Description
Document Version: 3 Date: 2003/03/15 www.DataSheet4U.com Product Functional Specification 15.4 inch WXGA Color TFT LCD Module Model Name : B154EW01 V0 ( u) Preliminary Specification ( ) Final Specification Note: This Specification is subject to change without notice. (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 1/30 No Reproduction and Redistribution Allowed. I. Contents 1.0 2.0 Handling Precautions General Description 2.1 Characteristics 2.2 Functional Block Diagram 3.0 4.0 5.0 www.DataSheet4U.com Absolute Maximum Ratings Optical Characteristics Signal Interface 5.1 Connectors 5.2 Signal Pin 5.3 Signal Description 5.4 Signal Electrical Characteristics 5.5 Signal for Lamp Connector 6.0 7.0 8.0 Pixel Format Image Parameter Guide Line for CFL Inverter Interface Timings 8.1 Timing Characteristics 8.2 Timing Definition 9.0 10.0 11.0 12.0 Power Consumption Power ON/OFF Sequence Reliability Test Condition Mechanical Characteristics 12.1 LCM Outline Dimension 12.2 Screw Hole Depth and Center Position 13.0 14.0 15.0 Shipping Label Format Carton package Shipping package of palletizing sequence II Record of Revision Version and Date Page Old description New Description Remark (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 2/30 No Reproduction and Redistribution Allowed. 0.1. 2003/08/13 0.2. 2003/12/22 All 5 5 18 23 First Edition for Customer Weight: 580g CCFL Frequency: 55KHz-65KHz All Weight: 585g Add surface treatment CCFL Frequency: 50KHz-70KHz Mechanical drawing updated Add description of screw hole length and torque Add carton package description 0.3 2004/03/15 25 27 1.0 Handing Precautions www.DataSheet4U.com 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a Module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source(2.11, IEC60950 or UL1950), or be applied exemption. (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 3/30 No Reproduction and Redistribution Allowed. 14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit(2.4, IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit. www.DataSheet4U.com (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 4/30 No Reproduction and Redistribution Allowed. 2.0 General Description B154EW01 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a driver circuit, and backlight system. The screen format is intended to support the WXGA (1280(H) x 800(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface compatible. Inverter card of backlight is not included. B154EW01 V0 is designed for a display unit of notebook style personal computer and industrial machine. . www.DataSheet4U.com (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 5/30 No Reproduction and Redistribution Allowed. 2.1 Display Characteristics The following items are characteristics summary on the table under 25 ℃ condition: ITEMS Unit SPECIFICATIONS Screen Diagonal Active Area Pixels H x V Pixel Pitch www.DataSheet4U.com [mm] [mm] 391mm 331.2 X 207.0 1280x3(RGB) x 800 [mm] 0.2588X0.2588 R.G.B. Vertical Stripe Normally White Pixel Arrangement Display Mode Typical White Luminance (ICFL=6.0mA) Luminance Uniformity Contrast Ratio Optical Rise Time/Fall Time Nominal Input Voltage VDD Typical Power Consumption (VDD line + VCFL line) Weight Physical Size Electrical Interface Surface Treatment Support Color Temperature Range Operating Storage (Non-Operating) [oC] [oC] [msec] [Volt] [Watt] [Grams] [mm] [cd/m2] 195 min (5 point average) 220 Typ. (5 point average) 1.25 max. (5 pts) 1.50 max. (13pts) 400 18/7 +3.3 Typ. 6.5W max 585g typ. 344x 222.0 x 6.5 max. 1 channel LVDS Anti-glare, Harness 3H, Haze 25%, Reflectance 4.3% Native 262K colors ( RGB 6-bit data driver ) 0 to +50 -20 to +60 (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 6/30 No Reproduction and Redistribution Allowed. 2.2 Functional Block Diagram The following diagram shows the functional block of the 15.4 inches Color TFT/LCD Module: LCD DRIVE CARD www.DataSheet4U.com color data 6bit Backlight Unit for R/G/B DSPTMG Vsync Hsync (3 pairs LVDS) DTCLK (1 pair LVDS) VDD GND LCD Controller TFT ARRAY/CELL 1280(R/G/B) x 3 x 800 Y-Driver X-Driver DC-DC Converter Ref circuit LCD Connector JAE Mating Type JAE FI-XB30SL-HF10 JAE FI-S30M Lamp Connector JST BHSR-02VS-1 Mating Type SM02B-BHSS-1 (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 7/30 No Reproduction and Redistribution Allowed. 3.0 Absolute Maximum Ratings Absolute maximum ratings of the module is as following: Item Symbol Min Max Logic/LCD Drive Voltage Input Voltage of Signal CCFL Current CCFL Ignition Voltage www.DataSheet4U.com Unit [Volt] [Volt] [mA] rms Vrms [ oC] [%RH] [ oC] [%RH] G Hz G ms Conditions VDD Vin ICFL Vs TOP HOP TST HST -0.3 -0.3 0 8 -20 5 +4.0 VDD+0.3 6.5 1000 +50 95 +60 95 1.5 10-500 (random) 220 , 2 Operating Temperature Operating Humidity Storage Temperature Storage Humidity Vibration Shock(Non-operating) Note 1 Note 1 Note 1 Note 1 2hrs/axis, X,Y,Z Half sine wave Note 1 : Maximum Wet-Bulb should be 39℃ and No condensation. (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 8/30 No Reproduction and Redistribution Allowed. 3.1 Wet-Bulb temperature chart Twb=39° C www.DataSheet4U.com Operating Range Storage Range (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 9/30 No Reproduction and Redistribution Allowed. 4.0 Optical Characteristics The optical characteristics are measured under stable conditions as follows under 25 ℃ condition: Item Conditions Typ. Note Viewing Angle K: Contrast Ratio Contrast ratio www.DataSheet4U.com Horizontal (Right) [degree] K = 10 (Left) Vertical [degree] K = 10 (Upper) (Lower) 70 70 60 60 400 1.25 max. (5 pts) 1.50 max. (13pts) Note 4, Note 6 Note 4,Note 6 Note 4 Note 1, Note 2,Note 3, Note 4 Note 5 Note 7 Note 7 Note 4 Luminance Uniformity Cross talk Response Time (Room Temp.) Color Chromaticity Coordinates (CIE) % [msec] [msec] Rising Falling Red Red Green Green Blue Blue White White White Luminance (CCFL 6.0 mA) [cd/m ] 2 4% max 18 7 x y TBD TBD TBD TBD TBD TBD 0.313+/-0.03 0.329+/-0.03 x y x y x y 195min(5 points average) Note 1, Note 2, Note 4 220 (5 points average) (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 10/30 No Reproduction and Redistribution Allowed. Note 1: 5 points position (Display area : 331.2mm x 207.0mm) W W /4 W /4 W /4 W /4 H /4 1 H /4 H H /4 2 3 www.DataSheet4U.com H /4 4 5 Note 2: 13 points position W W /4 10 10 H /4 W /4 W /4 W /4 10 1 4 2 5 3 H /4 H H /4 6 7 8 9 H /4 10 10 12 13 11 Note 3: The luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the minimum test point luminance Maximum Brightness of five points δW5 = Minimum Brightness of five points Maximum Brightness of thirteen points δW13 = Minimum Brightness of thirteen points (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 11/30 No Reproduction and Redistribution Allowed. Note 4: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room. Photodetector (BM-5A,BM-7 or www.DataSheet4U.com Field= 2 50 cm LCD Panel TFT-LCD Module Center of the screen Note 5： Definition of Cross Talk (CT) CT = | YB – YA | / YA × 100 (%) Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) (C) Copyright AU Optronics, Inc. August, 2003 All Rights Reserved. B154EW01 V0 Ver.3 12/30 No Reproduction and Redistribution Allowed. Note 6: Definition of response time: The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to “White” (falling tim

Part Number
B154EW01

Free Sample / Buy Component / Product Information
Locate Part B154EW01

Datasheet
Locate DataSheet

B154EW01 Cross Reference : Jump New Window
Get Cross-Reference Datasheet