MPK DC Capacitors GTO Clamping

MPK DC Capacitors Jump to preceding page GTO Clamping B 25 556 Extremely low self-inductance High volumetric efficiency Construction Self-healing Plastic and paper dielectric Oil-impregnated tubular windings (no PCB) Metal-sprayed end faces ensure reliable contacting q Fully insulated case q q q q Terminals q Internal thread M8 × 10, axial Mounting q On the terminals Individual data sheets One capacitor of this series is specified in detail (incl. thermal data) on page 96. Upon request, these data sheets are available for each capacitor type. www.DataSheet4U.com Technical data Standards IEC 1071-1/2 EN 61071-1/2 VDE 0560 part 120 and 121 ≤ 20 · 10 –4 ≤ 80 A – 25 °C + 85 °C ≤ 95 % 300 failures per 109 component hours 100000 h – 55/+ 85 °C 25/085/56 – 25 °C + 85 °C 56 days/40 °C/93 % rel. humidity Dielectric dissipation factor Max. current Climatic data: Min. operating temperature Max. operating temperature Average relative humidity Failure quota Load duration Storage temperature limit IEC climatic category (IEC 68-1 and 2) Test A, cold Test B, dry heat Test Ca, damp heat, steady state tan δ0 Imax Θmin Θmax αFQ(co) tLD(co) Θstg 94 Siemens Matsushita Components B 25 556 GTO Clamping Technical data IEC climatic category (IEC 68-1 and 2) Values after test Ca: Capacitance change Self-discharge time constant τ = Dissipation factor change Test data: DC test voltage between terminals Self-discharge time constant τ = Dissipation factor (50 Hz) Dimensional drawing Internal thread M8 x 10 25/085/56 ∆C /C R is · C ∆tan δ ≤1% ≥ 10000 s ≤ 5 · 10 –4 1,5 · UN, 10 s ≥ 10000 s ≤ 25 · 10 –4 UTT R is · C ∆tan δ ø22 ∅ dmax mm 83 93 98 I –2 mm 163 163 163 l _2 ø22 Internal thread M8 x 10 KLK1341-5 Dimensions in mm Available ratings UN (V) CN1) 7,5 9 12 (µF) DC 2300 3 min. ød max. 3 min. 3400 1) Capacitance tolerance ± 10 % Siemens Matsushita Components 95 B 25 556 GTO Clamping 9 µF / 3400 Vdc Ordering code: B25556-J3905-K003 Characteristics 9 µF ± 10 % DC 3400 V 70 A < 20 nH 17 · 10 –4 3,8 mΩ ø22 Internal thread M8 x 10 CN, tol. UN Imax Lself tan δ0 RS 163 _ 2 Maximum ratings û us î Is (du/dt)max (du/dt)s Test data 4300 V 5100 V 5,4 kA 14,0 kA 600 V/µs 1500 V/µs ø22 Internal thread M8x10 KLK1589-7 UTT DC 5100 V, 10 s Ris · C ≥ 10000 s tan δ (50 Hz) ≤ 22 · 10 –4 Climatic data Θmin Θmax Humidity αFQ(co) tLD(co) Θstg – 25 °C + 85 °C Average relative humidity ≤ 95 % 300/109 h 100000 h – 55 to + 85 °C Design data Dimensions ∅ × l Approx. weight Impregnation Terminals Max. torque Terminal cross section Fully insulated 98 mm × 163 mm 1700 g Oil Internal thread M8 × 10 7 Nm 16 mm2 IEC climatic category: 25/085/56 (IEC 68-1 and 2) Θ test Rel. humidity ttest ∆C /C ∆ tan δ Ris · C + 40 °C 93 % 56 days ≤1% ≤ 5 · 10 –4 ≥ 10000 s Without overpressure disconnector 96 Siemens Matsushita Components 3 min. ø98 max. 3 min. B 25 556 Jump to succeding page GTO Clamping Thermal data B25556-J3905-K003 Dielectric power dissipation PD versus repetition frequency f0 ûac = 600 V ûac = 540 V Ohmic power dissipation PR versus rms current value I RS (85 °C) = 4,6 mΩ Permissible ambient temperature ΘA versus total power dissipation P (Upright mounting position) Natural cooling Forced cooling 2 m/s Permissible capacitor temperature Siemens Matsushita Components 97