High Dynamic Range Amplifier

www.DataSheet4U.com High Dynamic Range Amplifier AH2 The Communications Edge TM Product Information Product Features x x x x x x x x 50 – 1000 MHz +40 dBm OIP3 -71dBc CTB -48dBc CSO 3.5 dB Noise Figure 14.5 dB Gain +20 dBm P1dB Lead-free/Green/RoHS-compliant SOT-89 Package x Single +5 V Supply x MTTF > 100 years Product Description The AH2 is a general purpose, high dynamic range amplifier targeting cable TV markets. The combination of gain flatness, high linearity and bandwidth make it ideal for CATV distribution, cable modem and laser diode driver applications. The AH2 is designed for 75 ohm systems and can operate directly from a +5 Volt DC regulator. The device is manufactured using reliable GaAs MESFET technology and boasts an MTBF of >100 years at a mounting temperature of +85 °C. It is available in the environmentally-friendly lead-free/green/RoHS-compliant SOT-89 package. All devices are 100% RF and DC tested. Functional Diagram GND 4 1 RF IN 2 GND 3 RF OUT Function Input Output/Bias Ground Pin No. 1 3 2, 4 Applications x CATV / DBS Specifications (1) Parameter Operational Bandwidth Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Noise Figure Operating Current Range Supply Voltage Typical Performance (3) Units MHz MHz dB dB dB dBm dBm dB mA V ¡ Min 50 13 Typ 800 14.5 14 17 +21 +40 3.5 150 5 Max 1000 Parameter Frequency S21 S11 S22 Output P1dB Output IP3 (2) Output IP2 (2) CTB (4) CSO (4) Xmod (4) Noise Figure Supply Voltage Device Current Units MHz dB dB dB dBm dBm dBm dBc dBc dBc dB V mA 100 14.5 -14 -17 +20 +40 +52 -71 -48 -65 3.5 Typical 860 13.2 -14 -17 +20 +40 +52 +37 120 180 1. Test conditions unless otherwise noted: T = 25 ºC, 50 system. 2. 3OIP measured with two tones at an output power of +5 dBm/tone separated by 10 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3.5 5 150 3. Parameters reflect performance in a single-ended 75 ohm circuit, as shown on page 3. 4. 77 channels 50 – 550MHz +34dBmV/channel, flat-loading Absolute Maximum Rating Operating Case Temperature Storage Temperature Supply Voltage RF Input Power (continuous) Junction Temperature Parameter Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice.         -40 to +85 qC -55 to +150 qC +6 V +10 dBm +220 qC Rating Ordering Information Part No. AH2-G AH2-PCB Description High Dynamic Range Amplifier Single-ended 75 ohm Application Circuit Board (lead-free/green/RoHS-compliant SOT-89 package) WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com Page 1 of 5 April 2006 www.DataSheet4U.com High Dynamic Range Amplifier AH2 The Communications Edge TM Product Information S-Parameters (VDS = +5 V, IDS = 150 mA, T = 25 C, unmatched device in a 75 ohm system) S-Parameters (VD = +5 V, ID = 150 mA, T = 25 C, calibrated to device leads in a 75 ohm system) Freq (MHz) S11 (dB) S11 (ang) ¢ ¢ Typical Device Data S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 -17.85 -18.10 -17.37 -16.63 -15.73 -14.91 -14.20 -13.45 -12.80 -12.18 -11.53 -11.04 -10.51 -10.02 -9.64 -9.22 -8.81 -8.48 -8.11 -7.81 -34.21 -38.37 -47.65 -55.66 -62.92 -70.31 -76.37 -81.85 -86.94 -91.91 -95.72 -99.60 -103.27 -106.94 -110.30 -113.34 -116.55 -119.17 -121.84 -124.91 14.88 14.92 14.89 14.74 14.86 14.61 14.64 14.62 14.60 14.53 14.34 14.26 14.19 14.10 14.02 13.96 13.83 13.69 13.54 13.44 172.97 171.11 168.59 165.97 162.85 160.05 157.30 154.45 151.27 148.33 146.02 143.33 140.39 137.75 134.99 132.29 129.84 127.70 125.28 122.82 -24.58 -24.56 -24.55 -24.53 -24.48 -24.45 -24.42 -24.34 -24.31 -24.32 -24.21 -24.18 -24.12 -24.11 -24.02 -23.93 -23.89 -23.85 -23.81 -23.77 4.81 2.30 1.69 1.17 0.72 0.58 0.44 0.16 -0.28 -0.47 -0.94 -1.00 -1.10 -1.54 -2.04 -2.63 -3.12 -3.33 -4.08 -4.42 -20.87 -21.20 -21.20 -20.82 -20.50 -20.36 -19.77 -19.23 -19.02 -18.49 -17.96 -17.84 -17.56 -16.97 -16.69 -16.42 -16.13 -15.87 -15.59 -15.42 -149.34 -158.61 -160.06 -159.44 -156.95 -155.78 -155.09 -152.65 -152.33 -151.93 -149.07 -148.36 -149.69 -149.32 -148.96 -148.88 -149.30 -149.09 -149.60 -150.68 Device S-parameters are available for download off of the website at: http://www.wj.com Input / Output Return Loss & Isolation 0 15 S11 S12 S22 14 -5 -10 -15 -20 -25 -30 0 200 400 600 800 1000 Gain Magnitude (dB) S21 (dB) 13 12 11 10 0 200 400 600 800 1000 Frequency (MHz) Frequency (MHz) Specifications and information are subject to change without notice.         WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com Page 2 of 5 April 2006 www.DataSheet4U.com High Dynamic Range Amplifier AH2 The Communications Edge TM Product Information Single – Ended CATV 75 : Evaluation Circuit: 50 – 860 MHz (AH2-PCB) Typical RF Performance at 25 qC Frequency S21 – Gain S11 – Input R.L. S22 – Output R.L. Output IP2 (+5 dBm) CAP +5 V ID=C4 C=1000 pF MHz 100 dB 14.5 dB -11.1 dB -9.5 dBm dBm 52.7 39.8 450 860 14.5 13.2 -12.7 -18.3 -22.9 -10.6 53.5 40.7 52.5 40.8 IND ID=L3 L=270 nH PORT P=1 Z=75 Ohm CAP ID=C1 C=1000 pF IND ID=L1 L=12 nH SUBCKT ID=S1 NET="AH2" CAP ID=C3 C=1000 pF PORT P=2 Z=75 Ohm Output IP3 (+5 dBm / tone, 10 MHz spacing) dB Noise Figure 3.9 3.1 3.2 Device Bias +5V @ 150mA CTB dBc -71 CSO dBc -48 XMOD dBc -65 77 channels, 50-550MHz, +34dBmV/channel flat loading CAP ID=C2 C=2.2 pF Circuit Board Material: .062” total thickness with a .028” FR-4 top RF layer, 4 layers (other layers added for rigidity), 1 oz copper, 75 Microstrip. Linearity vs. Frequency 60 Inpu / O ut R rnLoss t utp etu andIsolation Magnitude (dB) 0 Intercept Point (dBm) 50 40 30 20 10 0 0 200 400 600 800 1000 OIP3 OIP2 Magnitude (dB) -10 S 11 S 22 -20 -30 0 200 400 600 S 12 800 1000 Frequency (MHz) F en (M z) requ cy H N F oise igure CO S C , C O andX O V Freq TB S , M D s. uency -40 -50 -60 -70 CB T 77C hannel F Loading, +34dB V h. lat m /C 5 Intercept Point (dBm) Noise Figure (dB) 4 3 2 1 0 0 200 400 600 800 1000 dBc XO MD -80 0 100 200 300 400 500 600 Freq uency(M z) H Frequ (M z) ency H Specifications and information are subject to change without notice.         WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com £ 16 15.5 15 G ain 14.5 14 S -40C S 25C S 85C 21 21 21 0 200 400 600 800 1000 13.5 13 Frequ (M z) ency H IP2 and IP3 vs. Power Out at 450 MHz 55 50 45 40 35 30 25 -4 -2 0 2 4 6 8 10 IP2 IP3 Output power (dBm) Page 3 of 5 April 2006 www.DataSheet4U.com High Dynamic Range Amplifier Bias Vdd = 5 V, Id = 300mA AH2 The Communications Edge TM Product Information Push-Pull, 75 : CATV Reference Design: 50 – 860 MHz Frequency MHz 100 450 750 860 S21 dB 11.1 10.8 10.6 10.5 S11 dB -10.2 -9.7 -10.8 -11 S22 dB -13.3 -14.1 -15.4 -16.4 Output IP2 dBm 72 70 72 70 Output IP3 dBm 42 43 41 40 Noise Figure dB 5.5 4.3 5.0 5.4 CTB dBc -72 CSO dBc -75 XMOD dBc -68 77 channels, 50-550MHz, +34dBmV/channel flat loading S aram -P eters 15 80 S 21 Linearity vs. Frequency -60 -65 -70 -75 -80 0 200 400 600 800 1000 70 60 50 30 20 10 0 40 OIP3 OIP2 C , C O andX O V Freq TB S , M D s. uency 77C hannel F Loading, +34dB V h. lat m /C O P er utput ow XO MD RETURN LOSS (dB) 5 0 -5 Intercept Point (dBm) 10 -10 -15 -20 0 200 400 S 11 dBc CB T CO S S 22 600 800 1000 0 100 200 300 400 500 600 FR Q E C (M z) E UNY H Frequency (MHz) Freq uency(M z) H Specifications and information are subject to change without notice. ¤ ¤ ¤ ¤ WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com Page 4 of 5 April 2006 www.DataSheet4U.com High Dynamic Range Amplifier AH2 The Communications Edge TM Product Information This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260 qC reflow temperature) and leaded (maximum 245 qC reflow temperature) soldering processes. The plating material on the leads is NiPdAu. AH2-G (Green / Lead-free SOT-89 Package) Mechanical Information Outline Drawing Product Marking The AH2-G will be marked with an “AH2G” designator. An alphanumeric lot code (“XXXX-X” ) is also marked below the part designator on the top surface of the package. The obsolete tin-lead package is marked with an “AH2” designator followed by an alphanumeric lot code. Tape and reel specifications for this part are located on the website in the “Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: ESD Rating: Value: Test: Standard: Class 1B Passes 500V to <1000V Human Body Model (HBM) JEDEC Standard JESD22-A114 Class IV Passes 1000V to <2000V Charged Device Model (CDM) JEDEC Standard JESD22-C101 ¥ ¦ ¦ Land Pattern MSL Rating: Level 3 at +260 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Thermal Specifications Parameter Operating Case Temperature Thermal Resistance, Rth (1) Junction Temperature,