http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf





TEMIC Semiconductors
TEMIC Semiconductors

U2043B Datasheet Preview

U2043B Datasheet

Flasher/ 30-mohm Shunt/ Pilot Lamp to GND or V Batt

No Preview Available !

U2043B pdf
U2043B
WFlasher, 30-m Shunt, Pilot Lamp to GND or VBatt
Description
The integrated circuit U2043B is used in relay controlled
automotive flashers where a high EMC level is required.
A lamp outage is indicated by frequency doubling during
hazard mode as well as direction mode. Pilot lamp can be
connected either to VBatt or GND.
Features
D Temperature and voltage compensated frequency
D Warning indication of lamp failure by means of
frequency doubling
wD Minimum lamp load for flasher operation 10 W
D Relay output with high current carrying capacity and
low saturation voltage
D Low susceptibility to EMI
Ordering Information
Extended Type Number
U2043B
U2043B–FP
Package
DIP8
SO8
Remarks
Block Diagram
C1
4
6
Measuring comparator
K1 V6–81 mV
2
7
WR3 30 m
Shunt
+ VS
+ 49
Pilot lamp 5 W
Pulse
R1 generator
3.8 k W
5 K3 V6–5 V
49 a–Comparator
3
Relay
8 R2
3.3 k W
23 V
1 R1
IC Ground
100 W
13283
GND
– 31
Figure 1.
49 a
5 W 21 W 21 W 21 W 21 W 5 W
Indicator lamps
Pilot lamps
TELEFUNKEN Semiconductors
Rev. A2, 25-Feb-97
1 (6)



TEMIC Semiconductors
TEMIC Semiconductors

U2043B Datasheet Preview

U2043B Datasheet

Flasher/ 30-mohm Shunt/ Pilot Lamp to GND or V Batt

No Preview Available !

U2043B pdf
U2043B
Pin Description
Pin Symbol
Function
1 GND IC ground
2 VS Supply voltage VS
3 REL Relay driver
4 OSC C1 oscillator
5 OSC R1 oscillator
6 VS Supply voltage VS
7 LD Lamp failure detection
8 SI Start input (49a)
GND 1
8 SI
Vs 2
REL 3
7 LD
U2043B
6 Vs
OSC 4
5 OSC
Figure 2. Pinning
12749
Functional Description
Pin 1, GND
The integrated circuit is protected against damage via
resistor R4 to ground (–31) in the case of battery reversal.
An integrated protection circuit together with external
resistances R2 and R4 limits the current pulses in the IC.
Pin 2, Supply voltage, VS - Power
The arrangement of the supply connections to Pin 2 must
be such as ensure that, on the connection printed circuit
board (PCB), the resistance of VS to Pin 6 is lower than
that to Pin 2.
Pin 3, Relay control output (driver)
The relay control output is a high-side driver with a low
saturation voltage and capable to drive a typical automo-
Wtive relay with a minimum coil resistance of 60 .
Pin 4 and 5 Oscillator
Flashing frequency, f1, is determined by the R1C1 compo-
nents as follows (see figure 1):
where
[f1
R1
1
C1
1.5 Hz
C1
+R1
47 mF
6.8 kW to 510 kW
In the case of a lamp outage (see Pin 7) the oscillator
[frequency is switched to the lamp outage frequency f2
with f2 2.2 f1.
Duty cycle in normal flashing mode: 50%
Duty cycle in lamp outage mode: 40% (bright phase)
Pin 6, Supply voltage, Sense
For accurate monitoring via the shunt resistor, a mini-
mized layer resistance from point VS / shunt to Pin 6 is
recommended.
Pin 7, Lamp outage detection
The lamp current is monitored via an external shunt
resistor R3 and an internal comparator K1 with its
reference voltage of typ. 81 mV (VS = 12 V). The outage
of one lamp out of two lamps is detected according to the
following calculation:
Nominal current of 1 lamp: 21 W / (VS = 12 V):
Ilamp = 1.75 A
Nominal current of 2 lamps: 2 x 21 W / (VS = 12 V):
Ilamp = 3.5 A.
[The detection threshold is recommended to be set in the
middle of the current range: Ioutage 2.7 A
Thus the shunt resistor is calculated as:
WR3 = VT (K1) / Ioutage
R3 = 81 mV/2.7 A = 30 m .
Comparator K1‘s reference voltage is matched to the
characteristics of filament lamps (see “control signal
threshold” in the data part).
The combination of shunt resistor and resistance of wire
harness prevents Pin 7 from a too high voltage in the case
of shortet lamps.
Pin 8, Start input
Start condition for flashing: the voltage at Pin 8 has to be
below less than VS – 5 V (flasher switch closed).
u WHumidity and dirt may decrease the resistance between
49 a and GND. If this leakage resistance is 5 k the IC
is still kept in its off-condition. In this case the voltage at
Pin 8 is greater than VS – 5 V.
During the bright phase the voltage at Pin 8 is above the
K2 threshold, during the dark phase it is below the K3
threshold. For proper start conditions a minimum lamp
wattage of 10 W is required.
2 (6) TELEFUNKEN Semiconductors
Rev. A2, 25-Feb-97


Part Number U2043B
Description Flasher/ 30-mohm Shunt/ Pilot Lamp to GND or V Batt
Maker TEMIC Semiconductors
Total Page 6 Pages
PDF Download
U2043B pdf
Download PDF File
U2043B pdf
View for Mobile






Related Datasheet

1 U2043B Flasher/ 30-mohm Shunt/ Pilot Lamp to GND or V Batt TEMIC Semiconductors
TEMIC Semiconductors
U2043B pdf
2 U2043B Pilot Lamp to GND or VBatt ATMEL Corporation
ATMEL Corporation
U2043B pdf
3 U2043B-FP Flasher/ 30-mohm Shunt/ Pilot Lamp to GND or V Batt TEMIC Semiconductors
TEMIC Semiconductors
U2043B-FP pdf




Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components