Color-TV AV-Switch IC

ICs for TV AN5829S Sound multiplex decoder IC for the U.S. televisions s Overview 0.4±0.25 0.45 Unit: mm 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 The AN5829S is a multiplex sound demodulation IC dedicated to the U.S. television and incorporates a bidirectional I2C interface (adjustment, mode SW), an AGC circuit and external stereo input switches (2 systems). • Stereo demodulation, SAP demodulation, dbx noise reduction, AGC, external stereo input SW and I2C bus interface are integrated in a single chip • Bi-directional I2C bus makes it possible to monitor MPX input level, separation adjustment (3 places), mode changeover and receiving status. • Eliminated external parts (multi-sound block: 21 pieces → 14 pieces • Lower power dissipation (VCC = 5 V, ITOT = 18 mA) 0.1±0.1 1.27 s Features 0.3 7.2±0.3 9.4±0.3 SOP024-P-0375A s Applications • Televisions and VCRs for the North American market 0.15 0.925 2.0±0.2 15.3±0.3 1 2 R out L out 4 1 AN5829S GND s Block Diagram VCC 7 17 16 15 Out SW I2C Decoder Offset cancel Matrix AGC DAC 21 22 ZAP 18 19 20 PE SCL SDA L+R demod L+R filter Pilot det. 75 µs De-emph. 24 23 2 3 L−R demod Wide band expand L−R filter Offset cancel 5 Wide band RMS det. Wide band filter 8 6 SAP det. Noise det. Spectral expand Spectral RMS det. Spectral filter 11 10 (L−R)/SAP switch dbx De-emph. fH, 2fH Trap filter 13 12 AUX2 L AUX2 R AUX1 L AUX1 R St. PLL Pilot cancel Stereo filter MPX in SAP demod SAP out filter 14 Input VCA SAP filter Noise filter 9 ICs for TV ICs for TV s Pin Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 AGC timing External input 1 L-ch External input 1 R-ch 75 µs filter offset cancel dbx offset cancel Wideband timing VCC Wideband level sensor input Spectral filter Spectral timing Spectral level sensor input SAP noise level detection Description Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Description SAP carrier detection Composite input Pilot signal detection Stereo PLL filter GND SCL SDA PE for ZAP L-ch output R-ch output External input 2 R-ch. External input 2 L-ch. AN5829S s Absolute Maximum Ratings Parameter Supply voltage Supply current Power dissipation *2 *1 Symbol VCC ICC PD Topr Tstg Rating 6.0 25 150 −20 to +75 −55 to +125 Unit V mA mW °C °C Operating ambient temperature Storage temperature *1 Note) The use of this IC, which builds in dbx-TV noise reduction, requires a license agreement with THAT Corporation. *1: Except fot the operating ambient temperature and storage temperature, all ratings are for Ta = 25°C. *2: Ta = 75°C s Recommended Operating Range Parameter Supply voltage Symbol VCC Range 4.5 to 5.5 Unit V 3 AN5829S s Electrical Characteristics at VCC = 5 V, NR: On,Ta = 25°C Input level (at 100% modulation) L+R: 75 mV[rms] (pre-emphasis off) L−R: 150 mV[rms] (dbx noise reduction off) Pilot: 15 mV[rms] SAP: 45 mV[rms] (dbx noise reduction off) Parameter Total circuit current Mono output level Symbol ICC V0(MON) No signal f = 1 kHz, (mono) 100%mod f = 300 Hz, (mono) 30%mod f = 8 kHz, (mono) 30%mod f = 1 kHz, (mono) 100%mod Input short-circuit, BPF (A curve) f = 1 kHz, (mono) 100%mod f = 1 kHz, (L(R)-only) 100%mod f = 300 Hz, (L(R)-only) 30%mod f = 3 kHz, (L(R)-only) 30%mod f = 8 kHz, (L(R)-only) 30%mod f = 1 kHz, (L(R)-only) 100%mod f = 15.73 kHz, (fH), 15 mV[rms] fH, 2 fH Trap+BPF f = 15.73 kHz (fH) f = 15.73 kHz (fH) f = 1 kHz, (SAP) 100%mod f = 300 Hz, (SAP) 30%mod f = 3 kHz, (SAP) 30%mod f = 1 kHz, (SAP) 100% f = 78.7 kHz, (5fH),V= 45 mV[rms], BPF f = 78.7 kHz, (5fH) f = 78.7 kHz, (5fH) (SAP)1 kHz, 100%mod (Stereo) pilot-signal (Stereo) 1 kHz, 100%mod (SAP) carrier-signal (SAP) 1 kHz, 100%mod (Mono) 1 kHz, 100%mod (SAP) carrier-signal f = 1 kHz, VIN = 500 mV[rms] INT: (mono) 1 kHz, 100%mod EXT: f = 1 kHz, 500 mV[rms] INT: (mono) 1 kHz, 100%mod EXT: f = 1 kHz, 500 mV[rms] Conditions Min 11 430 − 0.5 −1.2   − 0.5 380 − 0.7 −1 −2.5   4 0.5 370 −1 −2.5   11 0.5        Typ 18 480 0 − 0.1   0 480 0 0 − 0.5   8  500 0 − 0.5            ICs for TV Max 25 Unit mA 530 mV[rms] 0.5 0.7 0.7 −60 0.5 dB dB % dBV dB Mono frequency characteristics-1 V1(MON) Mono frequency characteristics-2 V2(MON) Mono distortion ratio Mono noise level THD(MON) VN(MON) (L), (R) output voltage difference VLR(MON) Stereo output level V0(ST) 580 mV[rms] 0.7 1 1.5 1 −60 13 5 dB dB dB % dBV mV[rms] dB Stereo frequency characteristics-1 V1(ST) Stereo frequency characteristics-2 V2(ST) Stereo frequency characteristics-3 V3(ST) Stereo distortion ratio Stereo noise level Stereo discrimination level THD(ST) VN(ST) VTH(ST) Stereo discrimination hysteresis VHY(ST) SAP output level V0(SAP) 680 mV[rms] 1 1 1.5 −70 26 5 −50 −50 −50 −56 50 50 50 dB dB % dBV mV[rms] dB dB dB dB dB dB dB dB SAP frequency characteristics-1 V1(SAP) SAP frequency characteristics-2 V2(SAP) SAP distortion ratio SAP noise level SAP discrimination level SAP discrimination hysteresis SAP → Stereo crosstalk Stereo → SAP crosstalk SAP → Mono crosstalk Mono → SAP crosstalk AUX 1, AUX 2 to INT crosstalk INT, AUX 2 to AUX 1 crosstalk INT, AUX 1 to AUX 2 crosstalk 4 THD(SAP) VN(SAP) VTH(SAP) VHY(SAP) CT1 CT2 CT3 CT4 CT5 CT6 CT7 ICs for TV s Electrical Characteristics at VCC = 5 V, NR: On,Ta = 25°C (continued) Parameter AGC gain 1*1 *1 AN5829S Symbol VAGC1 VAGC2 Conditions f = 1 kHz, VIN(EXT) = 50 mV[rms] f = 1 kHz, VIN(EXT) = 500 mV[rms] Min 67 180 Typ 100 270 Max Unit 140 mV[rms] 390 mV[rms] AGC gain 2 I2 C interface IACK VIHI VILO fImax Maximum pin 2 sink current at ACK    1 3.5 0  2    20 5.0 0.9 100 mA V V kbit/s Sink current at ACK SCL, SDA signal input high level SCL, SDA signal input low level Input available maximum frequency Note) *1: 00H register: D7 = 0, D6 = 1 • Design reference data Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed. Parameter Stereo separation (100%)-1 Stereo separation (100%)-2 Stereo separation (100%)-3 Stereo separation (100%)-4 Stereo separation (30%)-1 Stereo separation (30%)-2 Stereo separation (30%)-3 Stereo separation (30%)-4 Stereo separation (10%)-1 Stereo separation (10%)-2 Stereo separation (10%)-3 Stereo separation (10%)-4 I2 C interface Symbol Sep100-1 Sep100-2 Sep100-3 Sep100-4 Sep30-1 Sep30-2 Sep30-3 Sep30-4 Sep10-1 Sep10-2 Sep10-3 Sep10-4 Conditions f = 300 Hz, (L(R)-only) 100%mod f = 1 kHz, (L(R)-only) 100 %mod f = 3 kHz, (L(R)-only) 100%mod f = 8 kHz, (L(R)-only) 100%mod f = 300 Hz, (L(R)-only) 30%mod f = 1 kHz, (L(R)-only) 30%mod f = 3 kHz, (L(R)-only) 30%mod f = 8 kHz, (L(R)-only) 30%mod f = 300 Hz, (L(R)-only) 10%mod f = 1 kHz, (L(R)-only) 10%mod f = 3 kHz, (L(R)-only) 10%mod f = 8 kHz, (L(R)-only) 10%mod             Min 20 17 20 10 22 20 22 14 20 20 20 14 Typ 35 28 35 18 35 35 35 22 35 35 30 22             Max                  1.0 0.35   3.5   Unit dB dB dB dB dB dB dB dB dB dB dB dB µs µs µs µs µs µs µs µs µs µs µs µs Bus free before start Start condition set-up time Start condition hold time Low period SCL, SDA High period SCL Rise time SCL, SDA Fall time SCL, SDA Data set-up time (write) Data hold time (write) Acknowledge set-up time Acknowledge hold time Stop condition set-up time tBUF tSU.STA tHD.STA tLO tHI tr tf tSU.DAT tHD.DAT tSU.ACK tHD.ACK tSU.STO 4.0 4.0 4.0 4.0 4.0   0.25 0.3  0 4.0 5 AN5829S s Electrical Characteristics at VCC = 5 V, NR: On,Ta = 25°C (continued) Start condition Slave address ACK Sub address ACK Data byte ICs for TV Stop condition ACK SDA tBUF SCL tSU.STA tHDSTA tr tf tHI tLO tSU.DAT tHD.DAT tLO tSU.STO s Terminal Equivalent Circuits Pin No. 1 Equivalent circuit VCC Description AGC: AGC level sensor pin DC voltage (V) 0.5 to 2.0 425 Ω 51 kΩ 1 500 Ω GND 2 VCC AUXIL: External input1 L-ch input pin 2.2 2 20.7 kΩ 13.8 kΩ 2.2 V GND 3 VCC AUXIR: External input 1 R-ch input pin 2.2 3 20.7 kΩ 13.8 kΩ 2.2 V GND 6 ICs for TV s Terminal Equivalent Circuits (continued) Pin No. 4 Equivalent circuit VCC AN5829S Description OFCAN1: 75 µs filter output Offset cancel pin DC voltage (V) 2.2 524 Ω 4 80 kΩ 80 kΩ 2.2 V GND 5 VCC OFCAN2: dbx output Offset cancel pin 2.2 524 Ω 5 80 kΩ 80 kΩ 2.2 V GND 6 7.5 µΑ VCC WBTIME: Wide expander effective value detection recovery time set-up pin 2.2 6 29 Ω 29 Ω 15 µΑ GND 7 8  VCC VCC: VCC pin WBDET: RMS detection circuit input pin of wide band expander VCC 2.2 8 14.4 kΩ 2.2 V GND 7 AN5829S s Terminal Equivalent Circuits (continued) Pin No. 9 230 Ω 18 kΩ ICs for TV Equivalent circuit VCC Description SPEFIL: Variable de-emphasis level adjusting pin DC voltage (V) 2.2 9 230 Ω 18 kΩ 2.2 V GND 10 7.5 µΑ VCC SPETIME: RMS detection recovery time pin of variable de-emphasis 0.2 10 29 Ω 29 Ω 15 µΑ GND 11 VCC SPEDET: RMS detection circuit input pin of variable de-emphasis 2.2 11 3.2 kΩ 2.2 V GND 12 VCC NOISEDET: Noise detecting pin of SAP malfunction-prevention-circuit(Mute SAP demodulation at detecting noise.) VCC − 2 VBE 141 kΩ 12 GND 8 ICs for TV s Terminal Equivalent Circuits (continued) Pin No. 13 Equivalent circuit VCC AN5829S Description SAPDET: SAP signal carrier level detection pin DC voltage (V) VCC − 2 VBE 163 kΩ 13 GND 14 VCC MPXIN: Composite signal input pin 2.2 14 524 Ω 54.4 kΩ 2.2 V GND 15 VCC PILOTDET: Stereo pilot signal detection pin 2.2VCC − 2 VBE 136 kΩ 15 GND 16 VCC PLL: Stereo PLL low pass filter connection pin VCC − 2 VBE 58 kΩ 16 GND 17  GND: GND pin 0 9 AN5829S s Terminal Equivalent Circuits (continued) Pin No. 18 51 kΩ ICs f