(MUR1620CT - MUR1660CT) ULTRAFAST RECTIFIERS 8 AMPERES

www.DataSheet4U.com SEMICONDUCTOR TECHNICAL DATA MOTOROLA Order this document by MUR1620CT/D SWITCHMODE • • • • • • • • ™ Power Rectifiers . . . designed for use in switching power supplies, inverters and as free wheeling diodes, these state–of–the–art devices have the following features: Ultrafast 35 and 60 Nanosecond Recovery Times 175°C Operating Junction Temperature Popular TO–220 Package Epoxy Meets UL94, VO @ 1/8″ High Temperature Glass Passivated Junction High Voltage Capability to 600 Volts Low Leakage Specified @ 150°C Case Temperature Current Derating @ Both Case and Ambient Temperatures MUR1620CT MUR1640CT MUR1660CT Motorola Preferred Devices ULTRAFAST RECTIFIERS 8 AMPERES 200–400–600 VOLTS Mechanical Characteristics: • Case: Epoxy, Molded • Weight: 1.9 grams (approximately) • Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable • Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds • Shipped 50 units per plastic tube • Marking: U1620, U1640, U1660 1 2, 4 3 4 1 2 3 CASE 221A–06 TO–220AB MAXIMUM RATINGS MUR R i Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current Total Device, (Rated VR), TC = 150°C Peak Rectified Forward Current (Rated VR, Square Wave, 20 kHz), TC = 150°C Per Leg Total Device Per Diode Leg S b l Symbol VRRM VRWM VR IF(AV) IFM IFSM TJ, Tstg 1620CT 200 1640CT 400 1660CT 600 U i Unit Volts 8.0 16 16 100 Amps Amps Amps °C Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) Operating Junction Temperature and Storage Temperature * 65 to +175 3.0 2.0 THERMAL CHARACTERISTICS, PER DIODE LEG Maximum Thermal Resistance, Junction to Case RθJC °C/W ELECTRICAL CHARACTERISTICS, PER DIODE LEG Maximum Instantaneous Forward Voltage (1) (iF = 8.0 Amps, TC = 150°C) (iF = 8.0 Amps, TC = 25°C) Maximum Instantaneous Reverse Current (1) (Rated dc Voltage, TC = 150°C) (Rated dc Voltage, TC = 25°C) Maximum Reverse Recovery Time (IF = 1.0 Amp, di/dt = 50 Amps/µs) (IF = 0.5 Amp, IR = 1.0 Amp, IREC = 0.25 Amp) (1) Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤ 2.0% vF 0.895 0.975 iR 250 5.0 trr 35 25 60 50 500 10 ns 1.00 1.30 1.20 1.50 µA Volts SWITCHMODE is a trademark of Motorola, Inc. Preferred devices are Motorola recommended choices for future use and best overall value. Rev 2 ©RectifierInc. 1996 Data Motorola, Device 1 MUR1620CT MUR1640CT MUR1660CT 100 IR, REVERSE CURRENT (m A) 70 50 800 400 200 80 40 20 8.0 4.0 2.0 0.8 0.4 0.2 0.08 0.04 0.02 0 20 40 60 TJ = 175°C 30 20 i F , INSTANTANEOUS FORWARD CURRENT (AMPS) TJ = 175°C 10 7.0 25°C 5.0 100°C 100°C 25°C 80 100 120 140 160 180 200 VR, REVERSE VOLTAGE (VOLTS) Figure 2. Typical Reverse Current, Per Leg* 3.0 2.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. IF(AV) , AVERAGE POWER DISSIPATION (WATTS) 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 140 145 150 155 160 165 170 175 180 TC, CASE TEMPERATURE (°C) SQUARE WAVE dc RATED VR APPLIED 1.0 0.7 0.5 0.3 0.2 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 vF, INSTANTANEOUS VOLTAGE (VOLTS) Figure 1. Typical Forward Voltage, Per Leg Figure 3. Current Derating, Case, Per Leg IF(AV) , AVERAGE FORWARD CURRENT (AMPS) 14 12 dc 10 8.0 SQUARE WAVE 6.0 4.0 2.0 0 0 20 40 60 80 100 120 140 160 180 200 TA, AMBIENT TEMPERATURE (°C) dc SQUARE WAVE Rq JA = 16°C/W Rq JA = 60°C/W (NO HEATSINK) PF(AV) , AVERAGE POWER DISSIPATION (WATTS) 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10 IF(AV), AVERAGE FORWARD CURRENT (AMPS) TJ = 175°C SQUARE WAVE dc Figure 4. Current Derating, Ambient, Per Leg Figure 5. Power Dissipation, Per Leg 2 Rectifier Device Data MUR1620CT MUR1640CT MUR1660CT 100 IR, REVERSE CURRENT (m A) 70 50 800 400 200 80 40 20 8.0 4.0 2.0 0.8 0.4 0.2 0.08 0.04 0.02 0 50 100 150 TJ = 175°C 150°C 100°C 30 i F , INSTANTANEOUS FORWARD CURRENT (AMPS) 20 TJ = 175°C 100°C 25°C 10 7.0 5.0 25°C 200 250 300 350 400 450 500 VR, REVERSE VOLTAGE (VOLTS) Figure 7. Typical Reverse Current, Per Leg* 3.0 2.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these curves if VR is sufficiently below rated VR. IF(AV) , AVERAGE POWER DISSIPATION (WATTS) 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 140 145 150 155 160 165 170 175 180 TC, CASE TEMPERATURE (°C) SQUARE WAVE dc RATED VR APPLIED 1.0 0.7 0.5 0.3 0.2 0.1 0.4 0.6 0.8 1.0 1.2 1.4 1.6 vF, INSTANTANEOUS VOLTAGE (VOLTS) Figure 6. Typical Forward Voltage, Per Leg Figure 8. Current Derating, Case, Per Leg IF(AV) , AVERAGE FORWARD CURRENT (AMPS) 14 12 10 dc 8.0 6.0 4.0 2.0 0 0 20 40 60 80 100 120 140 160 180 200 TA, AMBIENT TEMPERATURE (°C) SQUARE WAVE dc SQUARE WAVE Rq JA = 16°C/W Rq JA = 60°C/W (NO HEAT SINK) PF(AV) , AVERAGE POWER DISSIPATION (WATTS) 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10 IF(AV), AVERAGE FORWARD CURRENT (AMPS) TJ = 175°C SQUARE WAVE dc Figure 9. Current Derating, Ambient, Per Leg Figure 10. Power Dissipation, Per Leg Rectifier Device Data 3 MUR1620CT MUR1640CT MUR1660CT 100 IR, REVERSE CURRENT (m A) 70 50 800 400 200 80 40 20 8.0 4.0 2.0 0.8 0.4 0.2 0.08 0.04 0.02 100 200 TJ = 150°C 100°C 30 TJ = 150°C i F , INSTANTANEOUS FORWARD CURRENT (AMPS) 20 100°C 10 7.0 5.0 25°C 25°C 300 400 500 600 VR, REVERSE VOLTAGE (VOLTS) Figure 12. Typical Reverse Current, Per Leg* 3.0 2.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. IF(AV) , AVERAGE POWER DISSIPATION (WATTS) 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 140 145 150 155 160 165 170 175 180 TC, CASE TEMPERATURE (°C) SQUARE WAVE dc RATED VR APPLIED 1.0 0.7 0.5 0.3 0.2 0.1 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 vF, INSTANTANEOUS VOLTAGE (VOLTS) Figure 11. Typical Forward Voltage, Per Leg Figure 13. Current Derating, Case, Per Leg IF(AV) , AVERAGE FORWARD CURRENT (AMPS) 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 0 20 40 60 80 100 120 140 160 180 200 TA, AMBIENT TEMPERATURE (°C) dc SQUARE WAVE SQUARE WAVE dc Rq JA = 16°C/W Rq JA = 60°C/W (NO HEAT SINK) PF(AV) , AVERAGE POWER DISSIPATION (WATTS) 14 13 12 11 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 0 TJ = 175°C SQUARE WAVE dc 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10 IF(AV), AVERAGE FORWARD CURRENT (AMPS) Figure 14. Current Derating, Ambient, Per Leg Figure 15. Power Dissipation, Per Leg 4 Rectifier Device Data r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) MUR1620CT MUR1640CT MUR1660CT 1.0 D = 0.5 0.5 0.2 0.1 0.1 0.05 0.05 P(pk) 0.01 SINGLE PULSE 0.01 0.02 0.05 0.1 0.2 0.5 1.0 2.0 t1 t2 DUTY CYCLE, D = t1/t2 5.0 10 20 ZθJC(t) = r(t) RθJC D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT T1 TJ(pk) – TC = P(pk) ZθJC(t) 50 100 200 500 1000 0.02 0.01 t, TIME (ms) Figure 16. Thermal Response 1000 MUR1620CT THRU 1660CT MUR1605CT THRU 1615CT C, CAPACITANCE (pF) 300 TJ = 25°C 100 30 10 1.0 10 VR, REVERSE VOLTAGE (VOLTS) 100 Figure 17. Typical Capacitance, Per Leg Rectifier Device Data 5 MUR1620CT MUR1640CT MUR1660CT PACKAGE DIMENSIONS –T– B 4 SEATING PLANE F T S C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. DIM A B C D F G H J K L N Q R S T U V Z INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 ––– ––– 0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 ––– ––– 2.04 Q 1 2 3 A U K H Z L V G D N R J CASE 221A–06 (TO–220AB) ISSUE Y Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleg