5 Watt Surmetic 40 Zener Voltage Refulators

1N5333B Series Preferred Device 5 Watt Surmetict 40 Zener Voltage Regulators This is a complete series of 5 Watt Zener diodes with tight limits and better operating characteristics that reflect the superior capabilities of silicon−oxide passivated junctions. All this in an axial lead, transfer−molded plastic package that offers protection in all common environmental conditions. Features http://onsemi.com Cathode Anode • Zener www.DataSheet4U.com Voltage Range − 3.3 V to 200 V • ESD Rating of Class 3 (>16 kV) per Human Body Model • Surge Rating of up to 180 W @ 8.3 ms • Maximum Limits Guaranteed on up to Six Electrical Parameters • These devices are manufactured with a Pb−Free external lead finish only* Mechanical Characteristics CASE: Void free, transfer−molded, thermosetting plastic FINISH: All external surfaces are corrosion resistant and leads are AXIAL LEAD CASE 17 PLASTIC readily solderable MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES: 230°C, 1/16 in. from the case for 10 seconds POLARITY: Cathode indicated by polarity band MOUNTING POSITION: Any MAXIMUM RATINGS Rating Max. Steady State Power Dissipation @ TL = 75°C, Lead Length = 3/8 in Derate above 75°C Operating and Storage Temperature Range Symbol PD Value 5 40 TJ, Tstg −65 to +200 Unit W mW/°C °C MARKING DIAGRAM L 1N 53xxB YWW L 1N53xxB Y WW = Assembly Location = Device Code = (See Table Next Page) = Year = Work Week Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. ORDERING INFORMATION Device 1N53xxB 1N53xxBRL 1N53xxBTA* Package Axial Lead Axial Lead Axial Lead Shipping† 1000 Units/Box 4000/Tape & Reel 2000/Ammo Pack *1N5361B Not Available in 2000/Ammo Pack †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Preferred devices are recommended choices for future use and best overall value. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2004 1 December, 2004 − Rev. 4 Publication Order Number: 1N5333B/D 1N5333B Series ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types) Symbol VZ IZT ZZT IZK ZZK IR VR IF VF www.DataSheet4U.com IR DVZ IZM Parameter Reverse Zener Voltage @ IZT Reverse Current Maximum Zener Impedance @ IZT Reverse Current Maximum Zener Impedance @ IZK Reverse Leakage Current @ VR Breakdown Voltage Forward Current Forward Voltage @ IF Maximum Surge Current @ TA = 25°C Reverse Zener Voltage Change Maximum DC Zener Current VZ VR IR VF IZT V IF I Zener Voltage Regulator http://onsemi.com 2 1N5333B Series ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types) Zener Voltage (Note 2) Device (Note 1) Device Marking VZ (Volts) Min Nom Max @ IZT mA Zener Impedance (Note 2) ZZT @ IZT W ZZK @ IZK W IZK mA Leakage Current IR @ VR mA Max Volts IR (Note 3) A DVZ (Note 4) Volts IZM (Note 5) mA 1N5333B 1N5334B 1N5335B 1N5336B 1N5337B 1N5338B 1N5339B 1N5340B 1N5341B www.DataSheet4U.com 1N5342B 1N5343B 1N5344B 1N5345B 1N5346B 1N5347B 1N5348B 1N5349B 1N5350B 1N5351B 1N5352B 1N5333B 1N5334B 1N5335B 1N5336B 1N5337B 1N5338B 1N5339B 1N5340B 1N5341B 1N5342B 1N5343B 1N5344B 1N5345B 1N5346B 1N5347B 1N5348B 1N5349B 1N5350B 1N5351B 1N5352B 3.14 3.42 3.71 4.09 4.47 4.85 5.32 5.70 5.89 6.46 7.13 7.79 8.27 8.65 9.50 10.45 11.4 12.35 13.3 14.25 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.0 6.2 6.8 7.5 8.2 8.7 9.1 10 11 12 13 14 15 3.47 3.78 4.10 4.52 4.94 5.36 5.88 6.30 6.51 7.14 7.88 8.61 9.14 9.56 10.5 11.55 12.6 13.65 14.7 15.75 380 350 320 290 260 240 220 200 200 175 175 150 150 150 125 125 100 100 100 75 3 2.5 2 2 2 1.5 1 1 1 1 1.5 1.5 2 2 2 2.5 2.5 2.5 2.5 2.5 400 500 500 500 450 400 400 300 200 200 200 200 200 150 125 125 125 100 75 75 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 300 150 50 10 5 1 1 1 1 10 10 10 10 7.5 5 5 2 1 1 1 1 1 1 1 1 1 2 3 3 5.2 5.7 6.2 6.6 6.9 7.6 8.4 9.1 9.9 10.6 11.5 20 18.7 17.6 16.4 15.3 14.4 13.4 12.7 12.4 11.5 10.7 10 9.5 9.2 8.6 8.0 7.5 7.0 6.7 6.3 0.85 0.8 0.54 0.49 0.44 0.39 0.25 0.19 0.1 0.15 0.15 0.2 0.2 0.22 0.22 0.25 0.25 0.25 0.25 0.25 1440 1320 1220 1100 1010 930 865 790 765 700 630 580 545 520 475 430 395 365 340 315 1N5353B 1N5354B 1N5355B 1N5356B 1N5357B 1N5358B 1N5359B 1N5360B 1N5361B* 1N5362B 1N5353B 1N5354B 1N5355B 1N5356B 1N5357B 1N5358B 1N5359B 1N5360B 1N5361B 1N5362B 15.2 16.15 17.1 18.05 19 20.9 22.8 23.75 25.65 26.6 16 17 18 19 20 22 24 25 27 28 16.8 17.85 18.9 19.95 21 23.1 25.2 26.25 28.35 29.4 75 70 65 65 65 50 50 50 50 50 2.5 2.5 2.5 3 3 3.5 3.5 4 5 6 75 75 75 75 75 75 100 110 120 130 1 1 1 1 1 1 1 1 1 1 1 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 12.2 12.9 13.7 14.4 15.2 16.7 18.2 19 20.6 21.2 6.0 5.8 5.5 5.3 5.1 4.7 4.4 4.3 4.1 3.9 0.3 0.35 0.4 0.4 0.4 0.45 0.55 0.55 0.6 0.6 295 280 264 250 237 216 198 190 176 170 Devices listed in bold, italic are ON Semiconductor Preferred devices. Preferred devices are recommended choices for future use and best overall value. 1. TOLERANCE AND TYPE NUMBER DESIGNATION The JEDEC type numbers shown indicate a tolerance of ±5%. 2. ZENER VOLTAGE (VZ) and IMPEDANCE (IZT and IZK) Test conditions for zener voltage and impedance are as follows: IZ is applied 40 ±10 ms prior to reading. Mounting contacts are located 3/8″ to 1/2″ from the inside edge of mounting clips to the body of the diode (TA = 25°C +8°C, −2°C). 3. SURGE CURRENT (IR) Surge current is specified as the maximum allowable peak, non−recurrent square−wave current with a pulse width, PW, of 8.3 ms. The data given in Figure 5 may be used to find the maximum surge current for a square wave of any pulse width between 1 ms and 1000 ms by plotting the applicable points on logarithmic paper. Examples of this, using the 3.3 V and 200 V zener are shown in Figure 6. Mounting contact located as specified in Note 2 (TA = 25°C +8°C, −2°C). 4. VOLTAGE REGULATION (DVZ) The conditions for voltage regulation are as follows: VZ measurements are made at 10% and then at 50% of the IZ max value listed in the electrical characteristics table. The test current time duration for each VZ measurement is 40 ±10 ms. Mounting contact located as specified in Note 2 (TA = 25°C +8°C, −2°C). 5. MAXIMUM REGULATOR CURRENT (IZM) The maximum current shown is based on the maximum voltage of a 5% type unit, therefore, it applies only to the B−suffix device. The actual IZM for any device may not exceed the value of 5 watts divided by the actual VZ of the device. TL = 75°C at 3/8″ maximum from the device body. *Not Available in the 2000/Ammo Pack. http://onsemi.com 3 1N5333B Series ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types) Zener Voltage (Note 7) Device (Note 6) 1N5363B 1N5364B 1N5365B 1N5366B 1N5367B Device Marking 1N5363B 1N5364B 1N5365B 1N5366B 1N5367B VZ (Volts) Min 28.5 31.35 34.2 37.05 40.85 Nom 30 33 36 39 43 Max 31.5 34.65 37.8 40.95 45.15 @ IZT mA 40 40 30 30 30 Zener Impedance (Note 7) ZZT @ IZT W 8 10 11 14 20 ZZK @ IZK W 140 150 160 170 190 IZK mA 1 1 1 1 1 Leakage Current IR @ VR mA Max 0.5 0.5 0.5 0.5 0.5 Volts 22.8 25.1 27.4 29.7 32.7 IR (Note 8) A 3.7 3.5 3.5 3.1 2.8 DVZ (Note 9) Volts 0.6 0.6 0.65 0.65 0.7 IZM (Note 10) mA 158 144 132 122 110 1N5368B 1N5369B 1N5370B 1N5371B www.DataSheet4U.com 1N5372B 1N5373B 1N5374B 1N5375B 1N5376B 1N5377B 1N5378B 1N5379B 1N5380B 1N5381B 1N5382B 1N5368B 1N5369B 1N5370B 1N5371B 1N5372B 1N5373B 1N5374B 1N5375B 1N5376B 1N5377B 1N5378B 1N5379B 1N5380B 1N5381B 1N5382B 44.65 48.45 53.2 57 58.9 64.6 71.25 77.9 82.65 86.45 95 104.5 114 123.5 133 47 51 56 60 62 68 75 82 87 91 100 110 120 130 140 49.35 53.55 58.8 63 65.1 71.4 78.75 86.1 91.35 95.55 105 115.5 126 136.5 147 25 25 20 20 20 20 20 15 15 15 12 12 10 10 8 25 27 35 40 42 44 45 65 75 75 90 125 170 190 230 210 230 280 350 400 500 620 720 760 760 800 1000 1150 1250 1500 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 35.8 38.8 42.6 45.5 47.1 51.7 56 62.2 66 69.2 76 83.6 91.2 98.8 106 2.7 2.5 2.3 2.2 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.2 0.8 0.9 1.0 1.2 1.35 1.52 1.6 1.8 2.0 2.2 2.5 2.5 2.5 2.5 2.5 100 93 86 79 76 70 63 58 54.5 52.5 47.5 43 39.5 36.6 34 1N5383B 1N5384B 1N5385B 1N5386B 1N5387B 1N5388B 1N5383B 1N5384B 1N5385B 1N5386B 1N5387B 1N5388B 142.5 152 161.5 171 180.5 190 150 160 170 180 190 200 157.5 168 178.5 189 199.5 210 8 8 8 5 5 5 330 350 380 430 450 480 1500 1650 1750 1750 1850 1850 1 1 1 1 1 1 0.5 0.5 0.5 0.5 0.5 0.5 114 122 129 137 144 152 1.1 1.1 1.0 1.0 0.9 0.9 3.0 3.0 3.0 4.0 5.0 5.0 31.6 29.4 28 26.4 25 23.6 Devices listed in bold, italic are ON Semiconductor Preferred devices. Preferred devices are recommended choices for future use and best overall value. 6. TOLERANCE AND TYPE NUMBER DESIGNATION The JEDEC type numbers shown indicate a tolerance of ±5%. 7. ZENER VOLTAGE (VZ) and IMPEDANCE (IZT and IZK) Test conditions for zener voltage and impedance are as follows: IZ is applied 40 ±10 ms prior to reading. Mounting contacts are located 3/8″ to 1/2″ from the inside edge of mounting clips to the body of the diode (TA = 25°C +8°C, −2°C). 8. SURGE CURRENT (IR) Surge current is specified as the maximum allowable peak, non−recurrent square−wave current with a pulse width, PW, of 8.3 ms. The data given in Figure 5 may be used to find the maximum surge current for a square wave of any pulse width between 1 ms and 1000 ms by