http://www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf


Siemens
Siemens

S7300 Datasheet

CPU 31xC and CPU 31x


S7300 Datasheet Preview


SIMATIC
S7-300www.DataSheet4U.com
CPU 31xC and CPU 31x,
Technical data
Manual
Preface
Guide to the S7-300
documentation
Operating and display
elements
Communication
Memory concept
Cycle and reaction times
Technical data of CPU 31xC
Technical data of CPU 31x
Appendix
1
2
3
4
5
6
7
A
This manual is part of the documentation package
with the order number: 6ES7398-8FA10-8BA0
Edition 08/2004
A5E00105475-05
Page 1

Safety Guidelines
This manual contains notices which you should observe to ensure your own personal safety as well as to avoid
property damage. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring to property damage only have no safety alert symbol.
Danger
indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Warning
indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
www.DataSheet4U.com
Caution
used with the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Caution
used without safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
Notice
used without the safety alert symbol indicates a potential situation which, if not avoided, may result in
an undesirable result or state.
When several danger levels apply, the notices of the highest level (lower number) are always displayed. If a
notice refers to personal damages with the safety alert symbol, then another notice may be added warning of
property damage.
Qualified Personnel
The device/system may only be set up and operated in conjunction with this documentation. Only qualified
personnel should be allowed to install and work on the equipment. Qualified persons are defined as persons who
are authorized to commission, to earth, and to tag circuits, equipment and systems in accordance with
established safety practices and standards.
Intended Use
Please note the following:
Warning
This device and its components may only be used for the applications described in the catalog or
technical description, and only in connection with devices or components from other manufacturers
approved or recommended by Siemens.
This product can only function correctly and safely if it is transported, stored, set up and installed
correctly, and operated and maintained as recommended.
Trademarks
All designations marked with ® are registered trademarks of Siemens AG. Other designations in this
documentation might be trademarks which, if used by third parties for their purposes, might infringe upon the
rights of the proprietors.
Copyright Siemens AG ,2004.All rights reserved
Reproduction, transmission or use of this document or its contents is not permitted without
express written authority. Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or design, are reserved.
Siemens AG
Automation and Drives Group
P.O. Box 4848, D-90327 Nuremberg (Germany)
Siemens Aktiengesellschaft
Disclaimer of Liability
We have checked the contents of this manual for agreement with the hardware and
software described. Since deviations cannot be precluded entirely, we cannot guarantee
full agreement. However, the data in the manual are reviewed regularly, and any
necessary corrections will be included in subsequent editions. Suggestions for
improvement are welcomed.
Siemens AG 2004
Technical data subject to change
Order No. A5E00105475-05
Page 2

Preface
www.DataSheetP4Uu.rcpomose of the Manual
This manual contains all the information you will need concerning the configuration,
communication, memory concept, cycle, response times and technical data for the CPUs.
You will then learn the points to consider when upgrading to one of the CPUs discussed in
this manual.
Required basic knowledge
To understand this manual, you require a general knowledge of automation engineering.
You should also be accustomed to working with STEP 7 basic software.
Area of application
Table 1-1 Application area covered by this manual
CPU
Convention:
CPU designations:
Order number
CPU 312C
CPU 313C
CPU 313C-2 PtP
CPU 313C-2 DP
CPU 314C-2 PtP
CPU 314C-2 DP
CPU 312
CPU 314
CPU 315-2 DP
CPU 315-2 PN/DP
CPU 317-2 DP
CPU 317-2 PN/DP
CPU 31xC
CPU 31x
6ES7312-5BD01-0AB0
6ES7313-5BE01-0AB0
6ES7313-6BE01-0AB0
6ES7313-6CE01-0AB0
6ES7314-6BF01-0AB0
6ES7314-6CF01-0AB0
6ES7312-1AD10-0AB0
6ES7314-1AF10-0AB0
6ES7315-2AG10-0AB0
6ES7315-2EG10-0AB0
6ES7317-2AJ10-0AB0
6ES7317-2EJ10-0AB0
as of version
Firmware Hardware
V2.0.0
01
V2.0.0
01
V2.0.0
01
V2.0.0
01
V2.0.0
01
V2.0.0
01
V2.0.0
01
V2.0.0
01
V2.0.0
01
V2.3.0
01
V2.1.0
01
V2.3.0
01
Note
The special features of the CPU 315F-2 DP (6ES7 315-6FF00-0AB0) and CPU 317F-2 DP
(6ES7 317-6FF00-0AB0) are described in their Product Information, available on the Internet
at
http://www.siemens.com/automation/service&support, article ID 17015818.
CPU 31xC and CPU 31x, Technical data
Manual, Edition 08/2004, A5E00105475-05
iii
Page 3
Part Number S7300
Manufactur Siemens
Description CPU 31xC and CPU 31x
Total Page 30 Pages
PDF Download
S7300 datasheet
Download PDF File
S7300 datasheet
View Html for PC & Mobile


Related Datasheet

S7300 , S7300 , S7300 , S7300 , S7300 ,

site map

webmaste! click here

contact us

Buy Components