http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




IBM Microelectronics
IBM Microelectronics

IBM42F10SNNAA20 Datasheet Preview

IBM42F10SNNAA20 Datasheet

(IBM42F10SNNAA20 / IBM42F12SNNAA20) Small Form Factor Transceiver

No Preview Available !

IBM42F10SNNAA20 pdf
www.DataSheet4U.com
IBM42F10SNNAA20
IBM42F12SNNAA20
1063/1250MBd Small Form Factor Transceiver with Signal Detect
Features
• International Class 1 laser safety certified
• 1063Mb/s to 1250Mb/s data rates
• (ANSI) Fibre Channel compliant [1]
• (IEEE 802.3z/d2) Gigabit Ethernet compliant [2]
• Short wavelength (SW) (distance 550m)
• Gigabit electrical serial interface
• Serial electrical light conversion
• UL & CSA approved
• LVTTL Signal-Detect Output
• Single +3.3V Power Supply
• Low bit error rate (< 10-12)
• High reliability
- AFR < 0.01 %/khr @50 C
Applications
• Gigabit Fibre Channel
• Gigabit Ethernet
• Client/Server environments
• Distributed multi-processing
• Fault tolerant applications
• Visualization, real-time video, collaboration
• Channel extenders, data storage, archiving
• Data acquisition
Description
The 1063 / 1250 Mb/s Serial Optical Converter
(SFF-1063/1250N-SW) is an integrated fiber optic
transceiver that provides a high-speed serial link at
a signaling rate of 1062.5 to 1250 Mb/s. The SFF-
1063/1250N-SW conforms to the American National
Standards Institute’s (ANSI) Fibre Channel, FC-0
specification for short wavelength operation (100-
M5-SN-I and 100-M6-SN-I). It also conforms to draft
2 of the IEEE 802.3z, 1000Base-SX standard [2].
The SFF-1063/1250N-SW is ideally suited for Fibre
Channel Arbitrated Loop (FC-AL) and Gigabit Ether-
net applications, but can be used for other serial
applications where high data rates are required.
This specification applies to a pin through hole
(PTH) module which has a 2 by 5 electrical connec-
tor pin configuration.
The SFF-1063/1250N-SW uses a short wavelength
(850nm) VCSEL (Vertical Cavity Surface Emitter
Laser) source. This enables low cost data transmis-
sion over optical fibers at distances up to 550m. A
50/125µm multimode optical fiber, terminated with
an industry standard LC connector, is the preferred
medium. (A 62.5/125µm multimode fiber can be
substituted with shorter maximum link distances.)
Encoded (8B/10B) [3], [4], gigabit/sec, serial, differ-
ential, PECL signals traverse a connector interfac-
ing the SFF-1063/1250N-SW to the host card. The
serial data modulates the laser and is sent out over
the outgoing fiber of a duplex cable.
Incoming, modulated light is detected by a photore-
ceiver mounted in the LC receptacle. The optical
signal is converted to an electrical one, amplified
and delivered to the host card. This module is
designed to work with industry standard “10b” Seri-
alizer/Deserializer modules.
The SFF-1063/1250N-SW is a Class 1 laser safe
product. The optical power levels, under normal
operation, are at eye safe levels. Optical fiber cables
can be connected and disconnected without shut-
ting off the laser transmitter.
SFF.02
1/24/00
Page 1 of 16




IBM Microelectronics
IBM Microelectronics

IBM42F10SNNAA20 Datasheet Preview

IBM42F10SNNAA20 Datasheet

(IBM42F10SNNAA20 / IBM42F12SNNAA20) Small Form Factor Transceiver

No Preview Available !

IBM42F10SNNAA20 pdf
www.DataSheet4U.com
IBM42F10SNNAA20
IBM42F12SNNAA20
1063/1250MBd Small Form Factor Transceiver with Signal Detect
Package Outline
Pin Assignments
Pin Name
Rx Ground
Rx Power
Rx_SD
Rx_DAT -
Rx_DAT +
Tx Power
Tx Ground
Tx_Disable
Tx_DAT +
Tx_DAT -
Type
Ground
Power
Status Out
Signal Out
Signal Out
Power
Ground
Control In
Signal In
Signal In
Pin #
1
2
3
4
5
6
7
8
9
10
Ordering Information
Product Descriptor
SFF-1063/1250N-SW
Part Number
IBM42F10SNNAA20
IBM42F12SNNAA20
Signaling Rate
1062.5Mb/s
1250Mb/s
Wavelength
850nm
Laser Safety Compliance Requirements
The SFF-1063/1250N-SW is designed and certified
as a Class 1 laser product. If the power supply volt-
age exceeds 4.0 volts, this may no longer remain a
Class 1 product. The system using the SFF-
1063/1250N-SW must provide power supply over
voltage protection that guarantees the supply does
not exceed 4.0 volts under all fault conditions.
Caution: Operating the power supply above 4.0V or
otherwise operating the SFF-1063/1250N-SW in a
manner inconsistent with its design and function
may result in hazardous radiation exposure, and
may be considered an act of modifying or new man-
ufacturing of a laser product under US regulations
contained in 21 CFR(J) or CENELEC regulations
contained in EN 60825. The person(s) performing
such an act is required by law to recertify and
reidentify the product in accordance with the provi-
sions of 21 CFR(J) for distribution within the United
States, and in accordance with provisions of CEN-
ELEC EN 60825 (or successive regulations) for dis-
tribution within the CENELEC countries or countries
using the IEC 825 standard.
ESD Handling
Take normal static precautions during handling and
assembly of the SFF-1063/1250N-SW to prevent
damage and/or degradation that can be induced by
electrostatic discharge.
Page 2 of 16
SFF.02
1/24/00




IBM Microelectronics
IBM Microelectronics

IBM42F10SNNAA20 Datasheet Preview

IBM42F10SNNAA20 Datasheet

(IBM42F10SNNAA20 / IBM42F12SNNAA20) Small Form Factor Transceiver

No Preview Available !

IBM42F10SNNAA20 pdf
www.DataSheet4U.com
Block Diagram
Optical
IBM42F10SNNAA20
IBM42F12SNNAA20
1063/1250MBd Small Form Factor Transceiver with Signal Detect
Receive Section
Electrical
Fiber
Input
Photoreceiver
Post-amp
and
Rx_SD
+Rx_DAT
-Rx_DAT
Rx_SD
Fiber
Output
Laser
Transmit Section
AC Modulation
DC Drive
and
Safety Control
Fault
Sense
+Tx_DAT
-Tx_DAT
Tx_Disable
Transmit Section
The input, an AC coupled differential data stream from the host, enters the AC Modulation section of the laser
driver circuitry where it modulates the output optical intensity of a semiconductor laser. The DC Drive main-
tains the laser at the correct preset power level. In addition, safety circuits in the DC Drive will shut off the
laser if a fault is detected. The host must provide the AC coupling for the +Tx/-Tx lines. A 10nF capacitor is
recommended.
Receive Section
The incoming modulated optical signal is converted to an electrical signal by the photoreceiver. This electrical
signal is then amplified and converted to a differential serial output data stream and delivered to the host. A
transition detector detects sufficient AC level of modulated light entering the photoreceiver. This signal is pro-
vided to the host as a signal detect status line. The host must provide the AC coupling for the +Rx/-Rx lines.
A 10 nF capacitor is recommended.
SFF.02
1/24/00
Page 3 of 16




Part Number IBM42F10SNNAA20
Description (IBM42F10SNNAA20 / IBM42F12SNNAA20) Small Form Factor Transceiver
Maker IBM Microelectronics
Total Page 18 Pages
PDF Download
IBM42F10SNNAA20 pdf
Download PDF File
IBM42F10SNNAA20 pdf
View for Mobile






Related Datasheet

1 IBM42F10SNNAA20 (IBM42F10SNNAA20 / IBM42F12SNNAA20) Small Form Factor Transceiver IBM Microelectronics
IBM Microelectronics
IBM42F10SNNAA20 pdf




Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components