High Linearity InGaP HBT Amplifier

www.DataSheet4U.com AH115 The Communications Edge TM Product Information ½ Watt, High Linearity InGaP HBT Amplifier Product Features x 1800 – 2300 MHz x +28.5 dBm P1dB x +44 dBm Output IP3 x 14 dB Gain @ 1960 MHz x +5V Single Positive Supply x MTTF > 100 Years x Lead-free/green/RoHS-compliant SOIC-8 SMT Pkg. Product Description The AH115 is a high dynamic range driver amplifier in a low-cost surface mount package. The InGaP/GaAs HBT is able to achieve high performance for various narrow-band tuned application circuits with up to +44 dBm OIP3 and +28.5 dBm of compressed 1-dB power. All devices are 100% RF and DC tested. The AH115 is available in leadfree/green/RoHS-compliant SOIC-8 package. The product is targeted for use as driver amplifiers for wireless infrastructure where high linearity and medium power is required. The internal active bias allows the AH115 to maintain high linearity over temperature and operate directly off a +5 V supply. This combination makes the device an excellent fit for transceiver line cards and power amplifiers in current and next generation multi-carrier 3G base stations. Functional Diagram 1 8 7 6 5 2 3 4 Applications x Final stage amplifiers for Repeaters x Mobile Infrastructure Function Vref Input Output Vbias GND N/C or GND Pin No. 1 3 6, 7 8 Backside Paddle 2, 4, 5 Specifications (1) Parameters Operational Bandwidth Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) IS-95A Channel Power @ -45 dBc ACPR, 1960 MHz Typical Performance (4) Min 1800 12.5 2140 14.4 23 8 +28.5 +42 +22.5 +20 200 5.3 250 +5 300 Units MHz MHz dB dB dB dBm dBm dBm dBm dB mA V Typ Max 2300 Parameters Frequency Gain S11 S22 Output P1dB Output IP3 (2) IS-95A Channel Power @ -45 dBc ACPR, @ -45 dBc ACLR Units MHz dB dB dB dBm dBm dBm dBm dB Typical 1960 14.3 -12 -8 +28.3 +44 +22.5 +20 5 5.3 +5 V @ 250 mA ¡ +26.5 +41 2140 14.4 -23 -8 +28.5 +42 wCDMA Channel Power Noise Figure Supply Bias wCDMA Channel Power @ -45 dBc ACLR, 2140 MHz Noise Figure Operating Current Range (3) Device Voltage 4. Typical parameters reflect performance in a tuned application circuit at +25 C. 1. Test conditions unless otherwise noted. 25 ºC, Vsupply = +5 V in tuned application circuit. 2. 3OIP measured with two tones at an output power of +11 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. This corresponds to the quiescent current or operating current under small-signal conditions. It is expected that the current can increase up to 300mA at P1dB. Absolute Maximum Rating Operating Case Temperature Storage Temperature RF Input Power (continuous) Device Voltage Device Current Device Power Junction Temperature Parameter Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice         -40 to +85 qC -65 to +150 qC +22 dBm +8 V 400 mA 2W +250 qC Rating Ordering Information Part No. AH115-S8G AH115-S8PCB1960 AH115-S8PCB2140 Description 1960 MHz Evaluation Board 2140 MHz Evaluation Board (lead-free/green/RoHS-compliant SOIC-8 Pkg) ½ Watt, High Linearity InGaP HBT Amplifier WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com Page 1 of 5 April 2006 www.DataSheet4U.com ½ Watt, High Linearity InGaP HBT Amplifier S-Parameters (Vcc = +5 V, Icc = 250 mA, T = 25 C T = 25 C, calibrated to device leads) 35 30 25 G ain (dB) 20 10.0 0.2 0.4 0.6 0.8 1.0 2.0 3.0 4.0 0.2 AH115 The Communications Edge TM Product Information ¢ Typical Device Data 0. 8 6 0. 6 0. Gain and Maximum Stable Gain 0. 4 Swp Max 5.05GHz 2. 0 1.0 0.8 1.0 0 3. 0 4. 10.0 15 10 5 0 0 0.5 1 1.5 Frequency (GHz) 2 2.5 5.0 0 10.0 0.2 0.4 0.6 0.8 1.0 2.0 3.0 4.0 5.0 0 .4 -0 .4 -0 .0 -2 -0 .6 -0 .6 .0 -2 -0.8 Notes: The gain for the unmatched device in 50 ohm system is shown as the trace in black color. For a tuned circuit for a particular frequency, it is expected that actual gain will be higher, up to the maximum stable gain. The maximum stable gain is shown in the dashed red line. The return loss plots are shown from 50 – 5050 MHz, with markers placed at 0.5 – 5.05 GHz in 0.5 GHz increments. S-Parameters (Vcc = +5 V, Icc = 250 mA, T = 25 C, unmatched 50 ohm system, calibrated to device leads) Freq (MHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) £ Swp Min 0.05GHz -0 .8 -1.0 S12 (dB) S12 (ang) S22 (dB) -1.0 S22 (ang) 50 100 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 -2.11 -1.59 -1.51 -1.45 -1.58 -1.78 -1.96 -2.46 -3.30 -4.70 -8.15 -19.01 -9.59 -4.09 -1.99 -1.12 -0.72 -172.90 -178.94 173.71 163.84 153.68 144.31 134.21 123.44 111.21 92.57 78.58 93.29 177.56 159.30 141.65 127.57 116.11 25.10 21.15 17.75 15.23 13.69 12.77 11.94 11.36 11.17 11.39 11.64 11.51 10.35 7.87 4.95 1.97 -0.88 133.84 126.67 124.19 111.50 98.94 84.57 69.70 55.57 40.93 22.80 1.64 -25.24 -55.97 -83.78 -105.90 -122.86 -136.93 -36.03 -35.22 -34.29 -34.45 -33.58 -32.84 -32.77 -31.79 -31.12 -30.30 -29.47 -29.31 -30.51 -32.59 -33.96 -34.68 -35.64 31.44 15.04 7.30 -2.16 -2.99 -12.80 -18.76 -30.73 -45.14 -61.92 -83.99 -112.79 -150.45 177.62 137.14 109.27 81.83 -2.06 -2.73 -2.80 -2.73 -1.96 -1.68 -1.85 -2.14 -2.30 -2.52 -2.43 -1.84 -1.22 -1.06 -1.07 -1.19 -1.44 -105.55 -138.75 -160.44 -174.00 -179.13 172.00 166.98 164.05 163.07 164.84 164.25 162.38 155.68 147.58 139.74 132.15 125.05 Device S-parameters are available for download off of the website at: http://www.wj.com Application Circuit PC Board Layout Circuit Board Material: .014” Getek, 4 - layer, 1 oz copper, Microstrip line details: width = .026”, spacing = .026” The silk screen markers ‘A’, ‘B’, ‘C’, etc. and ‘1’, ‘2’, ‘3’, etc. are used as placemarkers for the input and output tuning shunt capacitors – C8 and C9. The markers and vias are spaced in .050” increments. Specifications and information are subject to change without notice         WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com Page 2 of 5 -4 .0 -5 . 0 -3 .0 -4 .0 -5. 0 2 -0. 2 -0 . Sw p Min 0.05GHz -10.0 0. 2 0 5. 0. 4 DB(GMax) DB(|S[2,1]|) 2. 0 -1 0.0 -3 .0 ¢ S11 S22 Sw p Max 5.05GHz 0 3. 0 4. 5. 0 10 .0 April 2006 www.DataSheet4U.com ½ Watt, High Linearity InGaP HBT Amplifier Typical RF Performance at 25 qC Frequency S21 – Gain S11 – Input Return Loss S22 – Output Return Loss Output P1dB Output IP3 (+11 dBm / tone, 1 MHz spacing) AH115 The Communications Edge TM Product Information 1960 MHz Application Circuit (AH115-S8PCB1960) 1960 MHz 14.3 dB -12 dB -8 dB +28.3 dBm +44 dBm +22.5 dBm 5 dB +5 V 250 mA Channel Power (@-45 dBc ACPR, IS-95 9 channels fwd) Noise Figure Device / Supply Voltage Quiescent Current S21 vs. Frequency 16 14 S21 (dB) S11 vs. Freqency 0 -5 S11 (dB) S22 (dB) S22 vs. Frequency 0 -5 -10 -15 -20 +25°C +85°C -40°C 1940 1950 1960 1970 1980 1990 12 10 8 6 1930 +25°C +85°C -40°C 1940 1950 1960 1970 1980 1990 -10 -15 -20 -25 1930 +25°C 85°C -40°C 1940 1950 1960 1970 1980 1990 Frequency (MHz) Frequency (MHz) -25 1930 Frequency (MHz) Noise Figure vs. Frequency 7 6 P1 dB (dBm) P1 dB vs. Frequency 30 29 ACPR (dBc) ACPR vs. Channel Power IS-95, 9 ch,Fwd, ±885 KHz offset, 30 KHz Meas BW, 1960 MHz -40 -45 -50 -55 -60 -65 -70 1940 1950 1960 1970 1980 1990 15 16 17 18 19 20 21 Frequency (MHz) +25°C +85°C -40°C 22 23 24 5 NF (dB) 4 3 2 1 0 1930 +25°C +85°C -40°C 1940 1950 1960 1970 1980 1990 28 27 26 25 24 1930 +25°C +85°C -40°C Frequency (MHz) Output Channel Power (dBm) OIP3 vs. Output Power freq=1960, 1961 MHz,+ 25° C OIP3 vs. Frequency +25°C, +11 dBm / tone OIP3 vs. Temperature freq=1960,1961 MHz, +11 dBm / tone 46 44 OIP3 (dBm) OIP3 (dBm) 46 44 42 40 38 36 1930 OIP3 (dBm) 46 44 42 40 38 36 1940 1950 1960 1970 1980 1990 42 40 38 36 8 10 12 14 16 Output Power (dBm) 18 20 -40 -15 10 35 60 85 Frequency (MHz) Temperature (°C) Specifications and information are subject to change without notice ¤ ¤ ¤ ¤ WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com Page 3 of 5 April 2006 www.DataSheet4U.com ½ Watt, High Linearity InGaP HBT Amplifier AH115 The Communications Edge TM Product Information 2140 MHz Application Circuit (AH115-S8PCB2140) Typical RF Performance at 25 qC Frequency S21 – Gain S11 – Input Return Loss S22 – Output Return Loss Output P1dB Output IP3 (+11 dBm / tone, 1 MHz spacing) 2140 MHz 14.4 dB -23 dB -8 dB +28.5 dBm +42 dBm +20 dBm 5.3 dB +5 V 250 mA Channel Power (@-45 dBc ACPR, IS-95 9 channels fwd) Noise Figure Device / Supply Voltage Quiescent Current S21 vs. Frequency 16 14 S11 (dB) S21 (dB) S11 vs. Frequency 0 -5 -10 -15 -20 -25 2110 +25°C +85°C S22 (dB) S22 vs. Frequency 0 -5 -10 -15 -20 -25 2110 +25°C +85°C -40°C 2120 2130 2140 2150 2160 2170 12 10 8 6 2110 +25°C +85°C -40°C 2120 2130 2140 2150 2160 2170 -40°C 2120 2130 2140 2150 2160 2170 Frequency (MHz) Frequency (MHz) 3GPP W-CDMA Test Model 1+64 DPCH, ±5 MHz offset, 2140 MHz Frequency (MHz) Noise Figure vs. Frequency 8 7 6 ACPR (dBc) ACPR vs. Channel Power P1 dB vs. Frequency 30 28 P1 dB (dBm) -35 -40 -45 -50 -55 -60 -65 +25°C +85°C -40°C NF (dB) 5 4 3 2 1 0 2110 2120 + 25°C +85°C -40°C 2130 2140 2150 2160 2170 26 24 22 +25°C +85°C -40°C 2120 2130 2140 2150 2160 2170 15 16 17 18 19 20 21 20 2110 Frequency (MHz) Output Channel Power (dBm) Frequency (MHz) OIP3 vs. Frequency +25°C, +11 dBm / tone freq. = 2140, 2141, +11 dBm / tone OIP3 vs. Temperature OIP3 vs. Output Power 45 43 OIP3 (dBm) 45 43 OIP3 (dBm) OIP3 (dBm) 45 43 41 39 37 35 freq. = 2140, 2141 MHz, 25° C 41 39 37 35 2110 41 39 37 35 2120 2130 2140 2150 Frequency (MHz)