SWITCHMODE Power Rectifier

www.DataSheet4U.com MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 SWITCHMODEt Power Rectifier 100 V, 40 A Features and Benefits http://onsemi.com 1 2, 4 3 4 • • • • • • • Low Forward Voltage: 0.67 V @ 125°C Low Power Loss/High Efficiency High Surge Capacity 175°C Operating Junction Temperature 40 A Total (20 A Per Diode Leg) Guard−Ring for Stress Protection Pb−Free Packages are Available 1 2 3 MARKING DIAGRAMS TO−220AB CASE 221A PLASTIC STYLE 6 Applications AYWW B41H100G AKA • Power Supply − Output Rectification • Power Management • Instrumentation Mechanical Characteristics: 4 • Case: Epoxy, Molded • Epoxy Meets UL 94 V−0 @ 0.125 in • Weight (Approximately): 1.9 Grams (TO−220AB) D2PAK CASE 418B STYLE 3 1 3 AYWW B41H100G AKA 1.7 Grams (D2PAK) 1.5 Grams (TO−262) • Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable • Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds MAXIMUM RATINGS Please See the Table on the Following Page 12 3 4 I2PAK (TO−262) CASE 418D PLASTIC STYLE 3 A Y WW G AKA AYWW B41H100G AKA = Assembly Location = Year = Work Week = Pb−Free Package = Polarity Designator ORDERING INFORMATION Device MBR41H100CT MBR41H100CTG MBRB41H100CT−1G MBRB41H100CTT4G Package TO−220 TO−220 (Pb−Free) TO−262 (Pb−Free) D2PAK (Pb−Free) Shipping † 50 Units/Rail 50 Units/Rail 50 Units/Rail 800/Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2007 1 March, 2007 − Rev. 4 Publication Order Number: MBR41H100CT/D MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 MAXIMUM RATINGS (Per Diode Leg) Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current (Rated VR) TC = 150°C Peak Repetitive Forward Current (Rated VR, Square Wave, 20 kHz) TC = 145°C Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) Operating Junction Temperature (Note 1) Storage Temperature Voltage Rate of Change (Rated VR) Controlled Avalanche Energy (see test conditions in Figures 10 and 11) ESD Ratings: Machine Model = C Human Body Model = 3B Symbol VRRM VRWM VR IF(AV) IFRM IFSM TJ Tstg dv/dt WAVAL Value 100 Unit V 20 40 350 +175 *65 to +175 10,000 400 > 400 > 8000 A A A °C °C V/ms mJ V THERMAL CHARACTERISTICS (PER DIODE LEG) Maximum Thermal Resistance − Junction−to−Case − Junction−to−Ambient RqJC RqJA 2.0 70 °C/W ELECTRICAL CHARACTERISTICS (Per Diode Leg) Maximum Instantaneous Forward Voltage (Note 2) (IF = 20 A, TC = 25°C) (IF = 20 A, TC = 125°C) (IF = 40 A, TC = 25°C) (IF = 40 A, TC = 125°C) Maximum Instantaneous Reverse Current (Note 2) (Rated DC Voltage, TC = 125°C) (Rated DC Voltage, TC = 25°C) vF 0.80 0.67 0.90 0.76 iR 10 0.01 mA V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The heat generated must be less than the thermal conductivity from Junction−to−Ambient: dPD/dTJ < 1/RqJA. 2. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%. http://onsemi.com 2 MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 IF, INSTANTANEOUS FORWARD CURRENT (AMPS) IF, INSTANTANEOUS FORWARD CURRENT (AMPS) 1000 1000 100 TJ = 150°C 10 TJ = 125°C TJ = 25°C 100 TJ = 125°C 10 TJ = 150°C 1 TJ = 25°C 1 0.1 0 0.2 0.4 0.6 0.8 1.0 1.2 VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.1 0 0.2 0.4 0.6 0.8 1.0 1.2 VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) Figure 1. Typical Forward Voltage Figure 2. Maximum Forward Voltage 1.0E−01 IR, REVERSE CURRENT (AMPS) 1.0E−02 1.0E−03 TJ = 125°C TJ = 150°C IR, MAXIMUM REVERSE CURRENT (AMPS) 1.0E−01 TJ = 150°C 1.0E−02 1.0E−03 TJ = 125°C 1.0E−04 1.0E−05 1.0E−06 TJ = 25°C 1.0E−04 1.0E−05 1.0E−06 TJ = 25°C 1.0E−07 1.0E−07 1.0E−08 0 1.0E−08 0 20 40 60 80 100 20 40 60 80 100 VR, REVERSE VOLTAGE (VOLTS) VR, REVERSE VOLTAGE (VOLTS) Figure 3. Typical Reverse Current Figure 4. Maximum Reverse Current IF, AVERAGE FORWARD CURRENT (AMPS) PFO, AVERAGE POWER DISSIPATION (WATTS) 35 30 25 20 15 10 5 0 100 SQUARE WAVE dc 50 45 40 35 30 25 20 15 10 5 0 0 5 10 15 20 25 30 35 40 45 50 IO, AVERAGE FORWARD CURRENT (AMPS) DC SQUARE 110 120 130 140 150 160 170 180 TC, CASE TEMPERATURE (°C) Figure 5. Current Derating Figure 6. Forward Power Dissipation http://onsemi.com 3 MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 10000 TJ = 25°C C, CAPACITANCE (pF) 1000 100 10 0 20 40 60 80 100 VR, REVERSE VOLTAGE (VOLTS) Figure 7. Capacitance R(t), TRANSIENT THERMAL RESISTANCE 100 D = 0.5 0.2 0.1 0.05 10 1 0.01 0.1 P(pk) t1 0.01 SINGLE PULSE t2 DUTY CYCLE, D = t1/t2 0.0001 0.001 0.01 t1, TIME (sec) 0.1 1 10 100 1000 0.001 0.000001 0.00001 Figure 8. Thermal Response Junction−to−Ambient R(t), TRANSIENT THERMAL RESISTANCE 10 1 D = 0.5 0.2 0.1 0.05 0.01 P(pk) t1 t2 0.1 0.01 SINGLE PULSE DUTY CYCLE, D = t1/t2 0.001 0.000001 0.00001 0.0001 0.001 0.01 t1, TIME (sec) 0.1 1 10 100 1000 Figure 9. Thermal Response Junction−to−Case http://onsemi.com 4 MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 +VDD IL 10 mH COIL VD MERCURY SWITCH ID IL ID VDD t0 t1 t2 t BVDUT S1 DUT Figure 10. Test Circuit Figure 11. Current−Voltage Waveforms The unclamped inductive switching circuit shown in Figure 10 was used to demonstrate the controlled avalanche capability of this device. A mercury switch was used instead of an electronic switch to simulate a noisy environment when the switch was being opened. When S1 is closed at t0 the current in the inductor IL ramps up linearly; and energy is stored in the coil. At t1 the switch is opened and the voltage across the diode under test begins to rise rapidly, due to di/dt effects, when this induced voltage reaches the breakdown voltage of the diode, it is clamped at BVDUT and the diode begins to conduct the full load current which now starts to decay linearly through the diode, and goes to zero at t2. By solving the loop equation at the point in time when S1 is opened; and calculating the energy that is transferred to the diode it can be shown that the total energy transferred is equal to the energy stored in the inductor plus a finite amount of energy from the VDD power supply while the diode is in breakdown (from t1 to t2) minus any losses due to finite component resistances. Assuming the component resistive elements are small Equation (1) approximates the total energy transferred to the diode. It can be seen from this equation that if the VDD voltage is low compared to the breakdown voltage of the device, the amount of energy contributed by the supply during breakdown is small and the total energy can be assumed to be nearly equal to the energy stored in the coil during the time when S1 was closed, Equation (2). EQUATION (1): BV 2 DUT W [ 1 LI LPK AVAL 2 BV –V DUT DD EQUATION (2): 2 W [ 1 LI LPK AVAL 2 http://onsemi.com 5 MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 PACKAGE DIMENSIONS TO−220 PLASTIC CASE 221A−09 ISSUE AD −T− B 4 SEATING PLANE F T S C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. DIM A B C D F G H J K L N Q R S T U V Z INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 −−− −−− 0.080 ANODE CATHODE ANODE CATHODE MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 −−− −−− 2.04 Q 123 A U K H Z L V G D N R J STYLE 6: PIN 1. 2. 3. 4. http://onsemi.com 6 MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 PACKAGE DIMENSIONS D2PAK 3 CASE 418B−04 ISSUE J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 418B−01 THRU 418B−03 OBSOLETE, NEW STANDARD 418B−04. DIM A B C D E F G H J K L M N P R S V INCHES MIN MAX 0.340 0.380 0.380 0.405 0.160 0.190 0.020 0.035 0.045 0.055 0.310 0.350 0.100 BSC 0.080 0.110 0.018 0.025 0.090 0.110 0.052 0.072 0.280 0.320 0.197 REF 0.079 REF 0.039 REF 0.575 0.625 0.045 0.055 MILLIMETERS MIN MAX 8.64 9.65 9.65 10.29 4.06 4.83 0.51 0.89 1.14 1.40 7.87 8.89 2.54 BSC 2.03 2.79 0.46 0.64 2.29 2.79 1.32 1.83 7.11 8.13 5.00 REF 2.00 REF 0.99 REF 14.60 15.88 1.14 1.40 C E −B− 4 V W A 1 2 3 S −T− SEATING PLANE K G D 3 PL 0.13 (0.005) H M W J TB M VARIABLE CONFIGURATION ZONE L M R N U L P L M STYLE 3: PIN 1. ANODE 2. CATHODE 3. ANODE 4. CATHODE M F VIEW W−W 1 F VIEW W−W 2 F VIEW W−W 3 SOLDERING FOOTPRINT* 8.38 0.33 10.66 0.42 1.016 0.04 5.08 0.20 3.05 0.12 17.02 0.67 SCALE 3:1 mm inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 7 MBR41H100CT, MBRB41H100CT, MBRB41H100CT−1 PACKAGE DIMENSIONS I2PAK (TO−262) CASE 418D−01 ISSUE C C −B− 4 E V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G H J K S V W INCHES MIN MAX 0.335 0.380 0.380 0.406 0.160 0.185 0.026 0.035 0.045 0.055 0.122 REF 0.100 BSC 0.094 0.110 0.013 0.025 0.500 0.562 0.390 REF 0.045 0.070 0.522 0.551 ANODE CATHODE ANODE CATHODE MILLIMETERS MIN MAX 8.51 9.65 9.65 10.31 4.06 4.70 0.66 0.89 1.