http://www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf


International Rectifier
International Rectifier

IR2113S Datasheet

HIGH AND LOW SIDE DRIVER


IR2113S Datasheet Preview


Data Sheet No. PD60147 Rev.T
IR2110(S)/IR2113(S) &(PbF)
HIGH AND LOW SIDE DRIVER
Features
Floating channel designed for bootstrap operation
Fully operational to +500V or +600V
Tolerant to negative transient voltage
dV/dt immune
Gate drive supply range from 10 to 20V
Undervoltage lockout for both channels
3.3V logic compatible
Separate logic supply range from 3.3V to 20V
Logic and power ground ±5V offset
CMOS Schmitt-triggered inputs with pull-down
Cycle by cycle edge-triggered shutdown logic
Matched propagation delay for both channels
Outputs in phase with inputs
Also available LEAD-FREE
Product Summary
VOFFSET (IR2110) 500V max.
(IR2113) 600V max.
IO+/-
2A / 2A
VOUT
10 - 20V
ton/off (typ.)
120 & 94 ns
Delay Matching (IR2110) 10 ns max.
(IR2113) 20ns max.
Packages
Description
The IR2110/IR2113 are high voltage, high speed power MOSFET and
IGBT drivers with independent high and low side referenced output chan-
nels. Proprietary HVIC and latch immune CMOS technologies enable
ruggedized monolithic construction. Logic inputs are compatible with
standard CMOS or LSTTL output, down to 3.3V logic. The output
drivers feature a high pulse current buffer stage designed for minimum
14-Lead PDIP
IR2110/IR2113
16-Lead SOIC
IR2110S/IR2113S
(Also available
LEAD-FREE (PbF))
driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The
floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which
operates up to 500 or 600 volts.
Typical Connection
up to 500V or 600V
HO
VDD
VDD
VB
HIN HIN VS
SD SD
LIN LIN VCC
VSS VSS COM
VCC LO
(Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical
connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout.
www.irf.com
TO
LOAD
1
Page 1

IR2110(S)/IR2113(S) &(PbF)
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage param-
eters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured
under board mounted and still air conditions. Additional information is shown in Figures 28 through 35.
Symbol
Definition
Min.
Max. Units
VB High side floating supply voltage (IR2110)
(IR2113)
-0.3 525
-0.3 625
VS
VHO
VCC
VLO
VDD
VSS
VIN
dVs/dt
PD
High side floating supply offset voltage
High side floating output voltage
Low side fixed supply voltage
Low side output voltage
Logic supply voltage
Logic supply offset voltage
Logic input voltage (HIN, LIN & SD)
Allowable offset supply voltage transient (figure 2)
Package power dissipation @ TA +25°C (14 lead DIP)
(16 lead SOIC)
VB - 25
VS - 0.3
-0.3
-0.3
-0.3
VCC - 25
VSS - 0.3
VB + 0.3
VB + 0.3
25
VCC + 0.3
VSS + 25
VCC + 0.3
VDD + 0.3
50
1.6
1.25
V
V/ns
W
RTHJA
Thermal resistance, junction to ambient
(14 lead DIP)
(16 lead SOIC)
75
°C/W
100
TJ Junction temperature
TS Storage temperature
TL Lead temperature (soldering, 10 seconds)
— 150
-55 150 °C
— 300
Recommended Operating Conditions
The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the
recommended conditions. The VS and VSS offset ratings are tested with all supplies biased at 15V differential. Typical
ratings at other bias conditions are shown in figures 36 and 37.
Symbol
Definition
Min.
Max. Units
VB High side floating supply absolute voltage
VS High side floating supply offset voltage (IR2110)
(IR2113)
VS + 10
Note 1
Note 1
VS + 20
500
600
VHO
High side floating output voltage
VS VB
VCC
Low side fixed supply voltage
10 20 V
VLO Low side output voltage
0 VCC
VDD
Logic supply voltage
VSS + 3
VSS + 20
VSS Logic supply offset voltage
-5 (Note 2)
5
VIN Logic input voltage (HIN, LIN & SD)
VSS
VDD
TA Ambient temperature
-40 125 °C
Note 1: Logic operational for VS of -4 to +500V. Logic state held for VS of -4V to -VBS. (Please refer to the Design Tip
DT97-3 for more details).
Note 2: When VDD < 5V, the minimum VSS offset is limited to -VDD.
2 www.irf.com
Page 2

IR2110(S)/IR2113(S) &(PbF)
Dynamic Electrical Characteristics
VBIAS (VCC, VBS, VDD) = 15V, CL = 1000 pF, TA = 25°C and VSS = COM unless otherwise specified. The dynamic
electrical characteristics are measured using the test circuit shown in Figure 3.
Symbol
ton
toff
tsd
tr
tf
MT
Definition
Turn-on propagation delay
Turn-off propagation delay
Shutdown propagation delay
Turn-on rise time
Turn-off fall time
Delay matching, HS & LS
turn-on/off
(IR2110)
(IR2113)
Figure Min.
7—
8—
9—
10 —
11 —
——
——
Typ. Max. Units Test Conditions
120 150
94 125
VS = 0V
VS = 500V/600V
110 140 ns VS = 500V/600V
25 35
17 25
— 10
— 20
Static Electrical Characteristics
VBIAS (VCC, VBS, VDD) = 15V, TA = 25°C and VSS = COM unless otherwise specified. The VIN, VTH and IIN parameters
are referenced to VSS and are applicable to all three logic input leads: HIN, LIN and SD. The VO and IO parameters are
referenced to COM and are applicable to the respective output leads: HO or LO.
Symbol
VIH
VIL
VOH
VOL
ILK
IQBS
IQCC
IQDD
IIN+
IIN-
VBSUV+
VBSUV-
VCCUV+
VCCUV-
IO+
IO-
Definition
Logic “1” input voltage
Logic “0” input voltage
High level output voltage, VBIAS - VO
Low level output voltage, VO
Offset supply leakage current
Quiescent VBS supply current
Quiescent VCC supply current
Quiescent VDD supply current
Logic “1” input bias current
Logic “0” input bias current
VBS supply undervoltage positive going
threshold
VBS supply undervoltage negative going
threshold
VCC supply undervoltage positive going
threshold
VCC supply undervoltage negative going
threshold
Output high short circuit pulsed current
Output low short circuit pulsed current
Figure Min.
12 9.5
13 —
14 —
15 —
16 —
17 —
18 —
19 —
20 —
21 —
22 7.5
Typ. Max. Units Test Conditions
——
— 6.0
— 1.2
— 0.1
— 50
125 230
180 340
15 30
20 40
— 1.0
8.6 9.7
V IO = 0A
IO = 0A
VB=VS = 500V/600V
VIN = 0V or VDD
µA VIN = 0V or VDD
VIN = 0V or VDD
VIN = VDD
VIN = 0V
23 7.0 8.2 9.4
24 7.4 8.5 9.6
V
25 7.0 8.2 9.4
26 2.0 2.5 —
27 2.0 2.5 —
VO = 0V, VIN = VDD
PW 10 µs
A VO = 15V, VIN = 0V
PW 10 µs
www.irf.com
3
Page 3
Part Number IR2113S
Manufactur International Rectifier
Description HIGH AND LOW SIDE DRIVER
Total Page 16 Pages
PDF Download
IR2113S datasheet
Download PDF File
IR2113S datasheet
View Html for PC & Mobile


Related Datasheet

IR2113 , IR2113C , IR2113PBF , IR2113S , IR2113SPBF ,

site map

webmaste! click here

contact us

Buy Components