PI3HDMI412FT (Pericom Semiconductor) - DVI/HDMI Compliant Signal Switch

Part Number	PI3HDMI412FT
Manufacturer	Pericom Semiconductor
Semiconductor DataSheet
DataSheet View

www.DataSheet4U.com PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out Features • • • • • • • • • • • • • 4-Differential Channel 2:1 Mux/DeMux DVI, HDMI rev 1.1, and HDMI rev 1.2 signal compatible -3dB BW = 1.5 GHz (3.0Gbps) Crosstalk: -35dB@1.65Gbps Switching speed: 4ns Isolation: -37dB@1.65Gbps ESD: Data bits @ 8kV HBM, select bit @ 2kV HBM Near-Zero Prop Delay: 200ps max. Low bit-to-bit skew Hot insertion capable Enable/Disable Time: 9ns Bidirectional Packaging (Pb-free & Green): - 42-pin TQFN (ZH42) - 48-pin BQSOP (B48) Description Pericom Semiconductor’s PI3HDMI series of switch circuits are targeted for high-resolution video networks that are based on DVI/HDMI standards, and TMDS signal processing. The PI3HDMI412FT is an 8- to 4-Channel Mux/DeMux Switch. The device multiplexes differential signals to one of two corresponding outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew and high channel-to-channel noise isolation. The maximum DVI/HDMI data rate of 1.65Gbps provides the resolution required by the next generation HDTV and PC graphics. Three differential channels are used for data (video signals for DVI or audio/video signals for HDMI), and one differential channel is used for Clock for decoding the TMDS signals at the outputs. Because of its passive bidirectional feature, this switch can be used either at the video drivers side or at the receiver side. For PC graphics applications, the device sits at the drivers side to switch between multiple display units such as PC LCD monitor, projector, TV, etc. For consumer video applications, the device sits at the receiver end to switch between the source components such as DVD, D-VHS, STB, etc. Block Diagram � �� Pin Description 42-pin TQFN �� 48-pin BQSOP �� VSS VDD VSS VDD VSS D0+ D0VSS D1+ D1VSS VDD SEL VSS D2+ D2VSS D3+ D3VSS VDD VSS VDD VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 VDD VSS D0+A D0-A D1+A D1-A VSS D2+A D2-A D3+A D3-A VSS VDD D0+B D0-B D1+B D1-B VSS D2+B D2-B D3+B D3-B VSS VDD 06-0200 1 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out Pin Description Pin # (BQSOP) 2, 4, 12, 21, 23, 25, 36, 48 1, 3, 5, 8, 11, 14, 17, 20, 22, 24, 26, 31, 37, 42, 47 13 6, 7, 9, 10, 15, 16, 18, 19, 2730, 32-35, 38-41, 43-46 Pin # (TQFN) 2, 8, 16, 18, 20, 30, 40, 42 1, 5, 10, 13, 17, 19, 21, 39, 41 9 3, 4, 6, 7, 11, 12, 14, 15, 22-29, 31-38, Pin Name(1,2) VDD VSS SEL Dx+/-n Description + Power supply 3.30 - Power supply Select pin, see truth table Data + Clk bits for TMDS signal Notes: 1. x = 0,1,2,3 2. n = A or B Truth Table(1) Function Dx to DxA Dx to DxB Notes: 1. x = 0,1,2,3 Maximum Ratings SEL L H (Above which useful life may be impaired. For user guidelines, not tested.) Storage Temperature...........................................................–65°C to +150°C Supply Voltage to VSS Potential............................................–0.5V to +2.5V DC Input Voltage ........................................................................VSS to VDD DC Output Current.............................................................................120mA Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Power Supply Characteristics Paramenter VDD VSS Description Positive Power Supply Negative Power Supply Min. 3.0 1.5 Max. 3.6 1.6 Units V V DC Electrical Characteristics for Switching over Operating Range (TA = –40°C to +85°C) Paramenter VIH VIK IIH IIL (3) Description Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Test Conditions (1) Min. 0.65(VDD-VSS)+VSS –0.5+VSS Typ.(2) Max. 0.35(VDD-VSS)+VSS Units V Guaranteed HIGH level Guaranteed LOW level VDD=Max., VIN=VDD VDD=Max., VIN=VSS VIL(3) Clamp Diode Voltage VDD=Max., IIN=–18mA –0.7+VSS –1.2+VSS ±5 ±5 µA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25°C ambient and maximum loading. 3. VIH & VIL are for SEL input only. 06-0200 2 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out Power Supply Characteristics Parameters IDD Description Quiescent Power Supply Current Test Conditions(1) VDD = Max., VIN = VDD or VSS Min. Typ.(2) 200 Max. Units µA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25°C ambient and maximum loading. Dynamic Electrical Characteristics Over the Operating Range (TA= -40º to +85ºC) Parameter XTALK Description Crosstalk Test Conditions See Fig. 1 for Measurement Setup, @ 1.65 Gbps See Fig. 2 for Measurement Setup, @ 1.65 Gbps Min. Typ. -36 dB -35 1.5 GHz Max. Units OIRR BW OFF Isolation -3db Bandwidth �� Fig 1. Crosstalk Setup 06-0200 3 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out �� Fig 2. Off-isolation setup Fig 3. Crosstalk 06-0200 4 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out Fig 4. Off Isolation Switching Characteristics (TA= -40º to +85ºC, VSS=0V, VDD=1.8V ±10%) Paramenter tPZH, tPZL tPHZ, tPLZ Description Line Enable Time - SEL to Dx+/-A, Dx+/-B (1) Line Disable Time - SEL to Dx+/-A, Dx+/-B (1) Min. 0.5 0.5 Max. 8.0 4.0 Units ns Notes: 1. For measurement setup, please see “Test Circuit For Electrical Characteristic” on page 6, and “Switching waveforms” on page 7 06-0200 5 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out Test Circuit for Electrical Characteristics �� Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. 4. All input impulses are supplied by generators having the following characteristics: PRR ≤ MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns. 5. The outputs are measured one at a time with one transition per measurement. Switch Positions Test tPLZ, tPZL (output on B-side) tPHZ, tPZH (output on B-side) Prop Delay Switch 2 x (VDD - VSS) VSS Open Test Circuit for Dynamic Electrical Characteristics �� 06-0200 6 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out Switching Waveforms �� Voltage Waveforms Enable and Disable Times Application Information 3.3V PI3HDMI412FT 1.8k-ohm 3.3V Select Line 1.5k-ohm 0V to 3.3V Select Line Control 1.5V Example of a circuit that needs to be connected to the SEL pin 06-0200 7 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out Eye Diagram Measurements TP3(Rx) Test Setup 06-0200 8 PS8798A 08/08/06 PI3HDMI412FT 4-Differential Channel