PHASE CONTROL THYRISTORS Hockey Puk Version

Previous Datasheet www.DataSheet4U.com Index Next Data Sheet DISCRETE POWER DIODES and THYRISTORS DATA BOOK D-366 To Order Previous Datasheet Index Next Data Sheet Bulletin I25168/B ST380C..C SERIES PHASE CONTROL THYRISTORS Hockey Puk Version Features Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (E-PUK) Low profile hockey-puk to increase current-carrying capability 960A Typical Applications DC motor controls Controlled DC power supplies AC controllers Major Ratings and Characteristics Parameters IT(AV) @ Ths IT(RMS) @ Ths ITSM @ 50Hz @ 60Hz I t 2 case style TO-200AB (E-PUK) Units A °C A °C A A KA2s KA2s V µs °C ST380C..C 960 55 1900 25 15000 15700 1130 1030 400 to 600 @ 50Hz @ 60Hz V DRM /V RRM tq TJ typical 100 - 40 to 125 D-367 To Order Previous Datasheet Index Next Data Sheet ST380C..C Series ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage Type number Code 04 ST380C..C 06 600 700 V DRM /V RRM , max. repetitive peak and off-state voltage V 400 VRSM , maximum nonrepetitive peak voltage V 500 I DRM /I RRM max. @ TJ = TJ max mA 50 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature I T(RMS) Max. RMS on-state current I TSM Max. peak, one-cycle non-repetitive surge current ST380C..C 960 (440) 55 (75) 1900 15000 15700 12600 13200 Units Conditions A °C 180° conduction, half sine wave double side (single side) cooled DC @ 25°C heatsink temperature double side cooled t = 10ms A t = 8.3ms t = 10ms t = 8.3ms t = 10ms KA2s t = 8.3ms t = 10ms t = 8.3ms KA2√s No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max. 12 I2 t Maximum I2t for fusing 1130 1030 800 725 I 2 √t Maximum I2√t for fusing 11300 0.85 t = 0.1 to 10ms, no voltage reapplied (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. V T(TO) 1 Low level value of threshold voltage V T(TO) 2 High level value of threshold voltage rt1 rt2 V TM IH IL Low level value of on-state slope resistance High level value of on-state slope resistance Max. on-state voltage Maximum holding current Typical latching current V 0.88 (I > π x IT(AV)),TJ = TJ max. (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. mΩ 0.24 1.60 600 mA 1000 T J = 25°C, anode supply 12V resistive load V (I > π x IT(AV)),TJ = TJ max. 0.25 2222222222222 I = 3000A, TJ = TJ max, t = 10ms sine pulse pk p Switching Parameter di/dt Max. non-repetitive rate of rise of turned-on current t t d ST380C..C 1000 1.0 Units Conditions A/µs Gate drive 20V, 20Ω, t ≤ 1µs TJ = TJ max, anode voltage ≤ 80% VDRM Gate current 1A, di /dt = 1A/µs g r Typical delay time Typical turn-off time µs q V = 0.67% VDRM, TJ = 25°C d 100 ITM = 550A, TJ = TJ max, di/dt = 40A/µs, VR = 50V dv/dt = 20V/µs, Gate 0V 100Ω, t = 500µs p D-368 To Order Previous Datasheet Index Next Data Sheet ST380C..C Series Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics Fig. 5- On-state Power Loss Characteristics Fig. 6- On-state Power Loss Characteristics Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled D-372 To Order Previous Datasheet Index Next Data Sheet ST380C..C Series Fig. 9 - On-state Voltage Drop Characteristics Fig. 10 - Thermal Impedance Z thJ-hs Characteristics Fig. 11 - Gate Characteristics D-373 To Order Previous Datasheet Index Next Data Sheet ST380C..C Series Blocking Parameter dv/dt IRRM IDRM Maximum critical rate of rise of off-state voltage Max. peak reverse and off-state leakage current ST380C..C 500 50 Units Conditions V/µs mA TJ = TJ max. linear to 80% rated VDRM TJ = TJ max, rated V DRM/V RRM applied Triggering Parameter PGM Maximum peak gate power ST380C..C 10.0 2.0 3.0 20 Units Conditions W A TJ = TJ max, t ≤ 5ms p PG(AV) Maximum average gate power IGM +VGM -VGM Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage TYP. 200 IGT DC gate current required to trigger 100 50 2.5 VGT DC gate voltage required to trigger IGD VGD DC gate current not to trigger DC gate voltage not to trigger 1.8 1.1 TJ = TJ max, f = 50Hz, d% = 50 TJ = TJ max, t ≤ 5ms p V 5.0 MAX. 200 3.0 10 0.25 mA V V mA TJ = TJ max, t ≤ 5ms p 23 TJ = - 40°C TJ = 25°C TJ = 125°C TJ = - 40°C TJ = 25°C TJ = 125°C Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied TJ = TJ max Thermal and Mechanical Specification Parameter TJ T stg ST380C..C -40 to 125 -40 to 150 0.09 0.04 0.02 0.01 9800 (1000) Units °C Conditions Max. operating temperature range Max. storage temperature range RthJ-hs Max. thermal resistance, junction to heatsink RthC-hs Max. thermal resistance, case to heatsink F Mounting force, ± 10% DC operation single side cooled K/W DC operation double side cooled DC operation single side cooled DC operation double side cooled N (Kg) g See Outline Table K/W wt Approximate weight Case style 83 TO - 200AB (E-PUK) D-369 3333 To Order Previous Datasheet Index Next Data Sheet ST380C..C Series ∆RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Conduction angle 180° 120° 90° 60° 30° Sinusoidal conduction Single Side Double Side 0.010 0.012 0.015 0.022 0.036 0.011 0.012 0.015 0.022 0.036 Rectangular conduction Single Side Double Side 0.007 0.012 0.016 0.023 0.036 0.007 0.013 0.017 0.023 0.037 Units Conditions TJ = TJ max. K/W 12 Ordering Information Table Device Code ST 1 38 2 0 3 C 4 06 5 C 6 1 7 8 1 2 3 4 5 6 7 - Thyristor Essential part number 0 = Converter grade C = Ceramic Puk Voltage code: Code x 100 = VRRM (See Voltage Rating Table) C = Puk Case TO-200AB (E-PUK) 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 2222222222222 8 - Critical dv/dt: None = 500V/µsec (Standard selection) L = 1000V/µsec (Special selection) D-370 To Order Previous Datasheet Index Next Data Sheet ST380C..C Series Outline Table ANODE TO GATE CREEPAGE DISTANCE: 11.18 (0.44) MIN. STRIKE DISTANCE: 7.62 (0.30) MIN. 25.3 (0.99) DIA. MAX. 0.3 (0.01) MIN. 14.1 / 15.1 (0.56 / 0.59) 0.3 (0.01) MIN. 25.3 (0.99) DIA. MAX. 40.5 (1.59) DIA. MAX. GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE Case Style TO-200AB (E-PUK) All dimensions in millimeters (inches) 2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP 6.5 (0.26) 4.75 (0.19) 23 25°± 5° 42 (1.65) MAX. 28 (1.10) Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics D-371 3333 To Order