Refl ective Photointerrupter

www.DataSheet4U.com GP2A200LCS0F Series GP2A200LCS0F Series Detecting Distance : 2 to 22mm *OPIC Output, Reflective Photointerrupter with Connector ■ Description GP2A200LCS0F Series are OPIC output, reflective photointerrupters with emitter and detector facing the same direction in a molding that provides non-contact sensing. This family of devices uses light modulation to reduce the affects of disturbing light, and the sensor is optimized to work in the selected focal distance. A 3-pin connector is included to allow remote-mount or off-board designs. ■ Agency approvals/Compliance 1. Compliant with RoHS directive ■ Applications 1. General purpose detection of paper presence or motion. 2. Example: PPC, FAX, Printer ■ Features 1. Reflective with OPIC Light Modulated Output 2. Highlights : • Includes additional screw fixing holes • Position pin to prevent mis-alignment • Long focal distance 3. Key Parameters : • Detecting distance : 2 to 22mm (White paper) 5 to 15mm (Black paper) • Undetecting distance : over 90mm (White paper) • Connector : GP2A200LCS0F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A200LCSCF ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A240LCS0F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A210LCSJF ; Tyco Electronics AMP K.K. (PN : 4-292133-3) 4. Lead free and RoHS directive compliant * "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signalprocessing Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: D3-A05101EN Date Jun. 30. 2005 © SHARP Corporation GP2A200LCS0F Series ■ Internal Connection Diagram Reflective object Voltage regulator Demodulator circuit 1 1 2 3 2 VCC VOUT GND Amp. 3 Comparator Oscillator circuit Sync. detecting circuit ■ Outline Dimensions GP2A200LCS0F 33 3.1 4.5 9 17.7 (7.8) 9.6 7 (6.8) (Unit : mm) GP2A200LCSCF 3.5 φ3.2 6.1 3.5 5.2 (5.8) 7.8 1 2 3 View A φ3. 6.2 6 12 Optical center VCC VOUT GND 9 2 Connector : 292133-3 (Tyco Electronics AMP K.K.) 6 12 3 (5.8) 1 2 3 Connector : 292133-3 (Tyco Electronics AMP. K. K) 8 4.5 5.2 VCC VOUT GND +0 φ3−0.2 (0.65) 2.5 10.2 (0.9) 7 3.5 0 • Unspecified tolerance shall be as follows ; 26.5 32 4-SR1 View A 0 2 (6.8) (7.8) • Unspecified tolerance shall be as follows ; Date code Dimensions Tolerance less than 6 ±0.2 6 or more less than 14 ±0.3 14 or more ±0.4 • *( ) : Reference dimensions Date code Dimensions Tolerance less than 6 ±0.2 6 or more less than 14 ±0.3 14 or more ±0.4 • *( ) : Reference dimensions Product mass : approx. 1.95g GP2A210LCSJF 33 3.1 4.5 9 17.7 (6.8) Product mass : approx. 2.3g GP2A240LCS0F 33 3.1 4.5 17.7 (7.8) (6.8) (7.8) 9 1 2 3 φ3.2 6.2 6 12 Optical center VCC VOUT GND 1 2 3 φ3.2 6.2 6 12 Optical center Connector : 4-292133-3 (Yellow) (Tyco Electronics AMP K.K.) 8 4.5 (5 .8) 7.8 8 4.5 Connector : 292133-3 (Tyco Electronics AMP K.K.) (0.65) (5 .8) 7.8 2.5 2.5 26.5 φ3+0.0 −0.2 1 2 3 26.5 2 1 2 3 9 9 • Unspecified tolerance shall be as follows ; 5 1 • Unspecified tolerance shall be as follows ; Date code • : Portion Built-in IR-90 filter Dimensions Tolerance less than 6 ±0.2 6 or more less than 14 ±0.3 14 or more ±0.4 • *( ) : Reference dimensions Date code Dimensions Tolerance less than 6 ±0.2 6 or more less than 14 ±0.3 14 or more ±0.4 • *( ) : Reference dimensions Product mass : approx. 1.95g Product mass : approx. 1.95g Connector terminal plating material : Sn Sheet No.: D3-A05101EN 2 2 φ3+0.0 −0.2 2 VCC VOUT GND 26.5 1 2 3 2 4.5 Optical center φ3+0.0 −0.2 2 7.8 2 1 GP2A200LCS0F Series Date code (2 digit) 1st digit Year of production A.D. Mark 2000 0 2001 1 2002 2 2003 3 2004 4 2005 5 2006 6 2007 7 2008 8 2009 9 2010 0 : : 2nd digit Month of production Month Mark 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 X 11 Y 12 Z repeats in a 10 year cycle Country of origin Japan Sheet No.: D3-A05101EN 3 GP2A200LCS0F Series ■ Absolute Maximum Ratings Parameter Supply voltage Output voltage *1 Output current *2 Operating temperature *2 Storage temperature ∗ ∗ Symbol VCC VO IOL Topr Tstg Rating −0.5 to +7 30 50 −10 to +70 −20 to +80 (Ta=25˚C) Unit V V mA ˚C ˚C 1 Sink current refer to Fig.5. 2 The connector should be plugged in/out at normal temperature. ■ Electro-optical Characteristics Parameter Supply voltage Current dissipation (I) *3 Current dissipation (II) Low level output voltage High level output voltage *4 Non detection distance GP2A210LCSJF *4 Symbol VCC ICC ICCP VOL VOH LLHL LHLS Condhitions − Smoothing value VCC=5V, RL=∞ Pulse peak value VCC=5V VCC=5V, IOL=16mA, at detecting time VCC=5V, RL=1kΩ, at non detecting time KODAK Gray Cards, VCC=5V KODAK Gray Cards, VCC=5V Black paper, VCC=5V KODAK Gray Cards , VCC=5V Black paper, VCC=5V VCC=5V − Detection distance LHLL *5 Response time Acceptable illuminance *6 tPLH tPHL Ev1 Ev2 MIN. 4.75 − − − 4.5 − − − − 22 15 − − 3 000 1 500 TYP. − − − − − − − − − − − − − − − MAX. 5.25 30 150 0.4 − 90 70 2 5 − − 1 1 − − (Ta=25˚C) Unit V mA mA V V mm mm mm ms ms lx lx ∗ ∗ ∗ 3 Refer to Fig.1. 4 Refer to Fig.2. 5 Refer to Fig.3. * 6 Refer to Fig.4. Reflective object Black paper (black) : Standard reflective object (provided by SHARP Corporation) KODAK Gray Cards (use the white side reflects about 90%) : Standard reflective object (provided by SHARP Corporation) PPC paper : Standard reflective object (provided by SHARP Corporation) Sheet No.: D3-A05101EN 4 GP2A200LCS0F Series Fig.1 Test Condition for Peak Pulse Value ICCP R=1Ω 1 2 3 V RL=1kΩ VO GND tW tP ICCP=Vr/1Ω tW (TYP.)=8μs (GP2A240LCS0F : 2.5 to 9.3μs) tP (TYP.)=130μs (GP2A240LCS0F : 40 to 150μs) Photointerrupter Fig.2 Test Condition for Detecting Distance Characteristics Output VO Reflective object VOH VOL Detecting distance L LHLS LHLL LLHS LLHL Detection surface Fig.3 Test Circuit for Response Time Reflective object Detection surface 1 2 3 With reflective object RL=1kΩ VCC=5V VO GND VOUT waveform tPHL tPLH VOH 1.5V VOL Without reflective object L Photointerrupter Fig.4 Test Condition for External Disturbing Light Illuminance EV1 : At non-detecting Emission/detection surface Light source A Photointerrupter Illuminance shall be that on the emission/detection surface. Output shall not go from "H" to "L". Light source A EV2 : At detecting PPC paper Emission/detection surface Photointerrupter Illuminance shall be that on the reflective object. Output shall not go from "L" to "H". 15mm Vr VCC=5V Sheet No.: D3-A05101EN 5 GP2A200LCS0F Series Fig.5 Output Current vs. Ambient Temperature 50 Fig.6 Low Level Output Voltage vs. Ambient Temperature 0.3 VCC=5V At detecting IOL=30mA 0.2 16mA 40 30 20 Low level output voltage VOL (V) Output Current IOL (mA) 0.1 5mA 10 0 −10 0 25 50 70 75 100 0 −10 0 10 20 30 40 50 60 70 Ambient temperature Ta (C) Ambient temperature Ta (C) Fig.7 Low Level Output Voltage vs. Low Level Output Current VCC=5V At detecting Low level output voltage VOL (V) Fig.8 Dissipation Current(Smoothing Value) vs. Ambient Temperature 7 Ta=−10˚C 6 Dissipation current ICC (mA) 5 4 3 2 1 25˚C 70˚C 0.1 0.01 1 10 Low level output current IOL (mA) 100 0 4.75 4.85 4.95 5.05 5.15 5.25 Supply voltage VCC (V) Remarks : Please be aware that all data in the graph are just for reference and not for guarantee. Sheet No.: D3-A05101EN 6 GP2A200LCS0F Series ■ Design Considerations ● Design guide 1) VO terminal : Open collector output This product operates the light emitter by pulse drive. Please supply the stable supply voltage in order to prevent error operation by pulse current. Please use this device after connecting a capacitor between VO and GND for prevention of line noise. 2) Prevention of detection error Please be careful that you need to keep the direct inverter light away from the photo detecting surface since the device will not operate correctly in such case. In addition, we recommend to make sure the operation test in the actual application. 3) Plugging in/out The connector should be plugged in/out at normal temperature. This product is not designed against irradiation and incorporates non-coherent IRED. ● Parts This product is assembled using the below parts. • Photodetector (Q'ty : 1) [Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit] Category Phototransistor Maximum Sensitivity wavelength (nm) 900 Sensitivity wavelength (nm) 700 to 1 200 Response time (μs) 400 • Photo emitter (Q'ty : 1) Category Infrared emitting diode (non-coherent) Material Gallium arsenide (GaAs) Maximum light emitting wavelength (nm) 950 I/O Frequency (MHz) 0.3 • Material Case GP2A200LCS0F GP2A200LCSCF GP2A210LCSJF∗ GP2A240LCS0F Black polyphernylene Sulfide resin (UL94 V-0) Polycarbonate resin (UL94 V-2) Polycarbonate resin (Gray) (UL94 V-2) Polycarbonate resin (Navy Blue) (UL94 V-2) Lens Bottom cover ∗The IR-90 filter (Fuji Photo Film Co., Ltd.) is inserted between case and detector side lens. • Others Laser generator is not used. Sheet No.: D3-A05101EN 7 GP2A200LCS0F Series ■ Manufacturing Guidelines ● Cleaning instructions Polycarbonate resin is used as the material of the lens surface. So this product shall not be cleaned by cleaning solvent absolutely. Dust and stain shall clean by air blow, or shall clean by soft cloth. ● Presence of ODC This product shall not contain the following materials. And