http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf



Diodes Semiconductor Electronic Components Datasheet

AH5792 Datasheet

SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER

No Preview Available !

AH5792 pdf
AH5792
SINGLE PHASE HALL EFFECT LATCH SMART
FAN MOTOR COwNwwT.RDOataLSLheEetR4U.com
Description
Pin Assignments
The AH5792 is a single chip solution for driving single-coil
brush-less DC fans and motors. The AH5792 employs a
bidirectional full bridge driver output stage for single coil fan
motor applications. The device includes features such as
Rotor Lock Protection with rotor lock detection and automatic
self-restart to avoid damage to the coil when the rotor is
blocked.
The AH5792 also offers an externally controlled Tachometer
(Frequency Generator Pin) open -drain output which makes it
easier to connect with external interface such as hardware
monitoring. The FG is half (1/2) the magnetic change
frequency.
The devices are packaged in SOT553 and SOT89-5L small
outline packages for applications such as small motors like
vibration motors or ultra thin cooling fans.
( Top View )
O2 1
5 FG
VSS 2
O1 3
SOT553
NC
4 Vdd
( Top View )
O2 1
5 FG
Vss 2
NC
O1 3
74 Vdd
SOT89-5L
Features
• Support single-phase full wave min fan driver
• Built-in Hall sensor input amplifier
• Low voltage startup ( Vdd=1.8V )
• Lock detection and automatic self-restart
• Without external timing capacitor, Reduces the numbers
of external component required
• FG output
• Low profile package : SOT553 and SOT89-5L
• “Green” Molding Compound
Applications
• 3.3V / 5V Min. DC Fans (Eight Pole)
• Low Voltage / BLDC Motors
• Micro-Vibration Motors
AH5792
Document number: DS314641 Rev. 6 - 2
1 of 10
www.diodes.com
July 2010
© Diodes Incorporated



Diodes Semiconductor Electronic Components Datasheet

AH5792 Datasheet

SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER

No Preview Available !

AH5792 pdf
Typical Application Circuit (Note 1)
SYSTEM
POWER
D1
C1 Dz
Vdd
V SS
AH5792
SINGLE PHASE HALL EFFECT LATCH SMART
FAN MOTOR COwNwwT.RDOataLSLheEetR4U.com
AH5792
SYSTEM
POWER
10Kohm
FG FG
O1
O2
Notes:
1. Reverse connection of power supply may break the device. A countermeasure is needed such as using reverse power protection
diode D1 between power supply and Vdd terminal. In such case of using reverse power protection diode D1 because of there is no
way to return current to power supply, please take necessary measures like below.
- Connect Dz (Zener diode) between Vdd and Vss terminal, not to exceed the absolute maximum rating voltage.
- Connect a capacitor C1 between Vdd and Vss terminal, to make the path of return current to power supply.
The AH5792 has an open-drain tachometer FG output that follows the half (1/2) the magnetic change frequency. A pull-up resistor
(10Kohm, typically for System Power = 5V) connected to a supply voltage.
Pin Descriptions (Note 2)
Pin Name
Description
O1 Output driving & sinking pin 1
Vdd Power supply pin
Vss Ground pin
FG Frequency Generator (Note 2)
O2 Output driving & sinking Pin 2
NC No Connection
Notes: 2. The FG is half (1/2) the magnetic change frequency.
AH5792
Document number: DS314641 Rev. 6 - 2
2 of 10
www.diodes.com
July 2010
© Diodes Incorporated



Diodes Semiconductor Electronic Components Datasheet

AH5792 Datasheet

SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER

No Preview Available !

AH5792 pdf
Functional Block Diagram
AH5792
SINGLE PHASE HALL EFFECT LATCH SMART
FAN MOTOR COwNwwT.RDOataLSLheEetR4U.com
Vdd Power
Hall
Sensor
AMP
V SS
Frequency
Generator
FG
Logic Full Bridge
Block
Driver
Lock
Detector
O1
O2
Operating (Note 3, 4, 5)
Magentic S
N
Out 1
Out 2
FG
Normal spinning
Ton Toff
Mechanical lock
motor locked detected
“Re-start spinning”
motor locked cleared
Notes:
3. In “Normal spinning, the FG shall change its state at each rising edge of OUT2. In “Mechanical lock”, the FG state is kept as the
same as the moment of motor locked detected.
4. When magnetic is locked as “S” pole, then out1 is kept on “L”, out2 is a clock with Ton/Toff ratio. When magnetic is locked at
“N” pole, then out 2 is kept on “L”, out 1 is a clock with Ton/Toff ratio.
5. When “Re-start spinning” occurs, the motor shall ramp up to the “Normal Spinning” speed from zero. It depends on the motor
characteristics.
AH5792
Document number: DS314641 Rev. 6 - 2
3 of 10
www.diodes.com
July 2010
© Diodes Incorporated




Part Number AH5792
Description SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER
Maker Diodes Incorporated
Total Page 10 Pages
PDF Download
AH5792 pdf
Download PDF File
AH5792 pdf
View for Mobile






Related Datasheet

1 AH5792 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Diodes Incorporated
Diodes Incorporated
AH5792 pdf
2 AH5794 SINGLE PHASE HALL EFFECT LATCH FAN MOTOR DRIVER Diodes
Diodes
AH5794 pdf
3 AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Diodes
Diodes
AH5795 pdf
4 AH5798 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Diodes Incorporated
Diodes Incorporated
AH5798 pdf




Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components