http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




Motorola Electronic Components Datasheet

MC54HC534A Datasheet

OCTAL 3-STATE INVERTING D FLIP-FLOP

No Preview Available !

MC54HC534A pdf
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Octal 3-State
Inverting D Flip-Flop
High–Performance Silicon–Gate CMOS
The MC54/74HC534A is identical in pinout to the LS534. The device
inputs are compatible with standard CMOS outputs; with pullup resistors,
they are compatible with LSTTL outputs.
Data meeting the setup time is clocked, in inverted form, to the outputs
with the rising edge of the Clock. The Output Enable input does not affect the
states of the flip–flops, but when Output Enable is high, the outputs are
forced to the high impedance state. Thus, data may be stored even when the
outputs are not enabled.
The HC534A is identical in function to the HC564 which has the data
inputs on the opposite side of the package from the outputs to facilitate PC
board layout.
This device is similar in function to the HC374A, which has noninverting
outputs.
Output Drive Capability: 15 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS and TTL
Operating Voltage Range: 2.0 to 6.0 V
Low Input Current: 1.0 µA
High Noise Immunity Characteristic of CMOS Devices
In Compliance with the Requirements Defined by JEDEC Standard
No. 7A
Chip Complexity: 282 FETs or 68.5 Equivalent Gates
LOGIC DIAGRAM
DATA
INPUTS
D0 3
D1 4
D2 7
D3 8
D4 13
D5 14
D6 17
D7 18
CLOCK 11
2 Q0
5 Q1
6 Q2
9 Q3
12 Q4
15 Q5
16 Q6
19 Q7
INVERTING
OUTPUTS
OUTPUT ENABLE 1
PIN 20 = VCC
PIN 10 = GND
MC54/74HC534A
20
1
J SUFFIX
CERAMIC PACKAGE
CASE 732–03
20
1
20
1
N SUFFIX
PLASTIC PACKAGE
CASE 738–03
DW SUFFIX
SOIC PACKAGE
CASE 751D–04
ORDERING INFORMATION
MC54HCXXXAJ
MC74HCXXXAN
MC74HCXXXADW
Ceramic
Plastic
SOIC
PIN ASSIGNMENT
OUTPUT
ENABLE
Q0
1
2
20 VCC
19 Q7
D0 3
18 D7
D1 4
17 D6
Q1 5
16 Q6
Q2 6
15 Q5
D2 7
14 D5
D3 8
13 D4
Q3 9
12 Q4
GND 10
11 CLOCK
FUNCTION TABLE
Inputs
Output
Output
Enable Clock
D
Q
L
L
L L,H,
HX
HL
LH
X No Change
XZ
X = Don’t Care
Z = High Impedance
10/95
© Motorola, Inc. 1995
3–1 REV 6


Motorola Electronic Components Datasheet

MC54HC534A Datasheet

OCTAL 3-STATE INVERTING D FLIP-FLOP

No Preview Available !

MC54HC534A pdf
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎMC54/74HC534A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎMAXIMUM RATINGS*
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
Parameter
Value
Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVCC
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVin
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVout
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎIin
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎIout
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎICC
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎPD
DC Supply Voltage (Referenced to GND)
– 0.5 to + 7.0
V
DC Input Voltage (Referenced to GND)
DC Output Voltage (Referenced to GND)
DC Input Current, per Pin
– 1.5 to VCC + 1.5
– 0.5 to VCC + 0.5
± 20
V
V
mA
DC Output Current, per Pin
± 35 mA
DC Supply Current, VCC and GND Pins
Power Dissipation in Still Air, Plastic or Ceramic DIP†
SOIC Package†
± 75
750
500
mA
mW
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTstg Storage Temperature
– 65 to + 150
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTL Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP or SOIC Package)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ(Ceramic DIP)
260
300
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ* Maximum Ratings are those values beyond which damage to the device may occur.
_C
_C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high–impedance cir-
cuit. For proper operation, Vin and
v vVout should be constrained to the
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
Functional operation should be restricted to the Recommended Operating Conditions.
†Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C
Ceramic DIP: – 10 mW/_C from 100_ to 125_C
SOIC Package: – 7 mW/_C from 65_ to 125_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎFor high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎRECOMMENDED OPERATING CONDITIONS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
Parameter
Min Max Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVCC DC Supply Voltage (Referenced to GND)
2.0 6.0 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVin, Vout DC Input Voltage, Output Voltage (Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTA Operating Temperature, All Package Types
0 VCC
– 55 + 125
V
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎtr, tf Input Rise and Fall Time
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ(Figure 1)
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
0
0
0
1000
500
400
ns
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎDC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVIH
Parameter
Minimum High–Level Input
Voltage
Test Conditions
vVout = 0.1 V or VCC – 0.1 V
|Iout| 20 µA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVIL MaximumLow–LevelInput
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVoltage
vVout = 0.1 V or VCC – 0.1 V
|Iout| 20 µA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVOH
Minimum High–Level Output
Voltage
vVin = VIH or VIL
|Iout| 20 µA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVOL
Maximum Low–Level Output
Voltage
Vin = VIH or VIL
v|Iout| 6.0 mA
v|Iout| 7.8 mA
vVin = VIH or VIL
|Iout| 20 µA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVin = VIH or VIL
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎv|Iout| 6.0mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎv|Iout| 7.8mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎIin Maximum Input Leakage Current Vin= VCC or GND
VCC
V
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
Guaranteed Limit
v v– 55 to
25_C
85_C
125_C
1.5 1.5 1.5
3.15 3.15 3.15
4.2 4.2 4.2
0.5 0.5 0.5
1.35 1.35 1.35
1.8 1.8 1.8
1.9 1.9 1.9
4.4 4.4 4.4
5.9 5.9 5.9
4.5 3.98
6.0 5.48
2.0 0.1
4.5 0.1
6.0 0.1
3.84
5.34
0.1
0.1
0.1
3.7
5.2
0.1
0.1
0.1
4.5 0.26
6.0 0.26
0.33
0.33
0.4
0.4
6.0 ± 0.1 ± 1.0 ± 1.0
Unit
V
V
V
V
V
V
µA
MOTOROLA
3–2 High–Speed CMOS Logic Data
DL129 — Rev 6


Part Number MC54HC534A
Description OCTAL 3-STATE INVERTING D FLIP-FLOP
Maker Motorola
Total Page 6 Pages
PDF Download
MC54HC534A pdf
Download PDF File
[partsNo] view html
View PDF for Mobile






Related Datasheet

1 MC54HC534A OCTAL 3-STATE INVERTING D FLIP-FLOP Motorola
Motorola
MC54HC534A pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components