http://www.www.datasheet4u.com

900,000+ Datasheet PDF Search and Download

Datasheet4U offers most rated semiconductors datasheets pdf




Analog Devices Semiconductor Electronic Components Datasheet

AD585 Datasheet

High Speed/ Precision Sample-and-Hold Amplifier

No Preview Available !

AD585 pdf
a
High Speed, Precision
Sample-and-Hold Amplifier
AD585
FEATURES
3.0 s Acquisition Time to ؎0.01% max
Low Droop Rate: 1.0 mV/ms max
Sample/Hold Offset Step: 3 mV max
Aperture Jitter: 0.5 ns
Extended Temperature Range: –55؇C to +125؇C
Internal Hold Capacitor
Internal Application Resistors
؎12 V or ؎15 V Operation
Available in Surface Mount
APPLICATIONS
Data Acquisition Systems
Data Distribution Systems
Analog Delay & Storage
Peak Amplitude Measurements
MIL-STD-883 Compliant Versions Available
PRODUCT DESCRIPTION
The AD585 is a complete monolithic sample-and-hold circuit
consisting of a high performance operational amplifier in series
with an ultralow leakage analog switch and a FET input inte-
grating amplifier. An internal holding capacitor and matched
applications resistors have been provided for high precision and
applications flexibility.
The performance of the AD585 makes it ideal for high speed
10- and 12-bit data acquisition systems, where fast acquisition
time, low sample-to-hold offset, and low droop are critical. The
AD585 can acquire a signal to ± 0.01% in 3 µs maximum, and
then hold that signal with a maximum sample-to-hold offset of
3 mV and less than 1 mV/ms droop, using the on-chip hold
capacitor. If lower droop is required, it is possible to add a
larger external hold capacitor.
The high speed analog switch used in the AD585 exhibits
aperture jitter of 0.5 ns, enabling the device to sample full scale
(20 V peak-to-peak) signals at frequencies up to 78 kHz with
12-bit precision.
The AD585 can be used with any user-defined feedback net-
work to provide any desired gain in the sample mode. On-chip
precision thin-film resistors can be used to provide gains of +1,
–1, or +2. Output impedance in the hold mode is sufficiently
low to maintain an accurate output signal even when driving the
dynamic load presented by a successive-approximation A/D
converter. However, the output is protected against damage
from accidental short circuits.
The control signal for the HOLD command can be either active
high or active low. The differential HOLD signal is compatible
with all logic families, if a suitable reference level is provided. An
on-chip TTL reference level is provided for TTL compatibility.
FUNCTIONAL BLOCK DIAGRAM
DIP LCC/PLCC Package
The AD585 is available in three performance grades. The JP
grade is specified for the 0°C to +70°C commercial temperature
range and packaged in a 20-pin PLCC. The AQ grade is speci-
fied for the –25°C to +85°C industrial temperature range and is
packaged in a 14-pin cerdip. The SQ and SE grades are speci-
fied for the –55°C to +125°C military temperature range and
are packaged in a 14-pin cerdip and 20-pin LCC.
PRODUCT HIGHLIGHTS
1. The fast acquisition time (3 µs) and low aperture jitter
(0.5 ns) make it the first choice for very high speed data
acquisition systems.
2. The droop rate is only 1.0 mV/ms so that it may be used in
slower high accuracy systems without the loss of accuracy.
3. The low charge transfer of the analog switch keeps sample-to
hold offset below 3 mV with the on-chip 100 pF hold capaci-
tor, eliminating the trade-off between acquisition time and
S/H offset required with other SHAs.
4. The AD585 has internal pretrimmed application resistors for
applications versatility.
5. The AD585 is complete with an internal hold capacitor for
ease of use. Capacitance can be added externally to reduce
the droop rate when long hold times and high accuracy are
required.
6. The AD585 is recommended for use with 10- and 12-bit
successive-approximation A/D converters such as AD573,
AD574A, AD674A, AD7572 and AD7672.
7. The AD585 is available in versions compliant with MIL-STD-
883. Refer to the Analog Devices Military Products Databook
or current AD585/883B data sheet for detailed specifications.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703


Analog Devices Semiconductor Electronic Components Datasheet

AD585 Datasheet

High Speed/ Precision Sample-and-Hold Amplifier

No Preview Available !

AD585 pdf
AD585–SPECIFICATIONS (typical @ +25؇C and VS = ؎12 V or ؎15 V, and CH = Internal, A = +1,
HOLD active unless otherwise noted)
Model
SAMPLE/HOLD CHARACTERISTICS
Acquisition Time, 10 V Step to 0.01%
20 V Step to 0.01%
Aperture Time, 20 V p-p Input,
HOLD 0 V
Aperture Jitter, 20 V p-p Input,
HOLD 0 V
Settling Time, 20 V p-p Input,
HOLD 0 V, to 0.01%
Droop Rate
Droop Rate TMIN to TMAX
Charge Transfer
Sample-to-Hold Offset
Feedthrough
20 V p-p, 10 kHz Input
TRANSFER CHARACTERISTICS1
Open Loop Gain
VOUT = 20 V p-p, RL = 2k
Application Resistor Mismatch
Common-Mode Rejection
VCM = ± 10 V
Small Signal Gain Bandwidth
VOUT = 100 mV p-p
Full Power Bandwidth
VOUT = 20 V p-p
Slew Rate
VOUT = 20 V p-p
Output Resistance (Sample Mode)
IOUT = ± 10 mA
Output Short Circuit Current
Output Short Circuit Duration
ANALOG INPUT CHARACTERISTICS
Offset Voltage
Offset Voltage, TMIN to TMAX
Bias Current
Bias Current, TMIN to TMAX
Input Capacitance, f = 1 MHz
Input Resistance, Sample or Hold
20 V p-p Input, A = +1
DIGITAL INPUT CHARACTERISTICS
TTL Reference Output
Logic Input High Voltage
TMIN to TMAX
Logic Input Low Voltage
TMIN to TMAX
Logic Input Current (Either Input)
POWER SUPPLY CHARACTERISTICS
Operating Voltage Range
Supply Current, RL =
Power Supply Rejection, Sample Mode
TEMPERATURE RANGE
Specified Performance
PACKAGE OPTIONS3, 4
Cerdip (Q-14)
LCC (E-20A)
PLCC (P-20A)
AD585J
Min Typ Max
3
5
35
0.5
0.5
1
Doubles Every 10°C
0.3
–3 3
0.5
AD585A
Min Typ Max
3
5
35
0.5
0.5
1
Double Every 10°C
0.3
–3 3
0.5
AD585S
Min Typ Max
3
5
35
0.5
0.5
1
Doubles Every 10°C
0.3
–3 3
0.5
200,000
0.3
80
2.0
160
10
50
Indefinite
0.05
5
6
2
5
10
1012
1.2 1.4 1.6
2.0
0.8
50
+5, –10.8
6
70
± 18
10
0 +70
AD585JP
200,000
0.3
80
2.0
160
10
50
Indefinite
0.05
2
3
2
5
10
1012
1.2 1.4 1.6
2.0
0.8
50
+5, –10.8
6
70
± 18
10
–25 +85
AD585AQ
200,000
0.3
80
2.0
160
10
50
Indefinite
0.05
2
3
2
20 502
10
1012
1.2 1.4 1.6
2.0
0.7
50
+5, –10.8
6
70
± 18
10
–55 +125
AD585SQ
AD585SE
Units
µs
µs
ns
ns
µs
mV/ms
pC
mV
mV
V/V
%
dB
MHz
kHz
V/µs
mA
mV
mV
nA
nA
pF
V
V
V
µA
V
mA
dB
°C
NOTES
1Maximum input signal is the minimum supply minus a headroom voltage of 2.5 V.
2Not tested at –55°C.
3E = Leadless Ceramic Chip Carrier; P = Plastic Leaded Chip Carrier; Q = Cerdip.
4For AD585/883B specifications, refer to Analog Devices Military Products Databook.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical
test. Results from those tests are used to calculate outgoing quality levels.
All min and max specifications are guaranteed, although only those shown in
boldface are tested on all production units.
–2– REV. A


Part Number AD585
Description High Speed/ Precision Sample-and-Hold Amplifier
Maker Analog Devices
Total Page 6 Pages
PDF Download
AD585 pdf
Download PDF File
AD585 pdf
View for Mobile



Buy Electronic Components




Related Datasheet

1 AD580 High Precision 2.5 V IC Reference Analog Devices
Analog Devices
AD580 pdf
2 AD581 High Precision 10 V IC Reference Analog Devices
Analog Devices
AD581 pdf
3 AD582 Low Cost Sample/Hold Amplifier Analog Devices
Analog Devices
AD582 pdf
4 AD5821 single 10-bit digital-to-analog converter Analog Devices
Analog Devices
AD5821 pdf
5 AD5821A I2C DAC Analog Devices
Analog Devices
AD5821A pdf
6 AD5823 10-Bit VCM Driver Analog Devices
Analog Devices
AD5823 pdf
7 AD5823-1 10-Bit VCM Driver Analog Devices
Analog Devices
AD5823-1 pdf
8 AD583 IC Sample and Hold Gated OP Amp Analog Devices
Analog Devices
AD583 pdf
9 AD584 Precision Voltage Reference Analog Devices
Analog Devices
AD584 pdf






Part Number Start With

0    1    2    3    4    5    6    7    8    9    A    B    C    D    E    F    G    H    I    J    K    L    M    N    O    P    Q    R    S    T    U    V    W    X    Y    Z

site map

webmaste! click here

contact us

Buy Components