High Speed LVTTL Compatible 3.3 Volt Optocouplers

Agilent HCPL-260L/ 060L/263L/063L High Speed LVTTL Compatible 3.3 Volt Optocouplers Data Sheet Features • Low power consumption • 15 kV/µs minimum Common Mode Rejection (CMR) at VCM = 50 V • High speed: 15 MBd typical • LVTTL/LVCMOS compatible Description The HCPL-260L/060L/263L/063L are optically coupled gates that combine a GaAsP light emitting diode and an integrated high gain photo detector. An enable input allows the detector to be strobed. The output of the detector IC is an open collector Schottky-clamped transistor. The internal shield provides a guaranteed common mode transient immunity specification of 15 kV/ µs. Functional Diagram HCPL-260L/060L NC ANODE CATHODE NC 1 2 3 4 SHIELD 8 7 6 5 VCC VE VO GND ANODE 1 CATHODE 1 CATHODE 2 ANODE 2 1 2 3 4 SHIELD HCPL-263L/063L 8 7 6 5 VCC VO1 VO2 GND • Low input current capability: 5 mA This unique design provides maximum AC and DC circuit isolation while achieving LVTTL/LVCMOS compatibility. The optocoupler AC and DC operational parameters are guaranteed from –40˚C to +85˚C allowing trouble-free system performance. • Guaranteed AC and DC performance over temperature: –40˚C to +85˚C • Available in 8-pin DIP, SOIC-8 • Strobable output (single channel products only) • Safety approvals; UL, CSA, VDE (pending) Applications • Isolated line receiver • Computer-peripheral interfaces • Microprocessor system interfaces • Digital isolation for A/D, D/A conversion • Switching power supply • Instrument input/output isolation • Ground loop elimination • Pulse transformer replacement • Field buses TRUTH TABLE (POSITIVE LOGIC) LED ON OFF ON OFF ON OFF ENABLE H H L L NC NC OUTPUT L H H H L H TRUTH TABLE (POSITIVE LOGIC) LED ON OFF OUTPUT L H A 0.1 µF bypass capacitor must be connected between pins 5 and 8. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. These optocouplers are suitable for high speed logic interfacing, input/output buffering, as line receivers in environments that conventional line receivers cannot tolerate and are recommended for use in extremely high ground or induced noise environments. These optocouplers are available in an 8-pin DIP and industry standard SO-8 package. The part numbers are as follows: 8-pin DIP HCPL-260L HCPL-263L SO-8 Package HCPL-060L HCPL-063L Ordering Information Specify Part Number followed by Option Number (if desired). Example: HCPL-260L #XXX 060 = VDE 0884 VIORM = 630 Vpeak Option 500 = Tape and Reel Packaging Option Option data sheets available. Contact Agilent sales representative or authorized distributor for information. Schematic HCPL-260L/060L ICC 8 IO 6 VCC 1 IF1 HCPL-263L/063L ICC 8 IO1 7 VCC VO1 IF 2+ VO + VF1 VF – 3 SHIELD IE 5 7 VE GND – 2 SHIELD 3 – IF2 IO2 6 VO2 USE OF A 0.1 F BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5). VF2 + 4 SHIELD 5 GND Package Outline Drawings 8-Pin DIP Package 7.62 ± 0.25 (0.300 ± 0.010) 5 6.35 ± 0.25 (0.250 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) TYPE NUMBER 8 7 6 OPTION CODE* DATE CODE A XXXXZ YYWW RU 1 1.19 (0.047) MAX. 2 3 4 UL RECOGNITION 1.78 (0.070) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 5° TYP. 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 (0.043 ± 0.013) 0.65 (0.025) MAX. 2.54 ± 0.25 (0.100 ± 0.010) DIMENSIONS IN MILLIMETERS AND (INCHES). *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. Small Outline SO-8 Package 8 7 6 5 3.937 ± 0.127 (0.155 ± 0.005) PIN ONE 1 0.406 ± 0.076 (0.016 ± 0.003) 2 XXX YWW 5.994 ± 0.203 (0.236 ± 0.008) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 3 4 1.270 BSG (0.050) * 5.080 ± 0.127 (0.200 ± 0.005) 7° 0.432 (0.017) 45° X 3.175 ± 0.127 (0.125 ± 0.005) 0 ~ 7° 1.524 (0.060) 0.203 ± 0.102 (0.008 ± 0.004) 0.228 ± 0.025 (0.009 ± 0.001) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 0.305 MIN. (0.012) Solder Reflow Temperature Profile (Surface Mount Option Parts) 260 240 220 200 180 160 140 120 100 80 60 40 20 0 0 1 Regulatory Information The HCPL-260L/060L/263L/063L are pending by the following organizations: ∆T = 145°C, 1°C/SEC ∆T = 115°C, 0.3°C/SEC UL TEMPERATURE – °C Approval (pending) under UL 1577, Component Recognition Program, File E55361. ∆T = 100°C, 1.5°C/SEC CSA 2 3 4 5 6 7 8 9 10 11 12 Approval (pending) under CSA Component Acceptance Notice #5, File CA 88324. VDE TIME – MINUTES NOTE: USE OF NON-CHLORINE ACTIVATED FLUXES IS HIGHLY RECOMMENDED. Approval (pending) according to VDE 0884/06.92. Insulation and Safety Related Specifications 8-Pin DIP (300 Mil) Value 7.1 7.4 0.08 SO-8 Value 4.9 4.8 0.08 Parameter Minimum External Air Gap (External Clearance) Minimum External Tracking (External Creepage) Minimum Internal Plastic Gap (Internal Clearance) Symbol L (101) L (102) Units mm mm mm Minimum Internal Tracking (Internal Creepage) Tracking Resistance (Comparative Tracking Index) Isolation Group NA CTI 200 NA 200 mm Volts Conditions Measured from input terminals to output terminals, shortest distance through air. Measured from input terminals to output terminals, shortest distance path along body. Through insulation distance, conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Measured from input terminals to output terminals, along internal cavity. DIN IEC 112/VDE 0303 Part 1 IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) VDE 0884 Insulation Related Characteristics Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 300 V rms for rated mains voltage ≤ 450 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and Sample Test, tm = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 16, Thermal Derating curve.) Case Temperature Input Current Output Power Insulation Resistance at TS, V IO = 500 V Symbol Characteristic I-IV I-III 55/85/21 2 630 1181 Units VIORM VPR Vpeak Vpeak VPR VIOTM 945 6000 Vpeak Vpeak TS IS,INPUT PS,OUTPUT RS 175 230 600 ≥ 109 ˚C mA mW Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section (VDE 0884), for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. Absolute Maximum Ratings (No Derating Required up to 85˚C) Parameter Storage Temperature Operating Temperature† Average Forward Input Current Symbol TS TA IF Package** Min. –55 –40 Max. 125 85 20 15 5 3 40 7 VCC + 0.5 5 50 7 85 60 260˚C for 10 sec., 1.6 mm below seating plane 260˚C for 10 sec., up to seating plane See Package Outline Drawings section V mW V V mA mA V mW Units ˚C ˚C mA Note Reverse Input Voltage Input Power Dissipation Supply Voltage (1 Minute Maximum) Enable Input Voltage (Not to Exceed VCC by more than 500 mV) Enable Input Current Output Collector Current Output Collector Voltage Output Collector Power Dissipation VR PI VCC VE IE IO VO PO Single 8-Pin DIP Single SO-8 Dual 8-Pin DIP Dual SO-8 8-Pin DIP, SO-8 2 1, 3 1 Single 8-Pin DIP Single SO-8 1 1 Lead Solder Temperature (Through Hole Parts Only) TLS Single 8-Pin DIP Single SO-8 Dual 8-Pin DIP Dual SO-8 8-Pin DIP 1, 4 Solder Reflow Temperature Profile (Surface Mount Parts Only) SO-8 **Ratings apply to all devices except otherwise noted in the Package column. Recommended Operating Conditions Parameter Input Current, Low Level Input Current, High Level[1] Power Supply Voltage Low Level Enable Voltage High Level Enable Voltage Operating Temperature Fan Out (at RL = 1 kΩ )[1] Output Pull-up Resistor Symbol IFL* IFH** VCC VEL VEH TA N RL Min. 0 5 2.7 0 2.0 –40 330 Max. 250 15 3.3 0.8 VCC 85 5 4k Units µA mA V V V ˚C TTL Loads Ω *The off condition can also be guaranteed by ensuring that VFL ≤ 0.8 volts. **The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be used for best performance and to permit at least a 20% LED degradation guardband. Electrical Specifications Over Recommended Temperature (T A = –40˚C to +85˚C) unless otherwise specified. All Typicals at V CC = 3.3 V, TA = 25˚C. All enable test conditions apply to single channel products only. See Note 5. Parameter High Level Output Current Input Threshold Current Sym. IOH* ITH Min. Typ. 4.5 3.0 Max. 50 5.0 Units µA mA Test Conditions V CC = 3.3 V, V E = 2.0 V, VO = 3.3 V, IF = 250 µA VCC = 3.3 V, V E = 2.0 V, VO = 0.6 V, IOL (Sinking) = 13 mA VCC = 3.3 V, V E = 2.0 V, IF = 5 mA, IOL (Sinking) = 13 mA VE = 0.5 V VCC = 3.3 V IF = 0 mA VE = 0.5 V VCC = 3.3 V IF = 10 mA VCC = 3.3 V, V E = 2.0 V VCC = 3.3 V, V E = 0.5 V Fig. 1 2 Note 1, 15 15 Low Level Output Voltage VOL* 0.35 0.6 V 3 15 High Level Supply Current Low Level Supply Current High Level Enable Current Low Level Enable Current High Level Enable Voltage Low Level Enable Voltage Input Forward Voltage Input Reverse Breakdown Voltage Input Diode Temperature Coefficient Input Capacitance ICCH ICCL IEH IEL* VEH VEL VF BVR* ∆V F/ ∆T A CIN 4.7 7.0 –0.5 –0.5 2.0 1.4 5 1.5 7.0 10.0 –1.2 –1.2 0.8 1.75* mA mA mA mA V V V V mV˚C 15 TA = 25˚C IF = 10 mA IR = 10 µA IF = 10 mA 5 1 1 1 –1.6 –1.9 60 pF