http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf





TOKO
TOKO

TK11132S Datasheet Preview

TK11132S Datasheet

VOLTAGE REGULATOR WITH ON/OFF SWITCH

No Preview Available !

TK11132S pdf
TK111xxS
VOLTAGE REGULATOR WITH ON/OFF SWITCH
FEATURES
s High Voltage Precision at ± 2.0% or ± 60 mV
s Active High On/Off Control
s Very Low Dropout Voltage (85 mV at 30 mA)
s Very Low Noise
s Miniature Package (SOT-23-5)
s Internal Thermal Shutdown
s Short Circuit Protection
s Excellent Ripple Rejection (70 dB @ 1 kHz)
s Reverse Bias Protection
DESCRIPTION
APPLICATIONS
s Battery Powered Systems
s Cellular Telephones
s Pagers
s Personal Communications Equipment
s Portable Instrumentation
s Portable Consumer Equipment
s Radio Control Systems
s Toys
The TK111xxS is a low dropout linear regulator with a built-
in electronic switch. The internal switch can be controlled
by TTL or CMOS logic levels. The device is in the “on” state
when the control pin is pulled to a logic high level. An
external capacitor can be connected to the noise bypass
pin to lower the output noise level to 30 µVrms.
An internal PNP pass transistor is used to achieve a low
dropout voltage of 85 mV (typ.) at 30 mA load current. The
TK111xxS has a very low quiescent current of 140 µA
(typ.) at no load . The standby current is 100 nA maximum.
The internal thermal shut down circuitry limits the junction
temperature to below 150 °C. The load current is internally
monitored and the device will shut down in the presence of
a short circuit or overcurrent condition at the output.
The TK111xxS is available in a miniature SOT-23-5 surface
mount package.
ORDERING INFORMATION
TK111 S L
Voltage Code
Tape/Reel Code
Temp. Code
Package Code
VOLTAGE CODE
20 = 2.0 V
32 = 3.2 V
21 = 2.1 V
33 = 3.3 V
22 = 2.2 V
34 = 3.4 V
23 = 2.3 V
35 = 3.5 V
24 = 2.4 V
36 = 3.6 V
25 = 2.5 V
37 = 3.7 V
27 = 2.7 V
38 = 3.8 V
28 = 2.8 V
39 = 3.9 V
29 = 2.9 V
40 = 4.0 V
30 = 3.0 V
41 = 4.1 V
31 = 3.1 V
42 = 4.2 V
43 = 4.3 V
44 = 4.4 V
45 = 4.5 V
46 = 4.6 V
47 = 4.7 V
48 = 4.8 V
49 = 4.9 V
50 = 5.0 V
Note 1: 2.0 to 2.3 V
available in C
temperature code
(-30 to +80 °C) only
TAPE/REEL CODE
L: Tape Left
PACKAGE CODE
S: SOT-23-5
TEMP. CODE
C: -30 to +80 °C
I: -40 to +85 °C
20P
VIN 5
CONTROL
March 1999 TOKO, Inc.
TK111xxS
CONTROL
GND
NOISE BYPASS
BLOCK DIAGRAM
THERMAL
PROTECTION
BANDGAP
REFERENCE
NOISE
BYPASS
VIN
VOUT
VOUT
GND
Page 1



TOKO
TOKO

TK11132S Datasheet Preview

TK11132S Datasheet

VOLTAGE REGULATOR WITH ON/OFF SWITCH

No Preview Available !

TK11132S pdf
TK111xxS
ABSOLUTE MAXIMUM RATINGS TK111xxSCL
Supply Voltage ......................................................... 16 V
Control Terminal Voltage ......................................... 12 V
Noise Bypass Terminal Voltage ................................. 5 V
Power Dissipation (Note 1) ................................ 500 mW
Reverse Bias ............................................................ 10 V
Storage Temperature Range ................... -55 to +150 °C
Operating Temperature Range ...................-30 to +80 °C
Operating Voltage Range ............................... 1.8 to 12 V
Junction Temperature ........................................... 150 °C
Lead Soldering Temperature (10 s) ...................... 235 °C
TK111xxSCL ELECTRICAL CHARACTERISTICS
Test conditions: VIN = VOUT(TYP) + 1 V, TA = 25 °C, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNITS
IQ
ISTBY
VOUT
Line Reg
Load Reg
VDROP
IOUT
IOUT(PULSE)
Quiescent Current
Standby Current
Output Voltage
Line Regulation
Load Regulation
Dropout Voltage
Continuous Output Current
Pulse Output Current
IOUT = 0 mA, Excluding ICONT
VIN = 6 V, Output OFF, VCONT 0.15 V
IOUT = 10 mA, VIN = VOUT(TYP) + 1 V
VIN = VOUT(TYP) + 1 V to
VOUT(TYP) + 6 V, (Note 2)
IOUT = 1 to 60 mA, (Note 2)
IOUT = 1 to 100 mA, (Note 2)
IOUT = 60 mA, (Note 2)
(Note 2)
5 ms pulse, 12.5 % duty cycle, (Note
2)
140 200
0.1
See Table 1
0.8 18
8 30
14 55
120 200
100
130
µA
µA
V
mV
mV
mV
mV
mA
mA
RR Ripple Rejection
f = 1 kHz, CL = 4.7 µF,
CN = 0.1 µF, VIN = VOUT(TYP) + 2 V, VR =
200 mVrms, IOUT = 10 mA, (Notes
3,4)
70
dB
400 Hz f 80 kHz, CL = 4.7 µF,
VNO
Output Noise Voltage
CN = 0.01 µF, VIN = VOUT(TYP) + 2 V,
IOUT = 10 mA, (Notes 3,4)
Vref
Noise Bypass Terminal
Voltage
VOUT /T Temperature Coefficient
IOUT = 10 mA
CONTROL TERMINAL SPECIFICATIONS
30
1.25
25
µVrms
V
ppm/° C
ICONT
Control Current
VCONT = 1.8 V, Output ON
1.2
VCONT(ON) Control Voltage ON
Output ON
1.5
VCONT(OFF) Control Voltage OFF
Output OFF
Note 1: Power dissipation is 500 mW when mounted as recommended. Derate at 4.0 mW/°C for operation above 25 °C.
Note 2: Refer to “Definition of Terms.”
Note 3: Ripple rejection and noise voltage are affected by the value and characteristics of the capacitor used.
Note 4: Output noise voltage can be reduced by connecting a capacitor to the noise bypass terminal.
Gen. Note: Parameters with min. or max. values are 100% tested at TA = 25 °C.
Gen. Note: Exceeding the “Absolute Maximum Ratings” can damage the device.
4
0.35
µA
V
V
Page 2
March 1999 TOKO, Inc.


Part Number TK11132S
Description VOLTAGE REGULATOR WITH ON/OFF SWITCH
Maker TOKO
Total Page 16 Pages
PDF Download
TK11132S pdf
Download PDF File
[partsNo] view html
View PDF for Mobile






Related Datasheet

1 TK11132M VOLTAGE REGULATOR WITH ON/OFF SWITCH TOKO
TOKO
TK11132M pdf
2 TK11132S VOLTAGE REGULATOR WITH ON/OFF SWITCH TOKO
TOKO
TK11132S pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components