may be best understood by considering Figure12, which shows an idealized negative voltage converter. Capacitor C1 is charged to a voltage, V+, for the half cycle when switches S1 and S3 are closed. (Note: Switches S2 and S4 are open during this half cycle.) During the second halfcycle of operation, switches S2 and S4 are closed, with S1 and S3 open, thereby shifting capacitor C1 negatively by V+ volts. Charge is then transferred from C1 to C2 such that the voltage on C2 is exactly V+, assuming ideal switches and no load on C2. The TJ 7660 approaches this ideal situation more closely than existing non-mechanical circuits. In the TJ7660, the 4 switches of Figure 12 are MOS power switches; S1 is a P-Channel device and S2, S3 and S4 are N-Channel devices. The main difficulty with this approach is that in integrating the switches, the substrates of S3 and S4 must always remain reverse biased with respect to their sources, but not so much as to degrade their “ON” resistances. In addition, at circuit start-up, and under output short circuit conditions (VOUT = V+), the output voltage must be sensed and the substrate bias adjusted accordingly. Failure to accomplish this would result in high power losses and probable device latchup. This problem is eliminated in the TJ7660 by a logic network which senses the output voltage (VOUT) together with the level translators, and switches the substrates of S3 and S4 to the correct level to maintain necessary reverse bias. The voltage regulator portion of the TJ7660 is an integral part of the anti-latchup circuitry, however its inherent voltage drop can degrade operation at low voltages. Therefore, to improve low voltage operation the “LV” pin should be connected to GROUND, disabling the regulator. For supply voltages greater than 3.5V the LV terminal must be left open to insure latchup proof operation, and prevent device damage. Theoretical Power Efficiency Considerations In theory a voltage converter can approach 100% efficiency if certain conditions are met. 1. The driver circuitry consumes minimal power. 2. The output switches have extremely low ON resistance and virtually no offset. 3. The impedances of the pump and reservoir capacitors are negligible at the pump frequency. The TJ7660 approaches these conditions for negative voltage conversion if large values of C1 and C2 are used. ENERGY IS LOST ONLY IN THE TRANSFER OF CHARGE BETWEEN CAPACITORS IF A CHANGE IN VOLTAGE OCCURS. The energy lost is defined by:E = 1/2 C1 (V12 - V22) where V1 and V2 are the voltages on C1 during the pump and transfer cycles. If the impedances of C1 and C2 are relatively high at the pump frequency (refer to Figure 12) compared to the value of RL, there will be a substantial difference in the voltages V1 and V2. Therefore it is not only desirable to make C2 as large as possible to eliminate output voltage ripple, but also to employ a correspondingly large value for C1 in order to achieve maximum efficiency of operation. Jan. 2007-Rev 1.0 5 HTC Charge Pump Voltage Converters TJ7660 Do’s And Don’ts 1. Do not exceed maximum supply voltages. 2. Do not connect LV terminal to GROUND for supply voltages greater than 3.5V. 3. Do not short circuit the output to V+ supply for supply voltages above 5.5V for extended periods, however, transient conditions including start-up are okay. 4. When using polarized capacitors, the + terminal of C1 must be connected to pin 2 of the TJ7660 and the + terminal of C2 must be connected to GROUND. 5. If the voltage supply driving the TJ7660 has a large source impedance (25Ω - 30Ω), then a 2.2µF capacitor from pin 8 to ground may be required to limit rate of rise of input voltage to less than 2V/µ s. 6. User should insure that the output (pin 5) does not go more positive than GND (pin 3). Device latch up will occur under these conditions. A 1N914 or similar diode placed in parallel with C2 will prevent the device from latching up under these conditions. (Anode pin 5, Cathode pin 3). TJ7660 TJ7660 TJ7660 Jan. 2007-Rev 1.0 6 HTC Charge Pump Voltage Converters TJ7660 TJ7660 TJ7660 Typical Applications Simple Negative Voltage Converter Themajority of applications will undoubtedly utilize the TJ7660 for generation of negative supply voltages. Figure 13 shows typical connections to provide a negative supply negative (GND) for supply voltages below 3.5V. The output characteristics of the circuit in Figure 13A can be approximated by an ideal voltage source in series with a resistance as shown in Figure 13B. The voltage source has a value of -V+. The output impedance (RO) is a function of the ON