HEXFET Power MOSFET

SMPS MOSFET PD - 94986 IRFBC40APbF HEXFET® Power MOSFET Applications l Switch Mode Power Supply ( SMPS ) l Uninterruptable Power Supply l High speed power switching l Lead-Free Benefits l Low Gate Charge Qg results in Simple Drive Requirement l Improved Gate, Avalanche and Dynamic dv/dt Ruggedness l Fully Characterized Capacitance and Avalanche Voltage and Current l Effective Coss Specified ( See AN 1001) VDSS 600V Rds(on) max 1.2Ω ID 6.2A TO-220AB G DS Absolute Maximum Ratings Parameter ID @ TC = 25°C ID @ TC = 100°C IDM PD @TC = 25°C VGS dv/dt TJ TSTG Continuous Drain Current, VGS @ 10V Continuous Drain Current, VGS @ 10V Pulsed Drain Current  Power Dissipation Linear Derating Factor Gate-to-Source Voltage Peak Diode Recovery dv/dt ƒ Operating Junction and Storage Temperature Range Soldering Temperature, for 10 seconds Mounting torqe, 6-32 or M3 screw Max. 6.2 3.9 25 125 1.0 ± 30 6.0 -55 to + 150 300 (1.6mm from case ) 10 lbf•in (1.1N•m) Units A W W/°C V V/ns °C Typical SMPS Topologies: l Single Transistor Forward Notes  through … are on page 8 www.irf.com 1 2/5/04 IRFBC40APbF V(BR)DSS Static @ TJ = 25°C (unless otherwise specified) Parameter Min. Drain-to-Source Breakdown Voltage 600 ∆V(BR)DSS/∆TJ Breakdown Voltage Temp. Coefficient ––– RDS(on) Static Drain-to-Source On-Resistance ––– VGS(th) Gate Threshold Voltage 2.0 ––– IDSS Drain-to-Source Leakage Current ––– Gate-to-Source Forward Leakage ––– IGSS Gate-to-Source Reverse Leakage ––– Typ. ––– 0.66 ––– ––– ––– ––– ––– ––– Max. Units Conditions ––– V VGS = 0V, ID = 250µA ––– V/°C Reference to 25°C, ID = 1mA† 1.2 Ω VGS = 10V, ID = 3.7A „ 4.0 V VDS = VGS, ID = 250µA 25 VDS = 600V, VGS = 0V µA 250 VDS = 480V, VGS = 0V, TJ = 125°C 100 VGS = 30V nA -100 VGS = -30V Dynamic @ TJ = 25°C (unless otherwise specified) gfs Qg Q gs Qgd td(on) tr td(off) tf Ciss Coss Crss Coss Coss Coss eff. Parameter Forward Transconductance Total Gate Charge Gate-to-Source Charge Gate-to-Drain ("Miller") Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Input Capacitance Output Capacitance Reverse Transfer Capacitance Output Capacitance Output Capacitance Effective Output Capacitance Min. 3.4 ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– Typ. ––– ––– ––– ––– 13 23 31 18 1036 136 7.0 1487 36 48 Max. Units Conditions ––– S VDS = 50V, ID = 3.7A 42 ID = 6.2A 10 nC VDS = 480V 20 VGS = 10V, See Fig. 6 and 13 „ ––– VDD = 300V ––– ID = 6.2A ns ––– RG = 9.1Ω ––– RD = 47Ω,See Fig. 10 „ ––– VGS = 0V ––– VDS = 25V ––– pF ƒ = 1.0MHz, See Fig. 5 ––– VGS = 0V, VDS = 1.0V, ƒ = 1.0MHz ––– VGS = 0V, VDS = 480V, ƒ = 1.0MHz ––– VGS = 0V, VDS = 0V to 480V … Avalanche Characteristics Parameter EAS IAR EAR Single Pulse Avalanche Energy‚ Avalanche Current Repetitive Avalanche Energy Typ. ––– ––– ––– Max. 570 6.2 13 Units mJ A mJ Thermal Resistance Parameter RθJC RθCS RθJA Junction-to-Case Case-to-Sink, Flat, Greased Surface Junction-to-Ambient Typ. ––– 0.50 Max. 1.0 ––– 62 Units °C/W Diode Characteristics IS I SM VSD t rr Q rr ton Parameter Continuous Source Current (Body Diode) Pulsed Source Current (Body Diode)  Diode Forward Voltage Reverse Recovery Time Reverse RecoveryCharge Forward Turn-On Time Min. Typ. Max. Units Conditions D MOSFET symbol ––– ––– 6.2 showing the A G integral reverse ––– ––– 25 S p-n junction diode. ––– ––– 1.5 V TJ = 25°C, IS = 6.2A, VGS = 0V „ ––– 431 647 ns TJ = 25°C, IF = 6.2A ––– 1.8 2.8 µC di/dt = 100A/µs „ Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD) 2 www.irf.com IRFBC40APbF 100 VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V TOP 100 I D , Drain-to-Source Current (A) 10 I D , Drain-to-Source Current (A) 10 VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V TOP 1 4.5V 0.1 4.5V 1 0.01 0.1 20µs PULSE WIDTH TJ = 25 °C J 1 10 100 0.1 20µs PULSE WIDTH TJ = 150 °C J 1 10 100 VDS , Drain-to-Source Voltage (V) VDS , Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics, Fig 2. Typical Output Characteristics, 100 3.0 RDS(on) , Drain-to-Source On Resistance (Normalized) 6.2A ID = 5.9A I D , Drain-to-Source Current (A) 2.5 TJ = 150 ° C 10 2.0 TJ = 25 ° C 1 1.5 1.0 0.5 0.1 4.0 V DS = 50V 20µs PULSE WIDTH 5.0 6.0 7.0 8.0 9.0 10.0 0.0 -60 -40 -20 VGS = 10V 0 20 40 60 80 100 120 140 160 VGS , Gate-to-Source Voltage (V) TJ , Junction Temperature ( °C) Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance Vs. Temperature www.irf.com 3 IRFBC40APbF 100000 VGS = 0V, f = 1 MHZ Ciss = C + Cgd, C gs ds SHORTED Crss = C gd Coss = C + Cgd ds 20 ID = 6.2A 5.9A VDS = 480V VDS = 300V VDS = 120V VGS , Gate-to-Source Voltage (V) 10000 C, Capacitance(pF) 16 1000 Ciss Coss 12 100 8 10 Crss 4 1 1 10 100 1000 0 FOR TEST CIRCUIT SEE FIGURE 13 0 8 16 24 32 40 VDS, Drain-to-Source Voltage (V) QG , Total Gate Charge (nC) Fig 5. Typical Capacitance Vs. Drain-to-Source Voltage Fig 6. Typical Gate Charge Vs. Gate-to-Source Voltage 100 100 ISD , Reverse Drain Current (A) OPERATION IN THIS AREA LIMITED BY RDS(on) 10us 10 TJ = 150 ° C I D , Drain Current (A) 10 100us TJ = 25 ° C 1 1ms 1 10ms 0.1 0.4 V GS = 0 V 0.6 0.8 1.0 1.2 0.1 TC = 25 °C TJ = 150 °C Single Pulse 10 100 1000 10000 VSD ,Source-to-Drain Voltage (V) VDS , Drain-to-Source Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage Fig 8. Maximum Safe Operating Area 4 www.irf.com IRFBC40APbF 7.0 6.0 V DS V GS RG 10V Pulse Width ≤ 1 µs Duty Factor ≤ 0.1 % RD D.U.T. + ID , Drain Current (A) 5.0 4.0 3.0 2.0 1.0 0.0 -V DD Fig 10a. Switching Time Test Circuit VDS 90% 25 50 75 100 125 150 TC , Case Temperature ( °C) Fig 9. Maximum Drain Current Vs. Case Temperature 10% VGS td(on) tr t d(off) tf Fig 10b. Switching Time Waveforms 10 Thermal Response (Z thJC ) 1 D = 0.50 0.20 0.1 0.10 0.05 0.02 0.01 PDM t1 t2 SINGLE PULSE (THERMAL RESPONSE) 0.0001 0.001 0.01 Notes: 1. Duty factor D = t 1 / t 2 2. Peak T J = P DM x Z thJC + TC 0.1 1 0.01 0.00001 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRFBC40APbF EAS , Single Pulse Avalanche Energy (mJ) 15V 1400 1200 1000 800 600 400 200 0 TOP BOTTOM VDS L DRIVER ID 2.8A 3.9A 6.2A RG 20V D.U.T IAS tp + V - DD A 0.01Ω Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp 25 Starting TJ , Junction Temperature ( °C) 50 75 100 125 150 I AS Fig 12b. Unclamped Inductive Waveforms QG Fig 12c. Maximum Avalanche Energy Vs. Drain Current 820 10 V QGS QGD V DSav , Avalanche Voltage ( V ) 800 VG Charge 780 Fig 13a. Basic Gate Charge Waveform Current Regulator Same Type as D.U.T. 760 50KΩ 12V .2µF .3µF 740 D.U.T. VGS 3mA + V - DS 720 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 IAV , Avalanche Current ( A) IG ID Current Sampling Resistors Fig 13b. Gate Charge Test Circuit Fig 12d. Typical Drain-to-Source Voltage Vs. Avalanche Current 6 www.irf.com IRFBC40APbF Peak Diode Recovery dv/dt Test Circuit D.U.T + ƒ + Circuit Layout Considerations • Low Stray Inductance • Ground Plane • Low Leakage Inductance Current Transformer ‚ - „ +  RG • • • • dv/dt controlled by RG Driver same type as D.U.T. ISD controlled by Duty Factor "D" D.U.T. - Device Under Test + V DD Driver Gate Drive P.W. Period D= P.W. Period VGS=10V * D.U.T. ISD Waveform Reverse Recovery Current Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt VDD Re-Applied Voltage Inductor Curent Body Diode Forward Drop Ripple ≤ 5% ISD * VGS = 5V for Logic Level Devices Fig 14. For N-Channel HEXFETS www.irf.com 7 IRFBC40APbF TO-220AB Package Outline 2.87 (.113) 2.62 (.103) 10.54 (.415) 10.29 (.405) 3.78 (.149) 3.54 (.139) -A6.47 (.255) 6.10 (.240) -B4.69 (.185) 4.20 (.165) 1.32 (.052) 1.22 (.048) 4 15.24 (.600) 14.84 (.584) 1.15 (.045) MIN 1 2 3 LEAD ASSIGNMENTS IGBTs, CoPACK 1 - GATE 21- GATE DRAIN 1- GATE 32- DRAINSOURCE 2- COLLECTOR 3- SOURCE 3- EMITTER 4 - DRAIN LEAD ASSIGNMENTS HEXFET 14.09 (.555) 13.47 (.530) 4- DRAIN 4.06 (.160) 3.55 (.140) 4- COLLECTOR 3X 3X 1.40 (.055) 1.15 (.045) 0.93 (.037) 0.69 (.027) M BAM 3X 0.55 (.022) 0.46 (.018) 0.36 (.014) 2.54 (.100) 2X NOTES: 1 DIMENSIONING & TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION : INCH 2.92 (.115) 2.64 (.104) 3 OUTLINE CONFORMS TO JEDEC OUTLINE TO-220AB. 4 HEATSINK & LEAD MEASUREMENTS DO NOT INCLUDE BURRS. TO-220AB Part Marking Information E XAMPL E : T HIS IS AN IR F 1010 L OT CODE 1789 AS S E MB L E D ON WW 19, 1997 IN T H E AS S E MB L Y L INE "C" INT E R NAT IONAL R E CT IF IE R L OGO AS S E MB L Y L OT CODE PAR T NU MB E R Note: "P" in assembly line position indicates "Lead-Free" DAT E CODE YE AR 7 = 1997 WE E K 19 L INE C Notes:  Repetitive rating; pulse width limited by ‚ Starting TJ = 25°C, L =29.6mH max. junction temperature. ( See fig. 11 ) „ Pulse width ≤ 300µs; duty cycle ≤ 2%. … Coss eff. is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 to 80% VDSS RG = 25Ω, IAS = 6.2A. (See Figure 12) TJ ≤ 150°C ƒ ISD ≤ 6.2A, di/dt ≤ 80A/µs, VDD ≤ V(BR)DSS, Data and specifications subject to change without notice. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information.02/04 8 www.irf.com