Octal Transparent Latch with 3-STATE Outputs

74AC373 • 74ACT373 Octal Transparent Latch with 3-STATE Outputs November 1988 Revised November 1999 74AC373 • 74ACT373 Octal Transparent Latch with 3-STATE Outputs General Description The AC/ACT373 consists of eight latches with 3-STATE outputs for bus organized system applications. The flipflops appear transparent to the data when Latch Enable (LE) is HIGH. When LE is LOW, the data that meets the setup time is latched. Data appears on the bus when the Output Enable (OE) is LOW. When OE is HIGH, the bus output is in the high impedance state. Features s ICC and IOZ reduced by 50% s Eight latches in a single package s 3-STATE outputs for bus interfacing s Outputs source/sink 24 mA s ACT373 has TTL-compatible inputs Ordering Code: Order Number 74AC373SC 74AC373SJ 74AC373MTC 74AC373PC 74ACT373SC 74ACT373SJ 74ACT373MSA 74ACT373MTC 74ACT373PC Package Number M20B M20D MTC20 N20A M20B M20D MSA20 MTC20 N20A Package Description 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide Body 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 20-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide Body 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 20-Lead Shrink Small Outline Package (SSOP), EIAJ TYPE II, 5.3mm Wide www.DataSheet4U.com 20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 20-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering information Logic Symbols Connection Diagram IEEE/IEC Pin Descriptions Pin Names D0–D7 LE OE O0–O7 Description Data Inputs Latch Enable Input Output Enable Input 3-STATE Latch Outputs FACT is a trademark of Fairchild Semiconductor Corporation. © 1999 Fairchild Semiconductor Corporation DS009958 www.fairchildsemi.com 74AC373 • 74ACT373 Functional Description The AC/ACT373 contains eight D-type latches with 3STATE standard outputs. When the Latch Enable (LE) input is HIGH, data on the Dn inputs enters the latches. In this condition the latches are transparent, i.e., a latch output will change state each time its D-type input changes. When LE is LOW, the latches store the information that was present on the D-type inputs a setup time preceding the HIGH-to-LOW transition of LE. The 3-STATE standard outputs are controlled by the Output Enable (OE) input. When OE is LOW, the standard outputs are in the 2-state mode. When OE is HIGH, the standard outputs are in the high impedance mode but this does not interfere with entering new data into the latches. Truth Table Inputs LE X H H L OE H L L L Dn X L H X Outputs On Z L H O0 H = HIGH Voltage Level L = LOW Voltage Level Z = High Impedance X = Immaterial O0 = Previous O0 before HIGH-to-LOW transition of Latch Enable Logic Diagram Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. www.fairchildsemi.com 2 74AC373 • 74ACT373 Absolute Maximum Ratings(Note 1) Supply Voltage (VCC) DC Input Diode Current (IIK) VI = −0.5V VI = VCC + 0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO = −0.5V VO = VCC + 0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current per Output Pin (ICC or IGND) Storage Temperature (TSTG) Junction Temperature (TJ) PDIP 140°C ± 50 mA −65°C to +150°C ± 50 mA −20 mA +20 mA −0.5V to VCC + 0.5V −20 mA +20 mA −0.5V to VCC + 0.5V −0.5V to +7.0V Recommended Operating Conditions Supply Voltage (VCC) AC ACT Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) Minimum Input Edge Rate (∆V/∆t) AC Devices VIN from 30% to 70% of VCC VCC @ 3.3V, 4.5V, 5.5V Minimum Input Edge Rate (∆V/∆t) ACT Devices VIN from 0.8V to 2.0V VCC @ 4.5V, 5.5V 125 mV/ns Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation of FACT circuits outside databook specifications. 2.0V to 6.0V 4.5V to 5.5V 0V to VCC 0V to VCC −40°C to +85°C 125 mV/ns DC Electrical Characteristics for AC Symbol VIH Parameter Minimum HIGH Level Input Voltage VIL Maximum LOW Level Input Voltage VOH Minimum HIGH Level Output Voltage VCC (V) 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 VOL Maximum LOW Level Output Voltage 3.0 4.5 5.5 3.0 4.5 5.5 IIN (Note 4) IOZ Maximum Input Leakage Current Maximum 3-STATE Current 5.5 IOLD IOHD ICC (Note 4) Maximum Quiescent Supply Current Minimum Dynamic Output Current (Note 3) ±0.25 ± 2.5 µA 5.5 0.002 0.001 0.001 TA = +25°C Typ 1.5 2.25 2.75 1.5 2.25 2.75 2.99 4.49 5.49 2.1 3.15 3.85 0.9 1.35 1.65 2.9 4.4 5.4 2.56 3.86 4.86 0.1 0.1 0.1 0.36 0.36 0.36 ± 0.1 TA = −40°C to +85°C Guaranteed Limits 2.1 3.15 3.85 0.9 1.35 1.65 2.9 4.4 5.4 VIN = VIL or VIH 2.46 3.76 4.76 0.1 0.1 0.1 VIN = VIL or VIH 0.44 0.44 0.44 ± 1.0 µA V IOL = 12 mA IOL = 24 mA IOL = 24 mA (Note 2) VI = VCC, GND VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND 5.5 5.5 5.5 4.0 75 −75 40.0 mA mA µA VOLD = 1.65V Max VOHD = 3.85V Min VIN = VCC or GND V IOUT = 50 µA V IOH = −12 mA IOH = −24 mA IOL = −24 mA (Note 2) V IOUT = −50 µA V VOUT = 0.1V or VCC − 0.1V V Units Conditions VOUT = 0.1V or VCC − 0.1V Note 2: All outputs loaded, thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit @ 5.5V VCC. 3 www.fairchildsemi.com 74AC373 • 74ACT373 DC Electrical Characteristics for ACT Symbol VIH VIL VOH Parameter Minimum HIGH Level Input Voltage Maximum LOW Level Input Voltage Minimum HIGH Level Output Voltage VCC (V) 4.5 5.5 4.5 5.5 4.5 5.5 4.5 5.5 VOL Maximum LOW Level Output Voltage 4.5 5.5 4.5 5.5 IIN IOZ ICCT IOLD IOHD ICC Maximum Input Leakage Current Maximum 3-STATE Current Maximum ICC/Input Minimum Dynamic Output Current (Note 6) Maximum Quiescent Supply Current 5.5 5.5 5.5 5.5 5.5 5.5 4.0 0.6 0.001 0.001 TA = +25°C Typ 1.5 1.5 1.5 1.5 4.49 5.49 2.0 2.0 0.8 0.8 4.4 5.4 3.86 4.86 0.1 0.1 0.36 0.36 ± 0.1 ± 0.25 TA = −40°C to +85° Guaranteed Limits 2.0 2.0 0.8 0.8 4.4 5.4 3.76 4.76 0.1 0.1 0.44 0.44 ± 1.0 ± 2.5 1.5 75 −75 40.0 µA µA mA mA mA µA V Units V V V Conditions VOUT = 0.1V or VCC − 0.1V VOUT = 0.1V or VCC − 0.1V IOUT = −50 µA VIN = VIL or VIH V IOH = −24 mA IOH= −24 mA (Note 5) IOUT = 50 µA VIN = VIL or VIH V IOL = 24 mA IOL = 24 mA (Note 5) VI = VCC, GND VI = VIL, VIH VO = VCC, GND VI = VCC − 2.1V VOLD = 1.65V Max VOHD = 3.85V Min VIN = VCC or GND Note 5: All outputs loaded; thresholds on input associated with output under test. Note 6: Maximum test duration 2.0 ms, one output loaded at a time. AC Electrical Characteristics for AC VCC Symbol tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay Dn to On Propagation Delay Dn to On Propagation Delay LE to On Propagation Delay LE to On Output Enable Time Output Enable Time Output Disable Time Output Disable Time (V) (Note 7) 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 Note 7: Voltage Range 3.3 is 3.3V ± 0.3V Voltage Range 5.0 is 5.0V ± 0.5V TA = +25°C CL = 50 pF Min 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 Typ 10.0 7.0 9.5 7.0 10.0 7.5 9.5 7.0 9.0 7.0 8.5 6.5 10.0 8.0 8.0 6.5 Max 13.5 9.5 13.0 9.5 13.5 9.5 12.5 9.5 11.5 8.5 11.5 8.5 12.5 11.0 11.5 8.5 TA = −40°C to +85°C CL = 50 pF Min 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Max 15.0 10.5 14.5 10.5 15.0 10.5 14.0 10.5 13.0 9.5 13.0 9.5 14.5 12.5 12.5 10.0 ns ns ns ns ns ns ns ns Units www.fairchildsemi.com 4 74AC373 • 74ACT373 AC Operating Requirements for AC VCC Symbol tS tH tW Parameter Setup Time, HIGH or LOW Dn to LE Hold Time, HIGH or LOW Dn to LE LE Pulse Width, HIGH Note 8: Voltage Range 3.3 is 3.3V ± 0.3V Voltage Range 5.0 is 5.0V ± 0.5V TA = +25°C CL = 50 pF Typ 3.5 2.0 −3.0 −1.5 4.0 2.0 5.5 4.0 1.0 1.0 5.5 4.0 TA = −40°C to +85°C CL = 50 pF Guaranteed Minimum 6.0 4.5 1.0 1.0 6.0 4.5 ns ns ns Units (V) (Note 8) 3.3 5.0 3.3 5.0 3.3 5.0 AC Electrical Characteristics for ACT VCC Symbol Parameter (V) (Note 9) tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay Dn to On Propagation Delay Dn to On Propagation Delay LE to On Propagation Delay LE to On Output Enable Time Output Enable Time Output Disable Time Output Disable Time 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 Min 2.5 2.0 2.5 2.0 2.0 2.0 2.5 1.5 TA = +25°C CL = 50 pF Typ 8.5 8.0 8.5 8.0 8.0 7.5 9.0 7.5 Max 10.0 10.0 11.0 10.0 9.5 9.0 11.0 8.5 TA = −40°C to +85°C CL = 50 pF Min 1.5 1.5 2.0 1.5 1.5 1.5 2.5 1.0 Max 11.5 11.5 11.5 11.5 10.5 10.5 12.5 10.0 ns ns ns ns ns ns ns ns Units Note 9: Voltage Range 5.0 is 5.0V ± 0.5V AC Operating Requirements for ACT VCC Symbol tS tH tW Parameter Setup Time, HIGH or LOW Dn to LE Hold Time, HIGH or LOW Dn to LE LE Pulse Width, HIGH Note 10: Voltage Range 5.0 is 5.0V ± 0.5V TA = +25°C CL = 50 pF Typ 0.8 0 2.0 2.5 0 7.0 TA = −40°C to +85°C CL = 50 pF Guaranteed Minimum 3.5 1.0 8.0 ns ns ns Units (V) (Note 10) 5.0 5.0 5.0 Capacitance Symbol CIN CPD Parameter Input Capacitance Power Dissipation Capacitance Typ 4.5 40.0 Units pF pF VCC = OPEN VCC = 5.0V Conditions 5 www.fairchildsemi.com 74AC373 • 74ACT373 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide Body Package Number M20B www.fairchildsemi.com 6 74AC373 • 74ACT373 Physical Dimensio