(MG Series) Capacitors

Aluminum Electrolytic Capacitors MG series 1 Lower impedance at high frequency range. 1 Smaller case size and high ripple current. 1 1 MG SPECIFICATIONS Items Capacitance Tolerance Operating Temperature Range Rated Voltage Range Leakage Current I Characteristics 20% (120Hz, 20BC) -40 ~ +105BC 6.3 ~ 35V 0.01CV (After 2 minutes application of DC working voltage, at 20BC) Measurement Frequency: 120Hz. Temperature: 20BC Dissipation Factor (tan d) Rated Voltage (V) tan d (Max) 6.3 10 16 25 35 0.11 0.21 0.18 0.15 0.13 When nominal capacitance exceeds 1000mF, add 0.02 to the value above for each 1000mF increase. (20BC 120Hz) Measurement Frequency: 120Hz, Temperature: 20BC. Rated Voltage (V) 6.3 2 3 Within 10 2 3 25% of Initial Value 16 2 3 25 2 3 6.3 mm, 5,000hrs) www.DataSheet4U.com Low Temperature Stability Impedance Ratio (Max) ( ) 35 2 3 Z (-25BC) / Z (20BC) Z (-40BC) / Z (20BC) Capacitance Change 6,000hours, with application of working voltage at 105BC ( fD Load Life tan d Leakage Current 200% or less of Initial Specified Value Initial Specified Value or less 1,000hours, no voltage applied, at 105BC After Test UR to be applied for 30 minutes, 24 to 48hours before measurement. Shelf Life Capacitance Change tan d Leakage Current Standards Within 20% of Initial Value 200% or less of Initial Specified Value Initial Specified Value or less JIS C 5141 and JIS C 5102 PERMISSIBLE RIPPLE CURRENT Temperature Coefficient TEMP (BC) Coefficient 65 2.10 75 1.90 85 1.70 Frequency (Hz) 120 47 ~ 150 220 ~ 560 680 ~ 1800 2200 ~ 3900 4700 ~ 8200 0.40 0.50 0.60 0.75 0.85 1K 0.75 0.85 0.87 0.90 0.95 10K 0.90 0.94 0.95 0.95 0.98 100K 1.00 1.00 1.00 1.00 1.00 95 1.50 105 1.00 Frequency Coefficient Capacitance ( mF ) 59 Aluminum Electrolytic Capacitors MG series DIMENSIONS (mm) Safety Vent ( f8 up) Sleeve Rubber end seal fd 0.05 Tinned copper-ply wire D 0.5 P 0.5 L+a Max 15 min. 5 min. www.DataSheet4U.com MG fD P fd 5 2.0 0.5 Cap ( mF ) W V(V) Item 100 150 220 330 470 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 Cap ( mF ) W V(V) DxL 5 x 11 6.3 x 11 8 x 12 8 x 12 8 x 12 8 x 12 8 x 15 10 x 13 8 x 20 10 x 16 10 x 20 10 x 25 13 x 21 13 x 21 13 x 25 13 x 30 16 x 21 13 x 36 16 x 26 DxL 5 x 11 6.3 x 11 6.3 x 11 8 x 12 8 x 12 10 x 13 10 x 13 8 x 16 8 x 21 10 x 16 10 x 20 10 x 25 13 x 21 13 x 21 13 x 25 13 x 30 13 x 36 16 x 21 16 x 26 Item 47 68 100 150 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 6.3 2.5 0.5 8 3.5 0.5 10 5.0 0.6 13(12.5) 5.0 0.6 16 7.5 0.8 (L (L 16) 1.0 16) 2.0 STANDARD RATINGS 6.3 IMP 20BC -10BC R.C. DxL (mm); R.C.: (mA rms) at 105BC, 100KHz; IMP: (W max) at 20BC, 100KHz. DxL 5 x 11 6.3 x 11 6.3 x 11 8 x 12 8 x 12 10 x 13 10 x 13 8 x 16 10 x 16 10 x 16 8 x 20 10 x 20 10 x 25 13 x 21 13 x 21 13 x 25 13 x 30 16 x 21 13 x 36 16 x 26 10 IMP 20BC 0.230 0.100 0.100 0.059 0.059 0.043 0.043 0.046 0.030 0.030 0.031 0.019 0.017 0.016 0.016 0.014 0.012 0.014 0.011 0.012 -10BC 0.760 0.330 0.330 0.181 0.181 0.133 0.133 0.143 0.095 0.095 0.105 0.057 0.051 0.041 0.041 0.036 0.031 0.036 0.029 0.033 R.C. 360 450 550 820 990 1250 1360 1330 1650 1815 1550 2160 2475 2450 2725 3190 3795 3575 3925 3990 DxL 5 x 11 6.3 x 11 6.3 x 11 8 x 12 8 x 12 10 x 13 8 x 16 10 x 16 10 x 16 8 x 20 10 x 20 10 x 20 10 x 25 13 x 21 13 x 25 13 x 30 16 x 21 13 x 36 16 x 26 16 IMP 20BC 0.230 0.100 0.100 0.059 0.059 0.043 0.046 0.030 0.030 0.031 0.019 0.019 0.017 0.016 0.014 0.012 0.014 0.011 0.012 -10BC 0.760 0.330 0.330 0.181 0.181 0.133 0.143 0.095 0.095 0.105 0.057 0.057 0.051 0.041 0.036 0.031 0.036 0.029 0.033 R.C. 360 450 550 830 990 1360 1330 1650 1815 1550 1930 2160 2475 2725 3190 3795 3575 3925 3990 0.230 0.100 0.100 0.059 0.059 0.043 0.043 0.046 0.031 0.030 0.019 0.017 0.016 0.016 0.014 0.012 0.011 0.014 0.012 0.760 0.330 0.330 0.181 0.181 0.133 0.133 0.143 0.105 0.095 0.057 0.051 0.041 0.041 0.036 0.031 0.029 0.036 0.033 360 460 550 900 990 1250 1360 1300 1550 1815 2160 2475 2500 2725 3190 3795 3925 3575 3990 25 IMP 20BC 0.230 0.100 0.100 0.059 0.059 0.059 0.046 0.043 0.031 0.030 0.019 0.017 0.016 0.016 0.014 0.012 0.014 0.011 0.012 -10BC 0.760 0.330 0.330 0.181 0.181 0.181 0.143 0.133 0.105 0.095 0.057 0.051 0.041 0.041 0.036 0.031 0.036 0.029 0.033 R.C. 360 450 550 810 900 990 1330 1360 1550 1815 2160 2475 2180 2725 3190 3795 3575 3925 3990 DxL 5 x 11 6.3 x 11 6.3 x 11 8 x 12 8 x 12 8 x 16 10 x 13 8 x 20 10 x 16 10 x 20 10 x 25 13 x 21 13 x 21 13 x 25 13 x 32 16 x 21 13 x 36 16 x 26 35 IMP 20BC 0.230 0.100 0.100 0.059 0.059 0.046 0.043 0.031 0.030 0.019 0.017 0.016 0.016 0.014 0.012 0.014 0.011 0.012 -10BC 0.760 0.330 0.330 0.181 0.181 0.143 0.133 0.105 0.095 0.057 0.051 0.041 0.041 0.041 0.031 0.036 0.029 0.033 R.C. 360 450 550 820 990 1330 1360 1550 1815 2160 2475 2725 2920 3190 3795 3575 3925 3990 13mm may be replaced by 12.5mm upon customer's request. 60