http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf



Diodes Semiconductor Electronic Components Datasheet

AH3766Q-P-B Datasheet

AUTOMOTIVE HALL- EFFECT LATCH

No Preview Available !

AH3766Q-P-B pdf
Description
The AH3766Q is an AEC-Q100 qualified high-voltage, medium-
sensitivity Hall-Effect latch IC designed for brushless DC-motor
commutation, speed measurement, angular or linear encoders and
position sensors in automotive applications. To support wide range of
demanding applications, the design is optimized to operate over the
supply range of 3.0V to 28V. With chopper stabilized architecture and
an internal bandgap regulator to provide temperature compensated
supply for internal circuits, the AH3766Q provides a reliable solution
over the whole operating range. For robustness and protection, the
device has a reverse blocking diode with a Zener clamp on the
supply. The output has an overcurrent limit and a Zener clamp.
AH3766Q
HIGH-VOLTAGE, MEDIUM-SENQSITIVITY
AUTOMOTIVE HALL- EFFECT LATCH
Pin Assignments
(Top View)
GND 2
3 OUTPUT
1 VDD
SOT23
The single, open-drain output can be switched on with South pole of
sufficient strength and switched off with North pole of sufficient
strength. When the magnetic flux density (B) perpendicular to the
package is larger than the operate point (Bop), the output is switched
on (pulled low). The output is held latched until magnetic flux density
reverses and becomes lower than the release point (Brp).
(Top View)
SIP-3
3. OUTPUT
2. GND
1. VDD
Features
Bipolar Latch Operation (South Pole: On, North Pole: off)
High Sensitivity: Bop and Brp of +110G and -110G Typical
Single, Open-Drain Output with Overcurrent Limit
3.0V to 28V Operating Voltage Range
Chopper Stabilized Design Provides
Superior Temperature Stability
Minimal Switch Point Drift
Enhanced Immunity to Stress
Good RF Noise Immunity
Reverse Blocking Diode
Zener Clamp on Supply and Output Pins
-40°C to +150°C Operating Temperature
ESD: HBM 8kV, CDM: >2kV
AEC-Q100 Grade 0 Qualified
Industry Standard SOT23 and SIP-3 Packages
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
Applications
Brushless DC-Motor Commutation
Revolution Per Minute (RPM) Measurement
Angular and Linear Encoder and Position Sensing and Indexing
Flow Meters
Contactless Commutation, Speed Measurement and Angular
Position Sensing/Indexing in Automotive Applications
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
AH3766Q
Document number: DS38075 Rev. 2 - 2
1 of 13
www.diodes.com
July 2015
© Diodes Incorporated



Diodes Semiconductor Electronic Components Datasheet

AH3766Q-P-B Datasheet

AUTOMOTIVE HALL- EFFECT LATCH

No Preview Available !

AH3766Q-P-B pdf
Typical Applications Circuit
3.0V to 28V
VDD
AH3766Q
Q
RL
OUTPUT
CIN AH3766Q
GND
Note:
4. CIN is for power stabilization and to strengthen the noise immunity, the recommended capacitance is 10nF ~ 100nF. RL is the pull-up resistor.
Pin Descriptions
Package: SOT23 and SIP-3
Pin Number
1
2
3
Pin Name
VDD
GND
OUTPUT
Power Supply Input
Ground
Output Pin
Function
Functional Block Diagram
VDD
Power
switch
To All Subcircuits
Amp
Amp
Control
OUTPUT
Current
Limit
GND
AH3766Q
Document number: DS38075 Rev. 2 - 2
2 of 13
www.diodes.com
July 2015
© Diodes Incorporated



Diodes Semiconductor Electronic Components Datasheet

AH3766Q-P-B Datasheet

AUTOMOTIVE HALL- EFFECT LATCH

No Preview Available !

AH3766Q-P-B pdf
AH3766Q
Q
Absolute Maximum Ratings (Notes 5 & 6) (@TA = +25°C, unless otherwise specified.)
Symbol
VDD
VDDR
VOUT_MAX
IOUT
IOUT_R
B
PD
Ts
TJ
ESD HBM
ESD MM
ESD CDM
Supply Voltage (Note 6)
Reverse Supply Voltage (Note 6)
Output Off Voltage (Note 6)
Continuous Output Current
Reverse Output Current
Magnetic Flux Density
Characteristic
Package Power Dissipation
Storage Temperature Range
Maximum Junction Temperature
Electros Static Discharge Withstand - Human Body Model (HMB)
Electros Static Discharge Withstand - Machine Model (MM)
Electros Static Discharge Withstand - Charged Device Model (CDM)
SIP-3
SOT23
Value
32
-32
32
60
-50
Unlimited
550
230
-65 to +165
+150
8
800
2
Unit
V
V
V
mA
mA
mW
°C
°C
kV
V
kV
Notes:
5. Stresses greater than the 'Absolute Maximum Ratings' specified above may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.
6. The absolute maximum VDD of 32V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to
operate the device at the absolute maximum rated conditions for any period of time.
Recommended Operating Conditions (@TA = -40°C to +150°C, unless otherwise specified.)
Symbol
VDD
TA
Parameter
Supply Voltage
Operating Temperature Range
Operating
Operating
Conditions
Rating
3.0 to 28
-40 to +150
Unit
V
°C
Electrical Characteristics (Notes 7 & 8) (@TA = -40°C to +150°C, VDD = 3V to 28V, unless otherwise specified.)
Symbol
Parameter
Conditions
Min Typ Max Unit
VOUT_ON
ILKG
Output On Voltage
Output Leakage Current
(when output is off)
IOUT = 20mA, B > Bop
VOUT = 28V, B < Brp, Output off
-
0.2 0.4
V
-
<0.1
10
µA
IDD
IDD_R
tP_ON
fc
td
tr
tf
Supply Current
Reverse Supply Current
Device Power-On Time (start-up time)
Chopping Frequency
Response Time Delay
(time from magnetic threshold reached
to the start of the output rise or fall)
Output Rising Time
(external pull-up resistor RL and load
capacitance dependent)
Output Falling Time
(Internal switch resistance and load
capacitance dependent)
Output open, TA = +25°C
Output open, TA = -40°C to +150°C
VDD = -18V, TA = +25°C
VDD = -18V, TA = -40°C to +150°C
VDD = -28V, TA = +25°C
VDD = -28V, TA = -40°C to +150°C
VDD >= 3V, B > Bop (Note 7)
VDD >= 3V
(Note 9)
RL = 1kΩ, CL = 20pF
RL = 1kΩ, CL = 20pF
- 3 3.5 mA
- - 4 mA
- 0.6 - µA
- 0.6 1,500 µA
- 1.6 - µA
- 1.6 2,500 µA
- 10
µs
- 800 - kHz
- 3.75 -
µs
- 0.2 1 µs
- 0.1 1 µs
IOCL Output Current Limit
VZ Zener Clamp Voltage
B > Bop, (Note 10 )
IDD = 5mA
30 - 55 mA
28 - - V
Notes:
7. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid
after the start-up time of 10µs typical from the operating voltage reaching 3V.
8. Typical values are defined at TA = +25°C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production
but guaranteed by design, process control and characterization.
9. Guaranteed by design, process control and characterization. Not tested in production.
10. The device will limit the output current IOUT to current limit of IOCL.
AH3766Q
Document number: DS38075 Rev. 2 - 2
3 of 13
www.diodes.com
July 2015
© Diodes Incorporated




Part Number AH3766Q-P-B
Description AUTOMOTIVE HALL- EFFECT LATCH
Maker Diodes Incorporated
Total Page 13 Pages
PDF Download
AH3766Q-P-B pdf
Download PDF File
AH3766Q-P-B pdf
View for Mobile






Related Datasheet

1 AH3766Q-P-B AUTOMOTIVE HALL- EFFECT LATCH Diodes Incorporated
Diodes Incorporated
AH3766Q-P-B pdf




Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components