www.DataSheet4U.com
RF3140
0
Pb-Free Product Typical Applications • 3V Quad-Band GSM Handsets • Commercial and Consumer Systems • Portable Battery-Powered Equipment Product Description
The RF3140 is a high-power, high-efficiency power amplifier module with integrated power control. The device is self-contained with 50Ω input and output terminals. The power control function is also incorporated, eliminating the need for directional couplers, detector diodes, power control ASICs and other power control circuitry; this allows the module to be driven directly from the DAC output. The device is designed for use as the final RF amplifier in GSM850, EGSM900, DCS and PCS handheld digital cellular equipment and other applications in the 824MHz to 849MHz, 880MHz to 915MHz, 1710MHz to 1785MHz and 1850MHz to 1910MHz bands. On-board power control provides over 50dB of control range with an analog voltage input; and, power down with a logic “low” for standby operation. Optimum Technology Matching® Applied
Si BJT Si Bi-CMOS InGaP/HBT GaAs HBT SiGe HBT GaN HEMT GaAs MESFET Si CMOS SiGe Bi-CMOS
9.600 TYP 8.800 TYP 8.200 TYP 7.400 TYP 6.800 TYP 6.000 TYP 5.400 TYP 4.600 TYP 4.000 TYP 3.200 TYP 2.600 TYP 1.800 TYP 1.200 TYP 0.400 TYP 0.000 9.098 TYP 0.000 1.797 8.205 8.280
QUAD-BAND GSM850/GSM900/DCS/PCS POWER AMP MODULE
• GSM850/EGSM900/DCS/PCS Products • GPRS Class 12 Compatible • Power StarTM Module
5.400 TYP 6.000 TYP 6.800 TYP 7.400 TYP 8.200 TYP 8.275 TYP 8.800 TYP 9.600 TYP Pin 1 8.747
0.400 TYP
1.200 TYP 1.800 TYP
2.600 TYP
3.200 TYP 4.000 TYP 4.600 TYP
5.925 4.075
1.245 0.306
Pin 1
1.70 1.45
10.00 ± 0.10
10.00 ± 0.10
0.450 ± 0.075
Package Style: Module (10mmx10mm)
Features • Complete Power Control Solution • Single 3.0V to 5.5V Supply Voltage • +35dBm GSM Output Power at 3.5V • +33dBm DCS/PCS Output Power at 3.5V
12 DCS/PCS IN 1 BAND SELECT 2 TX ENABLE 3 VBATT 4 VREG 5 VRAMP 6 GSM850/GSM900 IN 7 8 VCC2 9 GSM850/GSM900 OUT 10 VCC OUT 11 DCS/PCS OUT
VCC2
• 60% GSM and 55% DCS/PCS ηEFF • 10mmx10mm Package Size
Ordering Information
RF3140 Quad-Band GSM850/GSM900/DCS/PCS Power Amp Module RF3140 Power Amp Module 5-Piece Sample Pack RF3140PCBA-41XFully Assembled Evaluation Board RF Micro Devices, Inc. 7628 Thorndike Road Greensboro, NC 27409, USA Tel (336) 664 1233 Fax (336) 664 0454 http://www.rfmd.com
Functional Block Diagram
Rev A9 060217
2-491
RF3140
Absolute Maximum Ratings Parameter
Supply Voltage Power Control Voltage (VRAMP) Input RF Power Max Duty Cycle Output Load VSWR Operating Case Temperature Storage Temperature
Rating
-0.3 to +6.0 -0.3 to +1.8 +8.5 50 10:1 -20 to +85 -55 to +150
Unit
VDC V dBm % °C °C Caution! ESD sensitive device.
RF Micro Devices believes the furnished information is correct and accurate at the time of this printing. However, RF Micro Devices reserves the right to make changes to its products without notice. RF Micro Devices does not assume responsibility for the use of the described product(s).
Parameter
Overall Power Control VRAMP
Power Control “ON” Power Control “OFF” VRAMP Input Capacitance VRAMP Input Current Turn On/Off Time
Specification Min. Typ. Max.
Unit
Condition
0.2 15
1.5 0.25 20 10 2
V V pF μA μs V V μA mA V mA μA V V μA V V μA
Max. POUT, Voltage supplied to the input Min. POUT, Voltage supplied to the input DC to 2MHz VRAMP =VRAMP MAX VRAMP =0.2V to VRAMP MAX Specifications Nominal operating limits PIN <-30dBm, TX Enable=Low, Temp=-20°C to +85°C VRAMP =0.2V, TX Enable=High TX Enable=High TX Enable=Low
Overall Power Supply
Power Supply Voltage 3.0 Power Supply Current 1 3.5 5.5 10 150 2.9 8
VREG Voltage VREG Current
2.7
2.8 7 10 0 2.0 20 0 2.0 1
Overall Control Signals
Band Select “Low” Band Select “High” Band Select “High” Current TX Enable “Low” TX Enable “High” TX Enable “High” Current 0 1.9 0 1.9 0.5 3.0 50 0.5 3.0 2
2-492
Rev A9 060217
RF3140
Parameter Specification Min. Typ. Max. Unit Condition
Temp=+25 °C, VBATT =3.5V, VRAMP =VRAMP MAX, PIN =3dBm, VREG =2.8V, Freq=824MHz to 849MHz, 25% Duty Cycle, Pulse Width=1154μs +34.2 32 Total Efficiency Input Power Range Output Noise Power Forward Isolation 1 Forward Isolation 2 Cross Band Isolation at 2f0 Second Harmonic Third Harmonic All Other Non-Harmonic Spurious Input Impedance Input VSWR Output Load VSWR Stability Output Load VSWR Ruggedness Output Load Impedance 45 0 824 to 849 +35.0 33 55 +3 -86 -35 -25 -30 -15 -30 MHz dBm dBm % dBm dBm dBm dBm dBm dBm dBm dBm Ω 2.5:1 8:1 10:1 50 55 Ω dB VRAMP =0.2V to VRAMP MAX Spurious<-36dBm, RBW=3MHz Set VRAMP where VRAMP <34.2dBm into 50Ω load Load impedance presented at RF OUT pad VRAMP =0.2V to VRAMP MAX Temp = 25°C, VBATT =3.5V, VRAMP =VRAMP MAX Temp=+85 °C, VBATT =3.0V, VRAMP =VRAMP MAX At POUT MAX, VBATT =3.5V Maximum output power guaranteed at minimum drive level RBW=100kHz, 869MHz to 894MHz, POUT > +5dBm TXEnable=Low, 0V, PIN =+5dBm TXEnable=High, PIN =+5dBm, VRAMP =0.2V VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX
Overall (GSM850 Mode)
Operating Frequency Range Maximum Output Power
+5 -84 -25 -10 -20 -5 -10 -36
50
Power Control VRAMP
Power Control Range Note: VRAMP MAX =3/8*VBATT +0.18<1.5V
Rev A9 060217
2-493
RF3140
Parameter Specification Min. Typ. Max. Unit Condition
Temp=+25 °C, VBATT =3.5V, VRAMP =VRAMP MAX, PIN =3dBm, VREG =2.8V, Freq=880MHz to 915MHz, 25% Duty Cycle, Pulse Width=1154μs +34.2 32 Total Efficiency Input Power Range Output Noise Power 52 0 880 to 915 +35.0 33 58 +3 -86 -88 Forward Isolation 1 Forward Isolation 2 Cross Band Isolation 2f0 Second Harmonic Third Harmonic All Other Non-Harmonic Spurious Input Impedance Input VSWR Output Load VSWR Stability Output Load VSWR Ruggedness Output Load Impedance -35 -25 -24 -15 -30 MHz dBm dBm % dBm dBm dBm dBm dBm dBm dBm dBm dBm Ω 2.5:1 8:1 10:1 50 50 Ω dB VRAMP =0.2V to VRAMP MAX Spurious<-36dBm, RBW=3MHz Set VRAMP where VRAMP <34.2dBm into 50Ω load Load impedance presented at RF OUT pad VRAMP =0.2V to VRAMP MAX Temp = 25°C, VBATT =3.5V, VRAMP =VRAMP MAX Temp=+85 °C, VBATT =3.0V, VRAMP =VRAMP MAX At POUT MAX, VBATT =3.5V Maximum output power guaranteed at minimum drive level RBW=100kHz, 925MHz to 935MHz, POUT > +5dBm RBW=100kHz, 935MHz to 960MHz, POUT > +5dBm TXEnable=Low, 0V, PIN =+5dBm TXEnable=High, VRAMP =0.2V, PIN =+5dBm VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX
Overall (GSM900 Mode)
Operating Frequency Range Maximum Output Power
+5 -82 -84 -25 -10 -20 -5 -10 -36
50
Power Control VRAMP
Power Control Range Note: VRAMP MAX =3/8*VBATT +0.18<1.5V
2-494
Rev A9 060217
RF3140
Parameter Specification Min. Typ. Max. Unit Condition
Temp=25°C, VBATT =3.5V, VRAMP =VRAMP MAX, PIN =3dBm, VREG =2.8V, Freq=1710MHz to 1785MHz, 25% Duty Cycle, pulse width=1154μs +32 +29.5 Total Efficiency Input Power Range Output Noise Power Forward Isolation 1 Forward Isolation 2 Second Harmonic Third Harmonic All Other Non-Harmonic Spurious Input Impedance Input VSWR Output Load VSWR Stability Output Load VSWR Ruggedness Output Load Impedance 48 0 1710 to 1785 +33 +31.0 55 +3 -85 -40 -20 -15 -30 MHz dBm dBm % dBm dBm dBm dBm dBm dBm dBm Ω 2.5:1 VRAMP =0.2V to VRAMP MAX Spurious<-36dBm, RBW=3MHz Set VRAMP where VRAMP <34.2dBm into 50Ω load Load impedance presented at RF OUT pin VRAMP =0.2V to VRAMP MAX, PIN =+5dBm Temp=25°C, VBATT =3.5V, VRAMP =VRAMP MAX Temp=+85°C, VBATT =3.0V, VRAMP =VRAMP MAX At POUT MAX, VBATT =3.5V Maximum output power guaranteed at minimum drive level RBW=100kHz, 1805MHz to 1880MHz, POUT > 0dBm, VBATT =3.5V TXEnable=Low, 0V, PIN =+5dBm TXEnable=High, VRAMP =0.2V, PIN =0dBm to +5dBm VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX
Overall (DCS Mode)
Operating Frequency Range Maximum Output Power
+5 -80 -30 -10 -7 -15 -36
50 8:1 10:1 50 50
Ω dB
Power Control VRAMP
Power Control Range Note: VRAMP MAX =3/8*VBATT +0.18<1.5V
Rev A9 060217
2-495
RF3140
Parameter Specification Min. Typ. Max. Unit Condition
Temp=25°C, VBATT =3.5V, VRAMP =VRAMP MAX, PIN =3dBm, VREG =2.8V, Freq=1850MHz to 1910MHz, 25% Duty Cycle, pulse width=1154μs +32 +29.5 Total Efficiency Input Power Range Output Noise Power Forward Isolation 1 Forward Isolation 2 Second Harmonic Third Harmonic All Other Non-Harmonic Spurious Input Impedance Input VSWR Output Load VSWR Stability Output Load VSWR Ruggedness Output Load Impedance 45 0 1850 to 1910 +33 +31.0 52 +3 -85 -40 -20 -15 -30 MHz dBm dBm % dBm dBm dBm dBm dBm dBm dBm Ω 2.5:1 VRAMP =0.2V to VRAMP MAX Spurious<-36dBm, VRAMP =0.2V to VRAMP MAX, RBW=3MHz Set VRAMP where VRAMP <34.2dBm into 50Ω load Load impedance presented at RF OUT pin VRAMP =0.2V to VRAMP MAX, PIN =+5dBm Temp=25°C, VBATT =3.5V, VRAMP =VRAMP MAX, 1850MHz to 1910MHz Temp=+85°C, VBATT =3.0V, VRAMP =VRAMP MAX At POUT MAX, VBATT =3.5V Full output power guaranteed at minimum drive level RBW=100kHz, 1930MHz to 1990MHz, POUT > 0dBm, VBATT =3.5V TX_ENABLE=Low, PIN =+5dBm TXEnable=High, VRAMP =0.2V, PIN =+5dBm VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX VRAMP =0.2V to VRAMP MAX
Overall (PCS Mode)
Operating Frequency Range Maximum Output Power
+5 -80 -30 -10 -7 -15 -36
50 8:1 10:1 50 50
Ω dB
Power Control VRAMP
Power Control Range Note: VRAMP MAX =3/8*VBATT +0.18<1.5V
2-496
Rev A9 060217
RF3140
Pin 1 2 3 4 5 6 7 8 9 10 Function Description DCS/PCS IN RF input to the DCS/PCS band. This is a 50Ω input. Allows external control to select the GSM or DCS/PCS bands with a BAND logic high or low. A logic low enables the GSM bands, whereas a logic SELECT high enables the DCS/PCS bands. TX ENABLE VBATT VREG VRAMP GSM850/GS M900 IN VCC2 GSM850/GS M900 OUT VCC OUT
This signal enables the PA module for operation with a logic high. Once TX Enable is asserted the RF output level will increase to -20dBm. Power supply for the module. This should be connecte
